On Jan 14 2016 or thereabouts, Andrew Duggan wrote:
> Synaptics uses the Register Mapped Interface (RMI) protocol as a
> communications interface for their devices. This driver adds the core
> functionality needed to interface with RMI4 devices.
>
> RMI devices can be connected to the host via several transport protocols
> and can supports a wide variety of functionality defined by RMI functions.
> Support for transport protocols and RMI functions are implemented in
> individual drivers. The RMI4 core driver uses a bus architecture to
> facilitate the various combinations of transport and function drivers
> needed by a particular device.
>
I finally was able to test the v2 of the series on an SMBus touchpad.
Everything works OK, and the code is much better now I think.
There is just one caveat which took me a little time and I am sure we
need to fix in rmi_driver.c:
> Signed-off-by: Andrew Duggan <aduggan@xxxxxxxxxxxxx>
> Signed-off-by: Christopher Heiny <cheiny@xxxxxxxxxxxxx>
> ---
> drivers/input/Kconfig | 2 +
> drivers/input/Makefile | 2 +
> drivers/input/rmi4/Kconfig | 12 +
> drivers/input/rmi4/Makefile | 2 +
> drivers/input/rmi4/rmi_bus.c | 378 +++++++++++++++
> drivers/input/rmi4/rmi_bus.h | 189 ++++++++
> drivers/input/rmi4/rmi_driver.c | 1024 +++++++++++++++++++++++++++++++++++++++
> drivers/input/rmi4/rmi_driver.h | 103 ++++
> drivers/input/rmi4/rmi_f01.c | 575 ++++++++++++++++++++++
> include/linux/rmi.h | 213 ++++++++
> include/uapi/linux/input.h | 1 +
> 11 files changed, 2501 insertions(+)
> create mode 100644 drivers/input/rmi4/Kconfig
> create mode 100644 drivers/input/rmi4/Makefile
> create mode 100644 drivers/input/rmi4/rmi_bus.c
> create mode 100644 drivers/input/rmi4/rmi_bus.h
> create mode 100644 drivers/input/rmi4/rmi_driver.c
> create mode 100644 drivers/input/rmi4/rmi_driver.h
> create mode 100644 drivers/input/rmi4/rmi_f01.c
> create mode 100644 include/linux/rmi.h
>
> diff --git a/drivers/input/Kconfig b/drivers/input/Kconfig
> index a35532e..6261874 100644
> --- a/drivers/input/Kconfig
> +++ b/drivers/input/Kconfig
> @@ -201,6 +201,8 @@ source "drivers/input/touchscreen/Kconfig"
>
> source "drivers/input/misc/Kconfig"
>
> +source "drivers/input/rmi4/Kconfig"
> +
> endif
>
> menu "Hardware I/O ports"
> diff --git a/drivers/input/Makefile b/drivers/input/Makefile
> index 0c9302c..595820b 100644
> --- a/drivers/input/Makefile
> +++ b/drivers/input/Makefile
> @@ -26,3 +26,5 @@ obj-$(CONFIG_INPUT_TOUCHSCREEN) += touchscreen/
> obj-$(CONFIG_INPUT_MISC) += misc/
>
> obj-$(CONFIG_INPUT_APMPOWER) += apm-power.o
> +
> +obj-$(CONFIG_RMI4_CORE) += rmi4/
> diff --git a/drivers/input/rmi4/Kconfig b/drivers/input/rmi4/Kconfig
> new file mode 100644
> index 0000000..75ce185
> --- /dev/null
> +++ b/drivers/input/rmi4/Kconfig
> @@ -0,0 +1,12 @@
> +#
> +# RMI4 configuration
> +#
> +config RMI4_CORE
> + tristate "Synaptics RMI4 bus support"
> + help
> + Say Y here if you want to support the Synaptics RMI4 bus. This is
> + required for all RMI4 device support.
> +
> + If unsure, say Y.
> +
> + This feature is not currently available as a loadable module.
> diff --git a/drivers/input/rmi4/Makefile b/drivers/input/rmi4/Makefile
> new file mode 100644
> index 0000000..12f2197
> --- /dev/null
> +++ b/drivers/input/rmi4/Makefile
> @@ -0,0 +1,2 @@
> +obj-$(CONFIG_RMI4_CORE) += rmi_core.o
> +rmi_core-y := rmi_bus.o rmi_driver.o rmi_f01.o
> diff --git a/drivers/input/rmi4/rmi_bus.c b/drivers/input/rmi4/rmi_bus.c
> new file mode 100644
> index 0000000..e7dcd39
> --- /dev/null
> +++ b/drivers/input/rmi4/rmi_bus.c
> @@ -0,0 +1,378 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/device.h>
> +#include <linux/kconfig.h>
> +#include <linux/list.h>
> +#include <linux/pm.h>
> +#include <linux/rmi.h>
> +#include <linux/slab.h>
> +#include <linux/types.h>
> +#include <linux/of.h>
> +#include "rmi_bus.h"
> +#include "rmi_driver.h"
> +
> +int debug_flags;
> +module_param(debug_flags, int, 0444);
> +MODULE_PARM_DESC(debug_flags, "control debugging information");
> +
> +void rmi_dbg(int flags, struct device *dev, const char *fmt, ...)
> +{
> + struct va_format vaf;
> + va_list args;
> +
> + if (flags & debug_flags) {
> + va_start(args, fmt);
> +
> + vaf.fmt = fmt;
> + vaf.va = &args;
> +
> + dev_printk(KERN_DEBUG, dev, "%pV", &vaf);
> +
> + va_end(args);
> + }
> +}
> +EXPORT_SYMBOL_GPL(rmi_dbg);
> +
> +/*
> + * RMI Physical devices
> + *
> + * Physical RMI device consists of several functions serving particular
> + * purpose. For example F11 is a 2D touch sensor while F01 is a generic
> + * function present in every RMI device.
> + */
> +
> +static void rmi_release_device(struct device *dev)
> +{
> + struct rmi_device *rmi_dev = to_rmi_device(dev);
> +
> + kfree(rmi_dev);
> +}
> +
> +static struct device_type rmi_device_type = {
> + .name = "rmi4_sensor",
> + .release = rmi_release_device,
> +};
> +
> +bool rmi_is_physical_device(struct device *dev)
> +{
> + return dev->type == &rmi_device_type;
> +}
> +
> +/**
> + * rmi_register_transport_device - register a transport device connection
> + * on the RMI bus. Transport drivers provide communication from the devices
> + * on a bus (such as SPI, I2C, and so on) to the RMI4 sensor.
> + *
> + * @xport: the transport device to register
> + */
> +int rmi_register_transport_device(struct rmi_transport_dev *xport)
> +{
> + static atomic_t transport_device_count = ATOMIC_INIT(0);
> + struct rmi_device *rmi_dev;
> + int error;
> +
> + rmi_dev = kzalloc(sizeof(struct rmi_device), GFP_KERNEL);
> + if (!rmi_dev)
> + return -ENOMEM;
> +
> + device_initialize(&rmi_dev->dev);
> +
> + rmi_dev->xport = xport;
> + rmi_dev->number = atomic_inc_return(&transport_device_count) - 1;
> +
> + dev_set_name(&rmi_dev->dev, "rmi4-%02d", rmi_dev->number);
> +
> + rmi_dev->dev.bus = &rmi_bus_type;
> + rmi_dev->dev.type = &rmi_device_type;
> +
> + xport->rmi_dev = rmi_dev;
> +
> + error = device_add(&rmi_dev->dev);
> + if (error)
> + goto err_put_device;
> +
> + rmi_dbg(RMI_DEBUG_CORE, xport->dev,
> + "%s: Registered %s as %s.\n", __func__,
> + dev_name(rmi_dev->xport->dev), dev_name(&rmi_dev->dev));
> +
> + return 0;
> +
> +err_put_device:
> + put_device(&rmi_dev->dev);
> + return error;
> +}
> +EXPORT_SYMBOL_GPL(rmi_register_transport_device);
> +
> +/**
> + * rmi_unregister_transport_device - unregister a transport device connection
> + * @xport: the transport driver to unregister
> + *
> + */
> +void rmi_unregister_transport_device(struct rmi_transport_dev *xport)
> +{
> + struct rmi_device *rmi_dev = xport->rmi_dev;
> +
> + device_del(&rmi_dev->dev);
> + put_device(&rmi_dev->dev);
> +}
> +EXPORT_SYMBOL(rmi_unregister_transport_device);
> +
> +
> +/* Function specific stuff */
> +
> +static void rmi_release_function(struct device *dev)
> +{
> + struct rmi_function *fn = to_rmi_function(dev);
> +
> + kfree(fn);
> +}
> +
> +static struct device_type rmi_function_type = {
> + .name = "rmi4_function",
> + .release = rmi_release_function,
> +};
> +
> +bool rmi_is_function_device(struct device *dev)
> +{
> + return dev->type == &rmi_function_type;
> +}
> +
> +static int rmi_function_match(struct device *dev, struct device_driver *drv)
> +{
> + struct rmi_function_handler *handler = to_rmi_function_handler(drv);
> + struct rmi_function *fn = to_rmi_function(dev);
> +
> + return fn->fd.function_number == handler->func;
> +}
> +
> +static int rmi_function_probe(struct device *dev)
> +{
> + struct rmi_function *fn = to_rmi_function(dev);
> + struct rmi_function_handler *handler =
> + to_rmi_function_handler(dev->driver);
> + int error;
> +
> + if (handler->probe) {
> + error = handler->probe(fn);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_function_remove(struct device *dev)
> +{
> + struct rmi_function *fn = to_rmi_function(dev);
> + struct rmi_function_handler *handler =
> + to_rmi_function_handler(dev->driver);
> +
> + if (handler->remove)
> + handler->remove(fn);
> +
> + return 0;
> +}
> +
> +int rmi_register_function(struct rmi_function *fn)
> +{
> + struct rmi_device *rmi_dev = fn->rmi_dev;
> + int error;
> +
> + device_initialize(&fn->dev);
> +
> + dev_set_name(&fn->dev, "%s.fn%02x",
> + dev_name(&rmi_dev->dev), fn->fd.function_number);
> +
> + fn->dev.parent = &rmi_dev->dev;
> + fn->dev.type = &rmi_function_type;
> + fn->dev.bus = &rmi_bus_type;
> +
> + error = device_add(&fn->dev);
> + if (error) {
> + dev_err(&rmi_dev->dev,
> + "Failed device_register function device %s\n",
> + dev_name(&fn->dev));
> + goto err_put_device;
> + }
> +
> + rmi_dbg(RMI_DEBUG_CORE, &rmi_dev->dev, "Registered F%02X.\n",
> + fn->fd.function_number);
> +
> + return 0;
> +
> +err_put_device:
> + put_device(&fn->dev);
> + return error;
> +}
> +
> +void rmi_unregister_function(struct rmi_function *fn)
> +{
> + device_del(&fn->dev);
> +
> + if (fn->dev.of_node)
> + of_node_put(fn->dev.of_node);
> +
> + put_device(&fn->dev);
> +}
> +
> +/**
> + * rmi_register_function_handler - register a handler for an RMI function
> + * @handler: RMI handler that should be registered.
