Hello,
On Mon, May 23, 2016 at 04:48:40PM +0530, R, Vignesh wrote:
> On 5/22/2016 3:56 PM, Uwe Kleine-König wrote:
> > Hello,
> >
> > On Thu, May 19, 2016 at 02:34:00PM +0530, Vignesh R wrote:
> >> There are rotary-encoders where GPIO lines reflect the actual position
> >> of the rotary encoder dial. For example, if dial points to 9, then four
> >> GPIO lines connected to the rotary encoder will read HLLH(1001b = 9).
> >> Add support for such rotary-encoder.
> >> The driver relies on rotary-encoder,absolute-encoder DT property to
> >> detect such encoders.
> >> Since, GPIO IRQs are not necessary to work with
> >> such encoders, optional polling mode support is added using
> >
> > I don't understand this. It's necessary in the same way as with the
> > already supported devices. I.e. you want to trigger an irq when the
> > encoder is moved and then check for it's position in the handler.
> >
>
> Unlike already supported device, there is no need to count steps or
> determine the direction of rotation. Hence, IRQ is not a requirement,
> periodically polling the gpio lines is more than sufficient. With
> absolute encoder, you are able to determine the current position at any
> time just by looking at the gpio inputs.
The timing might not be that critical, but there is no reason to operate
this device without irqs, is there?
> Suppose we poll device at t=0ms and see gpio values are LLLH(1), if we
> again poll device at t=500ms(which is what input_poll_dev helps to do)
> and see that gpio values is LLHH(3), then we know that rotary encoder
> has changed to 3. This can be done w/o IRQ for absolute encoders.
>
> >> diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt
> >> index 6c9f0c8a846c..9c928dbd1500 100644
> >> --- a/Documentation/devicetree/bindings/input/rotary-encoder.txt
> >> +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt
> >> @@ -12,6 +12,10 @@ Optional properties:
> >> - rotary-encoder,relative-axis: register a relative axis rather than an
> >> absolute one. Relative axis will only generate +1/-1 events on the input
> >> device, hence no steps need to be passed.
> >> +- rotary-encoder,absolute-encoder: support encoders where GPIO lines
> >> + reflect the actual position of the rotary encoder dial. For example,
> >> + if dial points to 9, then four GPIO lines read HLLH(1001b = 9).
> >> + In this case, rotary-encoder,steps-per-period needed not be defined.
> >
> > IMHO this is wrong, I'd formalize this device as:
> >
> > {
> > compatible = "rotary-encoder";
> > gpios = <&gpio 19 1>, <&gpio 20 0>, <...>, <...>;
> > rotary-encoder,encoding = "binary";
> > rotary-encoder,steps = <16>;
> > rotary-encoder,steps-per-period = <16>;
>
> The above bindings essential means quarter_period device. I would not
> like to bother with all the logic in rotary_encoder_quarter_period_irq()
> when we can know encoder->pos by directly reading state of gpio lines.
OK, we have code that is more complex than it needs to be for your
device. But your device is a special case of the supported devices, so
I'd say don't bother that there is more logic in the driver than you
need and be lucky.
> > rotary-encoder,rollover;
> > }
> >
> > and support this with a v4 of
> >
> > http://thread.gmane.org/gmane.linux.kernel.input/48892
> >
> >
>
> IMHO, there needs to be separate IRQ handler for absolute encoders so
> that the driver logic is greatly simplified.
As above, the added complexity can handle your case just fine. So just
use it.
One thing I see to improve is to make use of the additional GPIOs, but
this is orthogonal to the different encoding and the question if polling
is enough here.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