> + * @module: pointer to module that implements the handler
> + * @mod_name: name of the module implementing the handler
> + *
> + * This function performs additional setup of RMI function handler and
> + * registers it with the RMI core so that it can be bound to
> + * RMI function devices.
> + */
> +int __rmi_register_function_handler(struct rmi_function_handler *handler,
> + struct module *owner,
> + const char *mod_name)
> +{
> + struct device_driver *driver = &handler->driver;
> + int error;
> +
> + driver->bus = &rmi_bus_type;
> + driver->owner = owner;
> + driver->mod_name = mod_name;
> + driver->probe = rmi_function_probe;
> + driver->remove = rmi_function_remove;
> +
> + error = driver_register(&handler->driver);
> + if (error) {
> + pr_err("driver_register() failed for %s, error: %d\n",
> + handler->driver.name, error);
> + return error;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(__rmi_register_function_handler);
> +
> +/**
> + * rmi_unregister_function_handler - unregister given RMI function handler
> + * @handler: RMI handler that should be unregistered.
> + *
> + * This function unregisters given function handler from RMI core which
> + * causes it to be unbound from the function devices.
> + */
> +void rmi_unregister_function_handler(struct rmi_function_handler *handler)
> +{
> + driver_unregister(&handler->driver);
> +}
> +EXPORT_SYMBOL_GPL(rmi_unregister_function_handler);
> +
> +/* Bus specific stuff */
> +
> +static int rmi_bus_match(struct device *dev, struct device_driver *drv)
> +{
> + bool physical = rmi_is_physical_device(dev);
> +
> + /* First see if types are not compatible */
> + if (physical != rmi_is_physical_driver(drv))
> + return 0;
> +
> + return physical || rmi_function_match(dev, drv);
> +}
> +
> +struct bus_type rmi_bus_type = {
> + .match = rmi_bus_match,
> + .name = "rmi4",
> +};
> +
> +static struct rmi_function_handler *fn_handlers[] = {
> + &rmi_f01_handler,
> +};
> +
> +#define RMI_FN_HANDLER_ARRAY_SIZE \
> + (sizeof(fn_handlers) / sizeof(struct rmi_function_handler *))
> +
> +static void __rmi_unregister_function_handlers(int start_idx)
> +{
> + int i;
> +
> + for (i = start_idx; i >= 0; i--)
> + rmi_unregister_function_handler(fn_handlers[i]);
> +}
> +
> +static void rmi_unregister_function_handlers(void)
> +{
> + __rmi_unregister_function_handlers(RMI_FN_HANDLER_ARRAY_SIZE - 1);
> +}
> +
> +static int rmi_register_function_handlers(void)
> +{
> + int ret;
> + int i;
> +
> + for (i = 0; i < RMI_FN_HANDLER_ARRAY_SIZE; i++) {
> + ret = rmi_register_function_handler(fn_handlers[i]);
> + if (ret) {
> + pr_err("%s: error registering the RMI F%02x handler: %d\n",
> + __func__, fn_handlers[i]->func, ret);
> + goto err_unregister_function_handlers;
> + }
> + }
> +
> + return 0;
> +
> +err_unregister_function_handlers:
> + __rmi_unregister_function_handlers(i - 1);
> + return ret;
> +}
> +
> +static int __init rmi_bus_init(void)
> +{
> + int error;
> +
> + error = bus_register(&rmi_bus_type);
> + if (error) {
> + pr_err("%s: error registering the RMI bus: %d\n",
> + __func__, error);
> + return error;
> + }
> +
> + error = rmi_register_function_handlers();
> + if (error)
> + goto err_unregister_bus;
> +
> + error = rmi_register_physical_driver();
> + if (error) {
> + pr_err("%s: error registering the RMI physical driver: %d\n",
> + __func__, error);
> + goto err_unregister_bus;
> + }
> +
> + return 0;
> +
> +err_unregister_bus:
> + bus_unregister(&rmi_bus_type);
> + return error;
> +}
> +module_init(rmi_bus_init);
> +
> +static void __exit rmi_bus_exit(void)
> +{
> + /*
> + * We should only ever get here if all drivers are unloaded, so
> + * all we have to do at this point is unregister ourselves.
> + */
> +
> + rmi_unregister_physical_driver();
> + rmi_unregister_function_handlers();
> + bus_unregister(&rmi_bus_type);
> +}
> +module_exit(rmi_bus_exit);
> +
> +MODULE_AUTHOR("Christopher Heiny <cheiny@xxxxxxxxxxxxx");
> +MODULE_AUTHOR("Andrew Duggan <aduggan@xxxxxxxxxxxxx");
> +MODULE_DESCRIPTION("RMI bus");
> +MODULE_LICENSE("GPL");
> +MODULE_VERSION(RMI_DRIVER_VERSION);
> diff --git a/drivers/input/rmi4/rmi_bus.h b/drivers/input/rmi4/rmi_bus.h
> new file mode 100644
> index 0000000..64bb5d4
> --- /dev/null
> +++ b/drivers/input/rmi4/rmi_bus.h
> @@ -0,0 +1,189 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#ifndef _RMI_BUS_H
> +#define _RMI_BUS_H
> +
> +#include <linux/rmi.h>
> +
> +struct rmi_device;
> +
> +/**
> + * struct rmi_function - represents the implementation of an RMI4
> + * function for a particular device (basically, a driver for that RMI4 function)
> + *
> + * @fd: The function descriptor of the RMI function
> + * @rmi_dev: Pointer to the RMI device associated with this function container
> + * @dev: The device associated with this particular function.
> + *
> + * @num_of_irqs: The number of irqs needed by this function
> + * @irq_pos: The position in the irq bitfield this function holds
> + * @irq_mask: For convience, can be used to mask IRQ bits off during ATTN
> + * interrupt handling.
> + * @data: Private data pointer
> + *
> + * @node: entry in device's list of functions
> + */
> +struct rmi_function {
> + struct rmi_function_descriptor fd;
> + struct rmi_device *rmi_dev;
> + struct device dev;
> + struct list_head node;
> +
> + unsigned int num_of_irqs;
> + unsigned int irq_pos;
> + unsigned long irq_mask[];
> +};
> +
> +#define to_rmi_function(d) container_of(d, struct rmi_function, dev)
> +
> +bool rmi_is_function_device(struct device *dev);
> +
> +int __must_check rmi_register_function(struct rmi_function *);
> +void rmi_unregister_function(struct rmi_function *);
> +
> +/**
> + * struct rmi_function_handler - driver routines for a particular RMI function.
> + *
> + * @func: The RMI function number
> + * @reset: Called when a reset of the touch sensor is detected. The routine
> + * should perform any out-of-the-ordinary reset handling that might be
> + * necessary. Restoring of touch sensor configuration registers should be
> + * handled in the config() callback, below.
> + * @config: Called when the function container is first initialized, and
> + * after a reset is detected. This routine should write any necessary
> + * configuration settings to the device.
> + * @attention: Called when the IRQ(s) for the function are set by the touch
> + * sensor.
> + * @suspend: Should perform any required operations to suspend the particular
> + * function.
> + * @resume: Should perform any required operations to resume the particular
> + * function.
> + *
> + * All callbacks are expected to return 0 on success, error code on failure.
> + */
> +struct rmi_function_handler {
> + struct device_driver driver;
> +
> + u8 func;
> +
> + int (*probe)(struct rmi_function *fn);
> + void (*remove)(struct rmi_function *fn);
> + int (*config)(struct rmi_function *fn);
> + int (*reset)(struct rmi_function *fn);
> + int (*attention)(struct rmi_function *fn, unsigned long *irq_bits);
> + int (*suspend)(struct rmi_function *fn);
> + int (*resume)(struct rmi_function *fn);
> +};
> +
> +#define to_rmi_function_handler(d) \
> + container_of(d, struct rmi_function_handler, driver)
> +
> +int __must_check __rmi_register_function_handler(struct rmi_function_handler *,
> + struct module *, const char *);
> +#define rmi_register_function_handler(handler) \
> + __rmi_register_function_handler(handler, THIS_MODULE, KBUILD_MODNAME)
> +
> +void rmi_unregister_function_handler(struct rmi_function_handler *);
> +
> +
> +
> +#define to_rmi_driver(d) \
> + container_of(d, struct rmi_driver, driver)
> +
> +#define to_rmi_device(d) container_of(d, struct rmi_device, dev)
> +
> +static inline struct rmi_device_platform_data *
> +rmi_get_platform_data(struct rmi_device *d)
> +{
> + return &d->xport->pdata;
> +}
> +
> +bool rmi_is_physical_device(struct device *dev);
> +
> +/**
> + * rmi_read - read a single byte
> + * @d: Pointer to an RMI device
> + * @addr: The address to read from
> + * @buf: The read buffer
> + *
> + * Reads a single byte of data using the underlying transport protocol
> + * into memory pointed by @buf. It returns 0 on success or a negative
> + * error code.
> + */
> +static inline int rmi_read(struct rmi_device *d, u16 addr, u8 *buf)
> +{
> + return d->xport->ops->read_block(d->xport, addr, buf, 1);
> +}
> +
> +/**
> + * rmi_read_block - read a block of bytes
> + * @d: Pointer to an RMI device
> + * @addr: The start address to read from
> + * @buf: The read buffer
> + * @len: Length of the read buffer
> + *
> + * Reads a block of byte data using the underlying transport protocol
> + * into memory pointed by @buf. It returns 0 on success or a negative
> + * error code.
> + */
> +static inline int rmi_read_block(struct rmi_device *d, u16 addr,
> + void *buf, size_t len)
> +{
> + return d->xport->ops->read_block(d->xport, addr, buf, len);
> +}
> +
> +/**
> + * rmi_write - write a single byte
> + * @d: Pointer to an RMI device
> + * @addr: The address to write to
> + * @data: The data to write
> + *
> + * Writes a single byte using the underlying transport protocol. It
> + * returns zero on success or a negative error code.
> + */
> +static inline int rmi_write(struct rmi_device *d, u16 addr, u8 data)
> +{
> + return d->xport->ops->write_block(d->xport, addr, &data, 1);
> +}
> +
> +/**
> + * rmi_write_block - write a block of bytes
> + * @d: Pointer to an RMI device
> + * @addr: The start address to write to
> + * @buf: The write buffer
> + * @len: Length of the write buffer
> + *
> + * Writes a block of byte data from buf using the underlaying transport
> + * protocol. It returns the amount of bytes written or a negative error code.
> + */
> +static inline int rmi_write_block(struct rmi_device *d, u16 addr,
> + const void *buf, size_t len)
> +{
> + return d->xport->ops->write_block(d->xport, addr, buf, len);
> +}
> +
> +int rmi_for_each_dev(void *data, int (*func)(struct device *dev, void *data));
> +
> +extern struct bus_type rmi_bus_type;
> +
> +int rmi_of_property_read_u32(struct device *dev, u32 *result,
> + const char *prop, bool optional);
> +int rmi_of_property_read_u16(struct device *dev, u16 *result,
> + const char *prop, bool optional);
> +int rmi_of_property_read_u8(struct device *dev, u8 *result,
> + const char *prop, bool optional);
> +
> +#define RMI_DEBUG_CORE BIT(0)
> +#define RMI_DEBUG_XPORT BIT(1)
> +#define RMI_DEBUG_FN BIT(2)
> +#define RMI_DEBUG_2D_SENSOR BIT(3)
> +
> +void rmi_dbg(int flags, struct device *dev, const char *fmt, ...);
> +#endif
> diff --git a/drivers/input/rmi4/rmi_driver.c b/drivers/input/rmi4/rmi_driver.c
> new file mode 100644
> index 0000000..f8bb7e0
> --- /dev/null
> +++ b/drivers/input/rmi4/rmi_driver.c
> @@ -0,0 +1,1024 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This driver provides the core support for a single RMI4-based device.
> + *
> + * The RMI4 specification can be found here (URL split for line length):
> + *
> + * http://www.synaptics.com/sites/default/files/
> + * 511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#include <linux/bitmap.h>
> +#include <linux/delay.h>
> +#include <linux/fs.h>
> +#include <linux/kconfig.h>
> +#include <linux/pm.h>
> +#include <linux/slab.h>
> +#include <uapi/linux/input.h>
> +#include <linux/rmi.h>
> +#include "rmi_bus.h"
> +#include "rmi_driver.h"
> +
> +#define HAS_NONSTANDARD_PDT_MASK 0x40
> +#define RMI4_MAX_PAGE 0xff
> +#define RMI4_PAGE_SIZE 0x100
> +#define RMI4_PAGE_MASK 0xFF00
> +
> +#define RMI_DEVICE_RESET_CMD 0x01
> +#define DEFAULT_RESET_DELAY_MS 100
> +
> +static void rmi_free_function_list(struct rmi_device *rmi_dev)
> +{
> + struct rmi_function *fn, *tmp;
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> +
> + data->f01_container = NULL;
> +
> + /* Doing it in the reverse order so F01 will be removed last */
> + list_for_each_entry_safe_reverse(fn, tmp,
> + &data->function_list, node) {
> + list_del(&fn->node);
> + rmi_unregister_function(fn);
> + }
> +}
> +
> +static int reset_one_function(struct rmi_function *fn)
> +{
> + struct rmi_function_handler *fh;
> + int retval = 0;
> +
> + if (!fn || !fn->dev.driver)
> + return 0;
> +
> + fh = to_rmi_function_handler(fn->dev.driver);
> + if (fh->reset) {
> + retval = fh->reset(fn);
> + if (retval < 0)
> + dev_err(&fn->dev, "Reset failed with code %d.\n",
> + retval);
> + }
> +
> + return retval;
> +}
> +
> +static int configure_one_function(struct rmi_function *fn)
> +{
> + struct rmi_function_handler *fh;
> + int retval = 0;
> +
> + if (!fn || !fn->dev.driver)
> + return 0;
> +
> + fh = to_rmi_function_handler(fn->dev.driver);
> + if (fh->config) {
> + retval = fh->config(fn);
> + if (retval < 0)
> + dev_err(&fn->dev, "Config failed with code %d.\n",
> + retval);
> + }
> +
> + return retval;
> +}
> +
> +static int rmi_driver_process_reset_requests(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct rmi_function *entry;
> + int retval;
> +
> + list_for_each_entry(entry, &data->function_list, node) {
> + retval = reset_one_function(entry);
> + if (retval < 0)
> + return retval;
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_driver_process_config_requests(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct rmi_function *entry;
> + int retval;
> +
> + list_for_each_entry(entry, &data->function_list, node) {
> + retval = configure_one_function(entry);
> + if (retval < 0)
> + return retval;
> + }
> +
> + return 0;
> +}
> +
> +static void process_one_interrupt(struct rmi_driver_data *data,
> + struct rmi_function *fn)
> +{
> + struct rmi_function_handler *fh;
> +
> + if (!fn || !fn->dev.driver)
> + return;
> +
> + fh = to_rmi_function_handler(fn->dev.driver);
> + if (fn->irq_mask && fh->attention) {
> + bitmap_and(data->fn_irq_bits, data->irq_status, fn->irq_mask,
> + data->irq_count);
> + if (!bitmap_empty(data->fn_irq_bits, data->irq_count))
> + fh->attention(fn, data->fn_irq_bits);
> + }
> +}
> +
> +int rmi_process_interrupt_requests(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct device *dev = &rmi_dev->dev;
> + struct rmi_function *entry;
> + int error;
> +
Here, it would be good to check if data is NULL.
I had the case were my PS/2 code was not rebased properly and the
touchpad has been forced back to PS/2 after we started the
initialisation of the RMI4 over SMBus.
We can not guarantee at the end of the probe of SMBus that we will have
drv_data of rmi_device set, as it is created after the probe.
This lead to kernel oopses here, and I think we should check and bail
out before users have a bad issue :)
Cheers,
Benjamin
PS: I rebased the SMBus patches on top of the current Dmitry's for-next
branch. I can push it somewhere if you need (there is a merge conflict).
> + if (!rmi_dev->xport->attn_data) {
> + error = rmi_read_block(rmi_dev,
> + data->f01_container->fd.data_base_addr + 1,
> + data->irq_status, data->num_of_irq_regs);
> + if (error < 0) {
> + dev_err(dev, "Failed to read irqs, code=%d\n", error);
> + return error;
> + }
> + }
> +
> + mutex_lock(&data->irq_mutex);
> + bitmap_and(data->irq_status, data->irq_status, data->current_irq_mask,
> + data->irq_count);
> + /*
> + * At this point, irq_status has all bits that are set in the
> + * interrupt status register and are enabled.
> + */
> + mutex_unlock(&data->irq_mutex);
> +
> + /*
> + * It would be nice to be able to use irq_chip to handle these
> + * nested IRQs. Unfortunately, most of the current customers for
> + * this driver are using older kernels (3.0.x) that don't support
> + * the features required for that. Once they've shifted to more
> + * recent kernels (say, 3.3 and higher), this should be switched to
> + * use irq_chip.
> + */
> + list_for_each_entry(entry, &data->function_list, node)
> + if (entry->irq_mask)
> + process_one_interrupt(data, entry);
> +
> + if (data->input)
> + input_sync(data->input);
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(rmi_process_interrupt_requests);
> +
> +static int suspend_one_function(struct rmi_function *fn)
> +{
> + struct rmi_function_handler *fh;
> + int retval = 0;
> +
> + if (!fn || !fn->dev.driver)
> + return 0;
> +
> + fh = to_rmi_function_handler(fn->dev.driver);
> + if (fh->suspend) {
> + retval = fh->suspend(fn);
> + if (retval < 0)
> + dev_err(&fn->dev, "Suspend failed with code %d.\n",
> + retval);
> + }
> +
> + return retval;
> +}
> +
> +static int rmi_suspend_functions(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct rmi_function *entry;
> + int retval;
> +
> + list_for_each_entry(entry, &data->function_list, node) {
> + retval = suspend_one_function(entry);
> + if (retval < 0)
> + return retval;
> + }
> +
> + return 0;
> +}
> +
> +static int resume_one_function(struct rmi_function *fn)
> +{
> + struct rmi_function_handler *fh;
> + int retval = 0;
> +
> + if (!fn || !fn->dev.driver)
> + return 0;
> +
> + fh = to_rmi_function_handler(fn->dev.driver);
> + if (fh->resume) {
> + retval = fh->resume(fn);
> + if (retval < 0)
> + dev_err(&fn->dev, "Resume failed with code %d.\n",
> + retval);
> + }
> +
> + return retval;
> +}
> +
> +static int rmi_resume_functions(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct rmi_function *entry;
> + int retval;
> +
> + list_for_each_entry(entry, &data->function_list, node) {
> + retval = resume_one_function(entry);
> + if (retval < 0)
> + return retval;
> + }
> +
> + return 0;
> +}
> +
> +static int enable_sensor(struct rmi_device *rmi_dev)
> +{
> + int retval = 0;
> +
> + retval = rmi_driver_process_config_requests(rmi_dev);
> + if (retval < 0)
> + return retval;
> +
> + return rmi_process_interrupt_requests(rmi_dev);
> +}
> +
> +/**
> + * rmi_driver_set_input_params - set input device id and other data.
> + *
> + * @rmi_dev: Pointer to an RMI device
> + * @input: Pointer to input device
> + *
> + */
> +static int rmi_driver_set_input_params(struct rmi_device *rmi_dev,
> + struct input_dev *input)
> +{
> + input->name = SYNAPTICS_INPUT_DEVICE_NAME;
> + input->id.vendor = SYNAPTICS_VENDOR_ID;
> + input->id.bustype = BUS_RMI;
> + return 0;
> +}
> +
> +static void rmi_driver_set_input_name(struct rmi_device *rmi_dev,
> + struct input_dev *input)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + char *device_name = rmi_f01_get_product_ID(data->f01_container);
> + char *name;
> +
> + name = devm_kasprintf(&rmi_dev->dev, GFP_KERNEL,
> + "Synaptics %s", device_name);
> + if (!name)
> + return;
> +
> + input->name = name;
> +}
> +
> +static int rmi_driver_set_irq_bits(struct rmi_device *rmi_dev,
> + unsigned long *mask)
> +{
> + int error = 0;
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct device *dev = &rmi_dev->dev;
> +
> + mutex_lock(&data->irq_mutex);
> + bitmap_or(data->new_irq_mask,
> + data->current_irq_mask, mask, data->irq_count);
> +
> + error = rmi_write_block(rmi_dev,
> + data->f01_container->fd.control_base_addr + 1,
> + data->new_irq_mask, data->num_of_irq_regs);
> + if (error < 0) {
> + dev_err(dev, "%s: Failed to change enabled interrupts!",
> + __func__);
> + goto error_unlock;
> + }
> + bitmap_copy(data->current_irq_mask, data->new_irq_mask,
> + data->num_of_irq_regs);
> +
> +error_unlock:
> + mutex_unlock(&data->irq_mutex);
> + return error;
> +}
> +
> +static int rmi_driver_clear_irq_bits(struct rmi_device *rmi_dev,
> + unsigned long *mask)
> +{
> + int error = 0;
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct device *dev = &rmi_dev->dev;
> +
> + mutex_lock(&data->irq_mutex);
> + bitmap_andnot(data->new_irq_mask,
> + data->current_irq_mask, mask, data->irq_count);
> +
> + error = rmi_write_block(rmi_dev,
> + data->f01_container->fd.control_base_addr + 1,
> + data->new_irq_mask, data->num_of_irq_regs);
> + if (error < 0) {
> + dev_err(dev, "%s: Failed to change enabled interrupts!",
> + __func__);
> + goto error_unlock;
> + }
> + bitmap_copy(data->current_irq_mask, data->new_irq_mask,
> + data->num_of_irq_regs);
> +
> +error_unlock:
> + mutex_unlock(&data->irq_mutex);
> + return error;
> +}
> +
> +static int rmi_driver_reset_handler(struct rmi_device *rmi_dev)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + int error;
> +
> + /*
> + * Can get called before the driver is fully ready to deal with
> + * this situation.
> + */
> + if (!data || !data->f01_container) {
> + dev_warn(&rmi_dev->dev,
> + "Not ready to handle reset yet!\n");
> + return 0;
> + }
> +
> + error = rmi_read_block(rmi_dev,
> + data->f01_container->fd.control_base_addr + 1,
> + data->current_irq_mask, data->num_of_irq_regs);
> + if (error < 0) {
> + dev_err(&rmi_dev->dev, "%s: Failed to read current IRQ mask.\n",
> + __func__);
> + return error;
> + }
> +
> + error = rmi_driver_process_reset_requests(rmi_dev);
> + if (error < 0)
> + return error;
> +
> + error = rmi_driver_process_config_requests(rmi_dev);
> + if (error < 0)
> + return error;
> +
> + return 0;
> +}
> +
> +int rmi_read_pdt_entry(struct rmi_device *rmi_dev, struct pdt_entry *entry,
> + u16 pdt_address)
> +{
> + u8 buf[RMI_PDT_ENTRY_SIZE];
> + int error;
> +
> + error = rmi_read_block(rmi_dev, pdt_address, buf, RMI_PDT_ENTRY_SIZE);
> + if (error) {
> + dev_err(&rmi_dev->dev, "Read PDT entry at %#06x failed, code: %d.\n",
> + pdt_address, error);
> + return error;
> + }
> +
> + entry->page_start = pdt_address & RMI4_PAGE_MASK;
> + entry->query_base_addr = buf[0];
> + entry->command_base_addr = buf[1];
> + entry->control_base_addr = buf[2];
> + entry->data_base_addr = buf[3];
> + entry->interrupt_source_count = buf[4] & RMI_PDT_INT_SOURCE_COUNT_MASK;
> + entry->function_version = (buf[4] & RMI_PDT_FUNCTION_VERSION_MASK) >> 5;
> + entry->function_number = buf[5];
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(rmi_read_pdt_entry);
> +
> +static void rmi_driver_copy_pdt_to_fd(const struct pdt_entry *pdt,
> + struct rmi_function_descriptor *fd)
> +{
> + fd->query_base_addr = pdt->query_base_addr + pdt->page_start;
> + fd->command_base_addr = pdt->command_base_addr + pdt->page_start;
> + fd->control_base_addr = pdt->control_base_addr + pdt->page_start;
> + fd->data_base_addr = pdt->data_base_addr + pdt->page_start;
> + fd->function_number = pdt->function_number;
> + fd->interrupt_source_count = pdt->interrupt_source_count;
> + fd->function_version = pdt->function_version;
> +}
> +
> +#define RMI_SCAN_CONTINUE 0
> +#define RMI_SCAN_DONE 1
> +
> +static int rmi_scan_pdt_page(struct rmi_device *rmi_dev,
> + int page,
> + void *ctx,
> + int (*callback)(struct rmi_device *rmi_dev,
> + void *ctx,
> + const struct pdt_entry *entry))
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + struct pdt_entry pdt_entry;
> + u16 page_start = RMI4_PAGE_SIZE * page;
> + u16 pdt_start = page_start + PDT_START_SCAN_LOCATION;
> + u16 pdt_end = page_start + PDT_END_SCAN_LOCATION;
> + u16 addr;
> + int error;
> + int retval;
> +
> + for (addr = pdt_start; addr >= pdt_end; addr -= RMI_PDT_ENTRY_SIZE) {
> + error = rmi_read_pdt_entry(rmi_dev, &pdt_entry, addr);
> + if (error)
> + return error;
> +
> + if (RMI4_END_OF_PDT(pdt_entry.function_number))
> + break;
> +
> + retval = callback(rmi_dev, ctx, &pdt_entry);
> + if (retval != RMI_SCAN_CONTINUE)
> + return retval;
> + }
> +
> + return (data->f01_bootloader_mode || addr == pdt_start) ?
> + RMI_SCAN_DONE : RMI_SCAN_CONTINUE;
> +}
> +
> +static int rmi_scan_pdt(struct rmi_device *rmi_dev, void *ctx,
> + int (*callback)(struct rmi_device *rmi_dev,
> + void *ctx,
> + const struct pdt_entry *entry))
> +{
> + int page;
> + int retval = RMI_SCAN_DONE;
> +
> + for (page = 0; page <= RMI4_MAX_PAGE; page++) {
> + retval = rmi_scan_pdt_page(rmi_dev, page, ctx, callback);
> + if (retval != RMI_SCAN_CONTINUE)
> + break;
> + }
> +
> + return retval < 0 ? retval : 0;
> +}
> +
> +int rmi_read_register_desc(struct rmi_device *d, u16 addr,
> + struct rmi_register_descriptor *rdesc)
> +{
> + int ret;
> + u8 size_presence_reg;
> + u8 buf[35];
> + int presense_offset = 1;
> + u8 *struct_buf;
> + int reg;
> + int offset = 0;
> + int map_offset = 0;
> + int i;
> + int b;
> +
> + /*
> + * The first register of the register descriptor is the size of
> + * the register descriptor's presense register.
> + */
> + ret = rmi_read(d, addr, &size_presence_reg);
> + if (ret)
> + return ret;
> + ++addr;
> +
> + if (size_presence_reg < 0 || size_presence_reg > 35)
> + return -EIO;
> +
> + memset(buf, 0, sizeof(buf));
> +
> + /*
> + * The presence register contains the size of the register structure
> + * and a bitmap which identified which packet registers are present
> + * for this particular register type (ie query, control, or data).
> + */
> + ret = rmi_read_block(d, addr, buf, size_presence_reg);
> + if (ret)
> + return ret;
> + ++addr;
> +
> + if (buf[0] == 0) {
> + presense_offset = 3;
> + rdesc->struct_size = buf[1] | (buf[2] << 8);
> + } else {
> + rdesc->struct_size = buf[0];
> + }
> +
> + for (i = presense_offset; i < size_presence_reg; i++) {
> + for (b = 0; b < 8; b++) {
> + if (buf[i] & (0x1 << b))
> + bitmap_set(rdesc->presense_map, map_offset, 1);
> + ++map_offset;
> + }
> + }
> +
> + rdesc->num_registers = bitmap_weight(rdesc->presense_map,
> + RMI_REG_DESC_PRESENSE_BITS);
> +
> + rdesc->registers = devm_kzalloc(&d->dev, rdesc->num_registers *
> + sizeof(struct rmi_register_desc_item),
> + GFP_KERNEL);
> + if (!rdesc->registers)
> + return -ENOMEM;
> +
> + /*
> + * Allocate a temporary buffer to hold the register structure.
> + * I'm not using devm_kzalloc here since it will not be retained
> + * after exiting this function
> + */
> + struct_buf = kzalloc(rdesc->struct_size, GFP_KERNEL);
> + if (!struct_buf)
> + return -ENOMEM;
> +
> + /*
> + * The register structure contains information about every packet
> + * register of this type. This includes the size of the packet
> + * register and a bitmap of all subpackets contained in the packet
> + * register.
> + */
> + ret = rmi_read_block(d, addr, struct_buf, rdesc->struct_size);
> + if (ret)
> + goto free_struct_buff;
> +
> + reg = find_first_bit(rdesc->presense_map, RMI_REG_DESC_PRESENSE_BITS);
> + map_offset = 0;
> + for (i = 0; i < rdesc->num_registers; i++) {
> + struct rmi_register_desc_item *item = &rdesc->registers[i];
> + int reg_size = struct_buf[offset];
> +
> + ++offset;
> + if (reg_size == 0) {
> + reg_size = struct_buf[offset] |
> + (struct_buf[offset + 1] << 8);
> + offset += 2;
> + }
> +
> + if (reg_size == 0) {
> + reg_size = struct_buf[offset] |
> + (struct_buf[offset + 1] << 8) |
> + (struct_buf[offset + 2] << 16) |
> + (struct_buf[offset + 3] << 24);
> + offset += 4;
> + }
> +
> + item->reg = reg;
> + item->reg_size = reg_size;
> +
> + do {
> + for (b = 0; b < 7; b++) {
> + if (struct_buf[offset] & (0x1 << b))
> + bitmap_set(item->subpacket_map,
> + map_offset, 1);
> + ++map_offset;
> + }
> + } while (struct_buf[offset++] & 0x80);
> +
> + item->num_subpackets = bitmap_weight(item->subpacket_map,
> + RMI_REG_DESC_SUBPACKET_BITS);
> +
> + rmi_dbg(RMI_DEBUG_CORE, &d->dev,
> + "%s: reg: %d reg size: %ld subpackets: %d\n", __func__,
> + item->reg, item->reg_size, item->num_subpackets);
> +
> + reg = find_next_bit(rdesc->presense_map,
> + RMI_REG_DESC_PRESENSE_BITS, reg + 1);
> + }
> +
> +free_struct_buff:
> + kfree(struct_buf);
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(rmi_read_register_desc);
> +
> +const struct rmi_register_desc_item *rmi_get_register_desc_item(
> + struct rmi_register_descriptor *rdesc, u16 reg)
> +{
> + const struct rmi_register_desc_item *item;
> + int i;
> +
> + for (i = 0; i < rdesc->num_registers; i++) {
> + item = &rdesc->registers[i];
> + if (item->reg == reg)
> + return item;
> + }
> +
> + return NULL;
> +}
> +EXPORT_SYMBOL_GPL(rmi_get_register_desc_item);
> +
> +size_t rmi_register_desc_calc_size(struct rmi_register_descriptor *rdesc)
> +{
> + const struct rmi_register_desc_item *item;
> + int i;
> + size_t size = 0;
> +
> + for (i = 0; i < rdesc->num_registers; i++) {
> + item = &rdesc->registers[i];
> + size += item->reg_size;
> + }
> + return size;
> +}
> +EXPORT_SYMBOL_GPL(rmi_register_desc_calc_size);
> +
> +/* Compute the register offset relative to the base address */
> +int rmi_register_desc_calc_reg_offset(
> + struct rmi_register_descriptor *rdesc, u16 reg)
> +{
> + const struct rmi_register_desc_item *item;
> + int offset = 0;
> + int i;
> +
> + for (i = 0; i < rdesc->num_registers; i++) {
> + item = &rdesc->registers[i];
> + if (item->reg == reg)
> + return offset;
> + ++offset;
> + }
> + return -1;
> +}
> +EXPORT_SYMBOL_GPL(rmi_register_desc_calc_reg_offset);
> +
> +bool rmi_register_desc_has_subpacket(const struct rmi_register_desc_item *item,
> + u8 subpacket)
> +{
> + return find_next_bit(item->subpacket_map, RMI_REG_DESC_PRESENSE_BITS,
> + subpacket) == subpacket;
> +}
> +
> +/* Indicates that flash programming is enabled (bootloader mode). */
> +#define RMI_F01_STATUS_BOOTLOADER(status) (!!((status) & 0x40))
> +
> +/*
> + * Given the PDT entry for F01, read the device status register to determine
> + * if we're stuck in bootloader mode or not.
> + *
> + */
> +static int rmi_check_bootloader_mode(struct rmi_device *rmi_dev,
> + const struct pdt_entry *pdt)
> +{
> + int error;
> + u8 device_status;
> +
> + error = rmi_read(rmi_dev, pdt->data_base_addr + pdt->page_start,
> + &device_status);
> + if (error) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read device status: %d.\n", error);
> + return error;
> + }
> +
> + return RMI_F01_STATUS_BOOTLOADER(device_status);
> +}
> +
> +static int rmi_count_irqs(struct rmi_device *rmi_dev,
> + void *ctx, const struct pdt_entry *pdt)
> +{
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + int *irq_count = ctx;
> +
> + *irq_count += pdt->interrupt_source_count;
> + if (pdt->function_number == 0x01) {
> + data->f01_bootloader_mode =
> + rmi_check_bootloader_mode(rmi_dev, pdt);
> + if (data->f01_bootloader_mode)
> + dev_warn(&rmi_dev->dev,
> + "WARNING: RMI4 device is in bootloader mode!\n");
> + }
> +
> + return RMI_SCAN_CONTINUE;
> +}
> +
> +static int rmi_initial_reset(struct rmi_device *rmi_dev,
> + void *ctx, const struct pdt_entry *pdt)
> +{
> + int error;
> +
> + if (pdt->function_number == 0x01) {
> + u16 cmd_addr = pdt->page_start + pdt->command_base_addr;
> + u8 cmd_buf = RMI_DEVICE_RESET_CMD;
> + const struct rmi_device_platform_data *pdata =
> + rmi_get_platform_data(rmi_dev);
> +
> + if (rmi_dev->xport->ops->reset) {
> + error = rmi_dev->xport->ops->reset(rmi_dev->xport,
> + cmd_addr);
> + if (error)
> + return error;
> +
> + return RMI_SCAN_DONE;
> + }
> +
> + error = rmi_write_block(rmi_dev, cmd_addr, &cmd_buf, 1);
> + if (error) {
> + dev_err(&rmi_dev->dev,
> + "Initial reset failed. Code = %d.\n", error);
> + return error;
> + }
> +
> + mdelay(pdata->reset_delay_ms ?: DEFAULT_RESET_DELAY_MS);
> +
> + return RMI_SCAN_DONE;
> + }
> +
> + /* F01 should always be on page 0. If we don't find it there, fail. */
> + return pdt->page_start == 0 ? RMI_SCAN_CONTINUE : -ENODEV;
> +}
> +
> +static int rmi_create_function(struct rmi_device *rmi_dev,
> + void *ctx, const struct pdt_entry *pdt)
> +{
> + struct device *dev = &rmi_dev->dev;
> + struct rmi_driver_data *data = dev_get_drvdata(&rmi_dev->dev);
> + int *current_irq_count = ctx;
> + struct rmi_function *fn;
> + int i;
> + int error;
> +
> + rmi_dbg(RMI_DEBUG_CORE, dev, "Initializing F%02X.\n",
> + pdt->function_number);
> +
> + fn = kzalloc(sizeof(struct rmi_function) +
> + BITS_TO_LONGS(data->irq_count) * sizeof(unsigned long),
> + GFP_KERNEL);
> + if (!fn) {
> + dev_err(dev, "Failed to allocate memory for F%02X\n",
> + pdt->function_number);
> + return -ENOMEM;
> + }
> +
> + INIT_LIST_HEAD(&fn->node);
> + rmi_driver_copy_pdt_to_fd(pdt, &fn->fd);
> +
> + fn->rmi_dev = rmi_dev;
> +
> + fn->num_of_irqs = pdt->interrupt_source_count;
> + fn->irq_pos = *current_irq_count;
> + *current_irq_count += fn->num_of_irqs;
> +
> + for (i = 0; i < fn->num_of_irqs; i++)
> + set_bit(fn->irq_pos + i, fn->irq_mask);
> +
> + error = rmi_register_function(fn);
> + if (error)
> + goto err_put_fn;
> +
> + if (pdt->function_number == 0x01)
> + data->f01_container = fn;
> +
> + list_add_tail(&fn->node, &data->function_list);
> +
> + return RMI_SCAN_CONTINUE;
> +
> +err_put_fn:
> + put_device(&fn->dev);
> + return error;
> +}
> +
> +int rmi_driver_suspend(struct rmi_device *rmi_dev)
> +{
> + int retval = 0;
> +
> + retval = rmi_suspend_functions(rmi_dev);
> + if (retval)
> + dev_warn(&rmi_dev->dev, "Failed to suspend functions: %d\n",
> + retval);
> +
> + return retval;
> +}
> +EXPORT_SYMBOL_GPL(rmi_driver_suspend);
> +
> +int rmi_driver_resume(struct rmi_device *rmi_dev)
> +{
> + int retval;
> +
> + retval = rmi_resume_functions(rmi_dev);
> + if (retval)
> + dev_warn(&rmi_dev->dev, "Failed to suspend functions: %d\n",
> + retval);
> +
> + return retval;
> +}
> +EXPORT_SYMBOL_GPL(rmi_driver_resume);
> +
> +static int rmi_driver_remove(struct device *dev)
> +{
> + struct rmi_device *rmi_dev = to_rmi_device(dev);
> +
> + rmi_free_function_list(rmi_dev);
> +
> + return 0;
> +}
> +
> +static int rmi_driver_probe(struct device *dev)
> +{
> + struct rmi_driver *rmi_driver;
> + struct rmi_driver_data *data;
> + struct rmi_device_platform_data *pdata;
> + struct rmi_device *rmi_dev;
> + size_t size;
> + void *irq_memory;
> + int irq_count;
> + int retval;
> +
> + rmi_dbg(RMI_DEBUG_CORE, dev, "%s: Starting probe.\n",
> + __func__);
> +
> + if (!rmi_is_physical_device(dev)) {
> + rmi_dbg(RMI_DEBUG_CORE, dev, "Not a physical device.\n");
> + return -ENODEV;
> + }
> +
> + rmi_dev = to_rmi_device(dev);
> + rmi_driver = to_rmi_driver(dev->driver);
> + rmi_dev->driver = rmi_driver;
> +
> + pdata = rmi_get_platform_data(rmi_dev);
> +
> + data = devm_kzalloc(dev, sizeof(struct rmi_driver_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + INIT_LIST_HEAD(&data->function_list);
> + data->rmi_dev = rmi_dev;
> + dev_set_drvdata(&rmi_dev->dev, data);
> +
> + /*
> + * Right before a warm boot, the sensor might be in some unusual state,
> + * such as F54 diagnostics, or F34 bootloader mode after a firmware
> + * or configuration update. In order to clear the sensor to a known
> + * state and/or apply any updates, we issue a initial reset to clear any
> + * previous settings and force it into normal operation.
> + *
> + * We have to do this before actually building the PDT because
> + * the reflash updates (if any) might cause various registers to move
> + * around.
> + *
> + * For a number of reasons, this initial reset may fail to return
> + * within the specified time, but we'll still be able to bring up the
> + * driver normally after that failure. This occurs most commonly in
> + * a cold boot situation (where then firmware takes longer to come up
> + * than from a warm boot) and the reset_delay_ms in the platform data
> + * has been set too short to accommodate that. Since the sensor will
> + * eventually come up and be usable, we don't want to just fail here
> + * and leave the customer's device unusable. So we warn them, and
> + * continue processing.
> + */
> + retval = rmi_scan_pdt(rmi_dev, NULL, rmi_initial_reset);
> + if (retval < 0)
> + dev_warn(dev, "RMI initial reset failed! Continuing in spite of this.\n");
> +
> + retval = rmi_read(rmi_dev, PDT_PROPERTIES_LOCATION, &data->pdt_props);
> + if (retval < 0) {
> + /*
> + * we'll print out a warning and continue since
> + * failure to get the PDT properties is not a cause to fail
> + */
> + dev_warn(dev, "Could not read PDT properties from %#06x (code %d). Assuming 0x00.\n",
> + PDT_PROPERTIES_LOCATION, retval);
> + }
> +
> + /*
> + * We need to count the IRQs and allocate their storage before scanning
> + * the PDT and creating the function entries, because adding a new
> + * function can trigger events that result in the IRQ related storage
> + * being accessed.
> + */
> + rmi_dbg(RMI_DEBUG_CORE, dev, "Counting IRQs.\n");
> + irq_count = 0;
> + retval = rmi_scan_pdt(rmi_dev, &irq_count, rmi_count_irqs);
> + if (retval < 0) {
> + dev_err(dev, "IRQ counting failed with code %d.\n", retval);
> + goto err;
> + }
> + data->irq_count = irq_count;
> + data->num_of_irq_regs = (data->irq_count + 7) / 8;
> +
> + mutex_init(&data->irq_mutex);
> +
> + size = BITS_TO_LONGS(data->irq_count) * sizeof(unsigned long);
> + irq_memory = devm_kzalloc(dev, size * 4, GFP_KERNEL);
> + if (!irq_memory) {
> + dev_err(dev, "Failed to allocate memory for irq masks.\n");
> + goto err;
> + }
> +
> + data->irq_status = irq_memory + size * 0;
> + data->fn_irq_bits = irq_memory + size * 1;
> + data->current_irq_mask = irq_memory + size * 2;
> + data->new_irq_mask = irq_memory + size * 3;
> +
> + if (rmi_dev->xport->input) {
> + /*
> + * The transport driver already has an input device.
> + * In some cases it is preferable to reuse the transport
> + * devices input device instead of creating a new one here.
> + * One example is some HID touchpads report "pass-through"
> + * button events are not reported by rmi registers.
> + */
> + data->input = rmi_dev->xport->input;
> + } else {
> + data->input = devm_input_allocate_device(dev);
> + if (!data->input) {
> + dev_err(dev, "%s: Failed to allocate input device.\n",
> + __func__);
> + retval = -ENOMEM;
> + goto err_destroy_functions;
> + }
> + rmi_driver_set_input_params(rmi_dev, data->input);
> + data->input->phys = devm_kasprintf(dev, GFP_KERNEL,
> + "%s/input0", dev_name(dev));
> + }
> +
> + irq_count = 0;
> + rmi_dbg(RMI_DEBUG_CORE, dev, "Creating functions.");
> + retval = rmi_scan_pdt(rmi_dev, &irq_count, rmi_create_function);
> + if (retval < 0) {
> + dev_err(dev, "Function creation failed with code %d.\n",
> + retval);
> + goto err_destroy_functions;
> + }
> +
> + if (!data->f01_container) {
> + dev_err(dev, "Missing F01 container!\n");
> + retval = -EINVAL;
> + goto err_destroy_functions;
> + }
> +
> + retval = rmi_read_block(rmi_dev,
> + data->f01_container->fd.control_base_addr + 1,
> + data->current_irq_mask, data->num_of_irq_regs);
> + if (retval < 0) {
> + dev_err(dev, "%s: Failed to read current IRQ mask.\n",
> + __func__);
> + goto err_destroy_functions;
> + }
> +
> + if (data->input) {
> + rmi_driver_set_input_name(rmi_dev, data->input);
> + if (!rmi_dev->xport->input) {
> + if (input_register_device(data->input)) {
> + dev_err(dev, "%s: Failed to register input device.\n",
> + __func__);
> + goto err_destroy_functions;
> + }
> + }
> + }
> +
> + if (data->f01_container->dev.driver)
> + /* Driver already bound, so enable ATTN now. */
> + return enable_sensor(rmi_dev);
> +
> + return 0;
> +
> +err_destroy_functions:
> + rmi_free_function_list(rmi_dev);
> +err:
> + return retval < 0 ? retval : 0;
> +}
> +
> +static struct rmi_driver rmi_physical_driver = {
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = "rmi4_physical",
> + .bus = &rmi_bus_type,
> + .probe = rmi_driver_probe,
> + .remove = rmi_driver_remove,
> + },
> + .reset_handler = rmi_driver_reset_handler,
> + .clear_irq_bits = rmi_driver_clear_irq_bits,
> + .set_irq_bits = rmi_driver_set_irq_bits,
> + .set_input_params = rmi_driver_set_input_params,
> +};
> +
> +bool rmi_is_physical_driver(struct device_driver *drv)
> +{
> + return drv == &rmi_physical_driver.driver;
> +}
> +
> +int __init rmi_register_physical_driver(void)
> +{
> + int error;
> +
> + error = driver_register(&rmi_physical_driver.driver);
> + if (error) {
> + pr_err("%s: driver register failed, code=%d.\n", __func__,
> + error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +void __exit rmi_unregister_physical_driver(void)
> +{
> + driver_unregister(&rmi_physical_driver.driver);
> +}
> diff --git a/drivers/input/rmi4/rmi_driver.h b/drivers/input/rmi4/rmi_driver.h
> new file mode 100644
> index 0000000..bc87c09
> --- /dev/null
> +++ b/drivers/input/rmi4/rmi_driver.h
> @@ -0,0 +1,103 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#ifndef _RMI_DRIVER_H
> +#define _RMI_DRIVER_H
> +
> +#include <linux/ctype.h>
> +#include <linux/hrtimer.h>
> +#include <linux/ktime.h>
> +#include <linux/input.h>
> +#include "rmi_bus.h"
> +
> +#define RMI_DRIVER_VERSION "2.0"
> +
> +#define SYNAPTICS_INPUT_DEVICE_NAME "Synaptics RMI4 Touch Sensor"
> +#define SYNAPTICS_VENDOR_ID 0x06cb
> +
> +#define GROUP(_attrs) { \
> + .attrs = _attrs, \
> +}
> +
> +#define PDT_PROPERTIES_LOCATION 0x00EF
> +#define BSR_LOCATION 0x00FE
> +
> +#define RMI_PDT_PROPS_HAS_BSR 0x02
> +
> +#define NAME_BUFFER_SIZE 256
> +
> +#define RMI_PDT_ENTRY_SIZE 6
> +#define RMI_PDT_FUNCTION_VERSION_MASK 0x60
> +#define RMI_PDT_INT_SOURCE_COUNT_MASK 0x07
> +
> +#define PDT_START_SCAN_LOCATION 0x00e9
> +#define PDT_END_SCAN_LOCATION 0x0005
> +#define RMI4_END_OF_PDT(id) ((id) == 0x00 || (id) == 0xff)
> +
> +struct pdt_entry {
> + u16 page_start;
> + u8 query_base_addr;
> + u8 command_base_addr;
> + u8 control_base_addr;
> + u8 data_base_addr;
> + u8 interrupt_source_count;
> + u8 function_version;
> + u8 function_number;
> +};
> +
> +int rmi_read_pdt_entry(struct rmi_device *rmi_dev, struct pdt_entry *entry,
> + u16 pdt_address);
> +
> +#define RMI_REG_DESC_PRESENSE_BITS (32 * BITS_PER_BYTE)
> +#define RMI_REG_DESC_SUBPACKET_BITS (37 * BITS_PER_BYTE)
> +
> +/* describes a single packet register */
> +struct rmi_register_desc_item {
> + u16 reg;
> + unsigned long reg_size;
> + u8 num_subpackets;
> + unsigned long subpacket_map[BITS_TO_LONGS(
> + RMI_REG_DESC_SUBPACKET_BITS)];
> +};
> +
> +/*
> + * describes the packet registers for a particular type
> + * (ie query, control, data)
> + */
> +struct rmi_register_descriptor {
> + unsigned long struct_size;
> + unsigned long presense_map[BITS_TO_LONGS(RMI_REG_DESC_PRESENSE_BITS)];
> + u8 num_registers;
> + struct rmi_register_desc_item *registers;
> +};
> +
> +int rmi_read_register_desc(struct rmi_device *d, u16 addr,
> + struct rmi_register_descriptor *rdesc);
> +const struct rmi_register_desc_item *rmi_get_register_desc_item(
> + struct rmi_register_descriptor *rdesc, u16 reg);
> +
> +/*
> + * Calculate the total size of all of the registers described in the
> + * descriptor.
> + */
> +size_t rmi_register_desc_calc_size(struct rmi_register_descriptor *rdesc);
> +int rmi_register_desc_calc_reg_offset(
> + struct rmi_register_descriptor *rdesc, u16 reg);
> +bool rmi_register_desc_has_subpacket(const struct rmi_register_desc_item *item,
> + u8 subpacket);
> +
> +bool rmi_is_physical_driver(struct device_driver *);
> +int rmi_register_physical_driver(void);
> +void rmi_unregister_physical_driver(void);
> +
> +char *rmi_f01_get_product_ID(struct rmi_function *fn);
> +
> +extern struct rmi_function_handler rmi_f01_handler;
> +
> +#endif
> diff --git a/drivers/input/rmi4/rmi_f01.c b/drivers/input/rmi4/rmi_f01.c
> new file mode 100644
> index 0000000..09fb20b
> --- /dev/null
> +++ b/drivers/input/rmi4/rmi_f01.c
> @@ -0,0 +1,575 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/kconfig.h>
> +#include <linux/rmi.h>
> +#include <linux/slab.h>
> +#include <linux/uaccess.h>
> +#include <linux/of.h>
> +#include "rmi_driver.h"
> +
> +#define RMI_PRODUCT_ID_LENGTH 10
> +#define RMI_PRODUCT_INFO_LENGTH 2
> +
> +#define RMI_DATE_CODE_LENGTH 3
> +
> +#define PRODUCT_ID_OFFSET 0x10
> +#define PRODUCT_INFO_OFFSET 0x1E
> +
> +
> +/* Force a firmware reset of the sensor */
> +#define RMI_F01_CMD_DEVICE_RESET 1
> +
> +/* Various F01_RMI_QueryX bits */
> +
> +#define RMI_F01_QRY1_CUSTOM_MAP BIT(0)
> +#define RMI_F01_QRY1_NON_COMPLIANT BIT(1)
> +#define RMI_F01_QRY1_HAS_LTS BIT(2)
> +#define RMI_F01_QRY1_HAS_SENSOR_ID BIT(3)
> +#define RMI_F01_QRY1_HAS_CHARGER_INP BIT(4)
> +#define RMI_F01_QRY1_HAS_ADJ_DOZE BIT(5)
> +#define RMI_F01_QRY1_HAS_ADJ_DOZE_HOFF BIT(6)
> +#define RMI_F01_QRY1_HAS_QUERY42 BIT(7)
> +
> +#define RMI_F01_QRY5_YEAR_MASK 0x1f
> +#define RMI_F01_QRY6_MONTH_MASK 0x0f
> +#define RMI_F01_QRY7_DAY_MASK 0x1f
> +
> +#define RMI_F01_QRY2_PRODINFO_MASK 0x7f
> +
> +#define RMI_F01_BASIC_QUERY_LEN 21 /* From Query 00 through 20 */
> +
> +struct f01_basic_properties {
> + u8 manufacturer_id;
> + bool has_lts;
> + bool has_adjustable_doze;
> + bool has_adjustable_doze_holdoff;
> + char dom[11]; /* YYYY/MM/DD + '\0' */
> + u8 product_id[RMI_PRODUCT_ID_LENGTH + 1];
> + u16 productinfo;
> + u32 firmware_id;
> +};
> +
> +/* F01 device status bits */
> +
> +/* Most recent device status event */
> +#define RMI_F01_STATUS_CODE(status) ((status) & 0x0f)
> +/* The device has lost its configuration for some reason. */
> +#define RMI_F01_STATUS_UNCONFIGURED(status) (!!((status) & 0x80))
> +
> +/* Control register bits */
> +
> +/*
> + * Sleep mode controls power management on the device and affects all
> + * functions of the device.
> + */
> +#define RMI_F01_CTRL0_SLEEP_MODE_MASK 0x03
> +
> +#define RMI_SLEEP_MODE_NORMAL 0x00
> +#define RMI_SLEEP_MODE_SENSOR_SLEEP 0x01
> +#define RMI_SLEEP_MODE_RESERVED0 0x02
> +#define RMI_SLEEP_MODE_RESERVED1 0x03
> +
> +/*
> + * This bit disables whatever sleep mode may be selected by the sleep_mode
> + * field and forces the device to run at full power without sleeping.
> + */
> +#define RMI_F01_CRTL0_NOSLEEP_BIT BIT(2)
> +
> +/*
> + * When this bit is set, the touch controller employs a noise-filtering
> + * algorithm designed for use with a connected battery charger.
> + */
> +#define RMI_F01_CRTL0_CHARGER_BIT BIT(5)
> +
> +/*
> + * Sets the report rate for the device. The effect of this setting is
> + * highly product dependent. Check the spec sheet for your particular
> + * touch sensor.
> + */
> +#define RMI_F01_CRTL0_REPORTRATE_BIT BIT(6)
> +
> +/*
> + * Written by the host as an indicator that the device has been
> + * successfully configured.
> + */
> +#define RMI_F01_CRTL0_CONFIGURED_BIT BIT(7)
> +
> +/**
> + * @ctrl0 - see the bit definitions above.
> + * @doze_interval - controls the interval between checks for finger presence
> + * when the touch sensor is in doze mode, in units of 10ms.
> + * @wakeup_threshold - controls the capacitance threshold at which the touch
> + * sensor will decide to wake up from that low power state.
> + * @doze_holdoff - controls how long the touch sensor waits after the last
> + * finger lifts before entering the doze state, in units of 100ms.
> + */
> +struct f01_device_control {
> + u8 ctrl0;
> + u8 doze_interval;
> + u8 wakeup_threshold;
> + u8 doze_holdoff;
> +};
> +
> +struct f01_data {
> + struct f01_basic_properties properties;
> + struct f01_device_control device_control;
> +
> + u16 doze_interval_addr;
> + u16 wakeup_threshold_addr;
> + u16 doze_holdoff_addr;
> +
> + bool suspended;
> + bool old_nosleep;
> +
> + unsigned int num_of_irq_regs;
> +};
> +
> +static int rmi_f01_read_properties(struct rmi_device *rmi_dev,
> + u16 query_base_addr,
> + struct f01_basic_properties *props)
> +{
> + u8 queries[RMI_F01_BASIC_QUERY_LEN];
> + int ret;
> + int query_offset = query_base_addr;
> + bool has_ds4_queries = false;
> + bool has_query42 = false;
> + bool has_sensor_id = false;
> + bool has_package_id_query = false;
> + bool has_build_id_query = false;
> + u16 prod_info_addr;
> + u8 ds4_query_len;
> +
> + ret = rmi_read_block(rmi_dev, query_offset,
> + queries, RMI_F01_BASIC_QUERY_LEN);
> + if (ret) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read device query registers: %d\n", ret);
> + return ret;
> + }
> +
> + prod_info_addr = query_offset + 17;
> + query_offset += RMI_F01_BASIC_QUERY_LEN;
> +
> + /* Now parse what we got */
> + props->manufacturer_id = queries[0];
> +
> + props->has_lts = queries[1] & RMI_F01_QRY1_HAS_LTS;
> + props->has_adjustable_doze =
> + queries[1] & RMI_F01_QRY1_HAS_ADJ_DOZE;
> + props->has_adjustable_doze_holdoff =
> + queries[1] & RMI_F01_QRY1_HAS_ADJ_DOZE_HOFF;
> + has_query42 = queries[1] & RMI_F01_QRY1_HAS_QUERY42;
> + has_sensor_id = queries[1] & RMI_F01_QRY1_HAS_SENSOR_ID;
> +
> + snprintf(props->dom, sizeof(props->dom), "20%02d/%02d/%02d",
> + queries[5] & RMI_F01_QRY5_YEAR_MASK,
> + queries[6] & RMI_F01_QRY6_MONTH_MASK,
> + queries[7] & RMI_F01_QRY7_DAY_MASK);
> +
> + memcpy(props->product_id, &queries[11],
> + RMI_PRODUCT_ID_LENGTH);
> + props->product_id[RMI_PRODUCT_ID_LENGTH] = '\0';
> +
> + props->productinfo =
> + ((queries[2] & RMI_F01_QRY2_PRODINFO_MASK) << 7) |
> + (queries[3] & RMI_F01_QRY2_PRODINFO_MASK);
> +
> + if (has_sensor_id)
> + query_offset++;
> +
> + if (has_query42) {
> + ret = rmi_read(rmi_dev, query_offset, queries);
> + if (ret) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read query 42 register: %d\n", ret);
> + return ret;
> + }
> +
> + has_ds4_queries = !!(queries[0] & BIT(0));
> + query_offset++;
> + }
> +
> + if (has_ds4_queries) {
> + ret = rmi_read(rmi_dev, query_offset, &ds4_query_len);
> + if (ret) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read DS4 queries length: %d\n", ret);
> + return ret;
> + }
> + query_offset++;
> +
> + if (ds4_query_len > 0) {
> + ret = rmi_read(rmi_dev, query_offset, queries);
> + if (ret) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read DS4 queries: %d\n",
> + ret);
> + return ret;
> + }
> +
> + has_package_id_query = !!(queries[0] & BIT(0));
> + has_build_id_query = !!(queries[0] & BIT(1));
> + }
> +
> + if (has_package_id_query)
> + prod_info_addr++;
> +
> + if (has_build_id_query) {
> + ret = rmi_read_block(rmi_dev, prod_info_addr, queries,
> + 3);
> + if (ret) {
> + dev_err(&rmi_dev->dev,
> + "Failed to read product info: %d\n",
> + ret);
> + return ret;
> + }
> +
> + props->firmware_id = queries[1] << 8 | queries[0];
> + props->firmware_id += queries[2] * 65536;
> + }
> + }
> +
> + return 0;
> +}
> +
> +char *rmi_f01_get_product_ID(struct rmi_function *fn)
> +{
> + struct f01_data *f01 = dev_get_drvdata(&fn->dev);
> +
> + return f01->properties.product_id;
> +}
> +
> +static int rmi_f01_probe(struct rmi_function *fn)
> +{
> + struct rmi_device *rmi_dev = fn->rmi_dev;
> + struct rmi_driver_data *driver_data = dev_get_drvdata(&rmi_dev->dev);
> + struct rmi_device_platform_data *pdata = rmi_get_platform_data(rmi_dev);
> + struct f01_data *f01;
> + int error;
> + u16 ctrl_base_addr = fn->fd.control_base_addr;
> + u8 device_status;
> + u8 temp;
> +
> + f01 = devm_kzalloc(&fn->dev, sizeof(struct f01_data), GFP_KERNEL);
> + if (!f01)
> + return -ENOMEM;
> +
> + f01->num_of_irq_regs = driver_data->num_of_irq_regs;
> +
> + /*
> + * Set the configured bit and (optionally) other important stuff
> + * in the device control register.
> + */
> +
> + error = rmi_read(rmi_dev, fn->fd.control_base_addr,
> + &f01->device_control.ctrl0);
> + if (error) {
> + dev_err(&fn->dev, "Failed to read F01 control: %d\n", error);
> + return error;
> + }
> +
> + switch (pdata->power_management.nosleep) {
> + case RMI_F01_NOSLEEP_DEFAULT:
> + break;
> + case RMI_F01_NOSLEEP_OFF:
> + f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
> + break;
> + case RMI_F01_NOSLEEP_ON:
> + f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
> + break;
> + }
> +
> + /*
> + * Sleep mode might be set as a hangover from a system crash or
> + * reboot without power cycle. If so, clear it so the sensor
> + * is certain to function.
> + */
> + if ((f01->device_control.ctrl0 & RMI_F01_CTRL0_SLEEP_MODE_MASK) !=
> + RMI_SLEEP_MODE_NORMAL) {
> + dev_warn(&fn->dev,
> + "WARNING: Non-zero sleep mode found. Clearing...\n");
> + f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
> + }
> +
> + f01->device_control.ctrl0 |= RMI_F01_CRTL0_CONFIGURED_BIT;
> +
> + error = rmi_write(rmi_dev, fn->fd.control_base_addr,
> + f01->device_control.ctrl0);
> + if (error) {
> + dev_err(&fn->dev, "Failed to write F01 control: %d\n", error);
> + return error;
> + }
> +
> + /* Dummy read in order to clear irqs */
> + error = rmi_read(rmi_dev, fn->fd.data_base_addr + 1, &temp);
> + if (error < 0) {
> + dev_err(&fn->dev, "Failed to read Interrupt Status.\n");
> + return error;
> + }
> +
> + error = rmi_f01_read_properties(rmi_dev, fn->fd.query_base_addr,
> + &f01->properties);
> + if (error < 0) {
> + dev_err(&fn->dev, "Failed to read F01 properties.\n");
> + return error;
> + }
> +
> + dev_info(&fn->dev, "found RMI device, manufacturer: %s, product: %s, fw id: %d\n",
> + f01->properties.manufacturer_id == 1 ? "Synaptics" : "unknown",
> + f01->properties.product_id, f01->properties.firmware_id);
> +
> + /* Advance to interrupt control registers, then skip over them. */
> + ctrl_base_addr++;
> + ctrl_base_addr += f01->num_of_irq_regs;
> +
> + /* read control register */
> + if (f01->properties.has_adjustable_doze) {
> + f01->doze_interval_addr = ctrl_base_addr;
> + ctrl_base_addr++;
> +
> +
> + if (pdata->power_management.doze_interval) {
> + f01->device_control.doze_interval =
> + pdata->power_management.doze_interval;
> + error = rmi_write(rmi_dev, f01->doze_interval_addr,
> + f01->device_control.doze_interval);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to configure F01 doze interval register: %d\n",
> + error);
> + return error;
> + }
> + } else {
> + error = rmi_read(rmi_dev, f01->doze_interval_addr,
> + &f01->device_control.doze_interval);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to read F01 doze interval register: %d\n",
> + error);
> + return error;
> + }
> + }
> +
> + f01->wakeup_threshold_addr = ctrl_base_addr;
> + ctrl_base_addr++;
> +
> + if (pdata->power_management.wakeup_threshold) {
> + f01->device_control.wakeup_threshold =
> + pdata->power_management.wakeup_threshold;
> + error = rmi_write(rmi_dev, f01->wakeup_threshold_addr,
> + f01->device_control.wakeup_threshold);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to configure F01 wakeup threshold register: %d\n",
> + error);
> + return error;
> + }
> + } else {
> + error = rmi_read(rmi_dev, f01->wakeup_threshold_addr,
> + &f01->device_control.wakeup_threshold);
> + if (error < 0) {
> + dev_err(&fn->dev,
> + "Failed to read F01 wakeup threshold register: %d\n",
> + error);
> + return error;
> + }
> + }
> + }
> +
> + if (f01->properties.has_lts)
> + ctrl_base_addr++;
> +
> + if (f01->properties.has_adjustable_doze_holdoff) {
> + f01->doze_holdoff_addr = ctrl_base_addr;
> + ctrl_base_addr++;
> +
> + if (pdata->power_management.doze_holdoff) {
> + f01->device_control.doze_holdoff =
> + pdata->power_management.doze_holdoff;
> + error = rmi_write(rmi_dev, f01->doze_holdoff_addr,
> + f01->device_control.doze_holdoff);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to configure F01 doze holdoff register: %d\n",
> + error);
> + return error;
> + }
> + } else {
> + error = rmi_read(rmi_dev, f01->doze_holdoff_addr,
> + &f01->device_control.doze_holdoff);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to read F01 doze holdoff register: %d\n",
> + error);
> + return error;
> + }
> + }
> + }
> +
> + error = rmi_read(rmi_dev, fn->fd.data_base_addr, &device_status);
> + if (error < 0) {
> + dev_err(&fn->dev,
> + "Failed to read device status: %d\n", error);
> + return error;
> + }
> +
> + if (RMI_F01_STATUS_UNCONFIGURED(device_status)) {
> + dev_err(&fn->dev,
> + "Device was reset during configuration process, status: %#02x!\n",
> + RMI_F01_STATUS_CODE(device_status));
> + return -EINVAL;
> + }
> +
> + dev_set_drvdata(&fn->dev, f01);
> +
> + return 0;
> +}
> +
> +static int rmi_f01_config(struct rmi_function *fn)
> +{
> + struct f01_data *f01 = dev_get_drvdata(&fn->dev);
> + int error;
> +
> + error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
> + f01->device_control.ctrl0);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to write device_control register: %d\n", error);
> + return error;
> + }
> +
> + if (f01->properties.has_adjustable_doze) {
> + error = rmi_write(fn->rmi_dev, f01->doze_interval_addr,
> + f01->device_control.doze_interval);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to write doze interval: %d\n", error);
> + return error;
> + }
> +
> + error = rmi_write_block(fn->rmi_dev,
> + f01->wakeup_threshold_addr,
> + &f01->device_control.wakeup_threshold,
> + sizeof(u8));
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to write wakeup threshold: %d\n",
> + error);
> + return error;
> + }
> + }
> +
> + if (f01->properties.has_adjustable_doze_holdoff) {
> + error = rmi_write(fn->rmi_dev, f01->doze_holdoff_addr,
> + f01->device_control.doze_holdoff);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to write doze holdoff: %d\n", error);
> + return error;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_f01_suspend(struct rmi_function *fn)
> +{
> + struct f01_data *f01 = dev_get_drvdata(&fn->dev);
> + int error;
> +
> + f01->old_nosleep =
> + f01->device_control.ctrl0 & RMI_F01_CRTL0_NOSLEEP_BIT;
> + f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
> +
> + f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
> + if (device_may_wakeup(fn->rmi_dev->xport->dev))
> + f01->device_control.ctrl0 |= RMI_SLEEP_MODE_RESERVED1;
> + else
> + f01->device_control.ctrl0 |= RMI_SLEEP_MODE_SENSOR_SLEEP;
> +
> + error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
> + f01->device_control.ctrl0);
> + if (error) {
> + dev_err(&fn->dev, "Failed to write sleep mode: %d.\n", error);
> + if (f01->old_nosleep)
> + f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
> + f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
> + f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_f01_resume(struct rmi_function *fn)
> +{
> + struct f01_data *f01 = dev_get_drvdata(&fn->dev);
> + int error;
> +
> + if (f01->old_nosleep)
> + f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
> +
> + f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
> + f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
> +
> + error = rmi_write(fn->rmi_dev, fn->fd.control_base_addr,
> + f01->device_control.ctrl0);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to restore normal operation: %d.\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_f01_attention(struct rmi_function *fn,
> + unsigned long *irq_bits)
> +{
> + struct rmi_device *rmi_dev = fn->rmi_dev;
> + int error;
> + u8 device_status;
> +
> + error = rmi_read(rmi_dev, fn->fd.data_base_addr, &device_status);
> + if (error) {
> + dev_err(&fn->dev,
> + "Failed to read device status: %d.\n", error);
> + return error;
> + }
> +
> + if (RMI_F01_STATUS_UNCONFIGURED(device_status)) {
> + dev_warn(&fn->dev, "Device reset detected.\n");
> + error = rmi_dev->driver->reset_handler(rmi_dev);
> + if (error) {
> + dev_err(&fn->dev, "Device reset failed: %d\n", error);
> + return error;
> + }
> + }
> +
> + return 0;
> +}
> +
> +struct rmi_function_handler rmi_f01_handler = {
> + .driver = {
> + .name = "rmi4_f01",
> + /*
> + * Do not allow user unbinding F01 as it is critical
> + * function.
> + */
> + .suppress_bind_attrs = true,
> + },
> + .func = 0x01,
> + .probe = rmi_f01_probe,
> + .config = rmi_f01_config,
> + .attention = rmi_f01_attention,
> + .suspend = rmi_f01_suspend,
> + .resume = rmi_f01_resume,
> +};
> diff --git a/include/linux/rmi.h b/include/linux/rmi.h
> new file mode 100644
> index 0000000..c559c48
> --- /dev/null
> +++ b/include/linux/rmi.h
> @@ -0,0 +1,213 @@
> +/*
> + * Copyright (c) 2011-2015 Synaptics Incorporated
> + * Copyright (c) 2011 Unixphere
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#ifndef _RMI_H
> +#define _RMI_H
> +#include <linux/kernel.h>
> +#include <linux/device.h>
> +#include <linux/interrupt.h>
> +#include <linux/input.h>
> +#include <linux/list.h>
> +#include <linux/module.h>
> +#include <linux/types.h>
> +
> +#define NAME_BUFFER_SIZE 256
> +
> +/**
> + * struct rmi_f01_power - override default power management settings.
> + *
> + */
> +enum rmi_f01_nosleep {
> + RMI_F01_NOSLEEP_DEFAULT = 0,
> + RMI_F01_NOSLEEP_OFF = 1,
> + RMI_F01_NOSLEEP_ON = 2
> +};
> +
> +/**
> + * struct rmi_f01_power_management -When non-zero, these values will be written
> + * to the touch sensor to override the default firmware settigns. For a
> + * detailed explanation of what each field does, see the corresponding
> + * documention in the RMI4 specification.
> + *
> + * @nosleep - specifies whether the device is permitted to sleep or doze (that
> + * is, enter a temporary low power state) when no fingers are touching the
> + * sensor.
> + * @wakeup_threshold - controls the capacitance threshold at which the touch
> + * sensor will decide to wake up from that low power state.
> + * @doze_holdoff - controls how long the touch sensor waits after the last
> + * finger lifts before entering the doze state, in units of 100ms.
> + * @doze_interval - controls the interval between checks for finger presence
> + * when the touch sensor is in doze mode, in units of 10ms.
> + */
> +struct rmi_f01_power_management {
> + enum rmi_f01_nosleep nosleep;
> + u8 wakeup_threshold;
> + u8 doze_holdoff;
> + u8 doze_interval;
> +};
> +
> +/**
> + * struct rmi_device_platform_data - system specific configuration info.
> + *
> + * @irq_flags - this is used to specify intrerrupt type flags.
> + *
> + * @reset_delay_ms - after issuing a reset command to the touch sensor, the
> + * driver waits a few milliseconds to give the firmware a chance to
> + * to re-initialize. You can override the default wait period here.
> + */
> +struct rmi_device_platform_data {
> + int irq_flags;
> +
> + int reset_delay_ms;
> +
> + /* function handler pdata */
> + struct rmi_f01_power_management power_management;
> +};
> +
> +/**
> + * struct rmi_function_descriptor - RMI function base addresses
> + *
> + * @query_base_addr: The RMI Query base address
> + * @command_base_addr: The RMI Command base address
> + * @control_base_addr: The RMI Control base address
> + * @data_base_addr: The RMI Data base address
> + * @interrupt_source_count: The number of irqs this RMI function needs
> + * @function_number: The RMI function number
> + *
> + * This struct is used when iterating the Page Description Table. The addresses
> + * are 16-bit values to include the current page address.
> + *
> + */
> +struct rmi_function_descriptor {
> + u16 query_base_addr;
> + u16 command_base_addr;
> + u16 control_base_addr;
> + u16 data_base_addr;
> + u8 interrupt_source_count;
> + u8 function_number;
> + u8 function_version;
> +};
> +
> +struct rmi_device;
> +
> +/**
> + * struct rmi_transport_dev - represent an RMI transport device
> + *
> + * @dev: Pointer to the communication device, e.g. i2c or spi
> + * @rmi_dev: Pointer to the RMI device
> + * @proto_name: name of the transport protocol (SPI, i2c, etc)
> + * @ops: pointer to transport operations implementation
> + *
> + * The RMI transport device implements the glue between different communication
> + * buses such as I2C and SPI.
> + *
> + */
> +struct rmi_transport_dev {
> + struct device *dev;
> + struct rmi_device *rmi_dev;
> +
> + const char *proto_name;
> + const struct rmi_transport_ops *ops;
> +
> + struct rmi_device_platform_data pdata;
> +
> + struct input_dev *input;
> +
> + void *attn_data;
> + int attn_size;
> +};
> +
> +/**
> + * struct rmi_transport_ops - defines transport protocol operations.
> + *
> + * @write_block: Writing a block of data to the specified address
> + * @read_block: Read a block of data from the specified address.
> + */
> +struct rmi_transport_ops {
> + int (*write_block)(struct rmi_transport_dev *xport, u16 addr,
> + const void *buf, size_t len);
> + int (*read_block)(struct rmi_transport_dev *xport, u16 addr,
> + void *buf, size_t len);
> + int (*reset)(struct rmi_transport_dev *xport, u16 reset_addr);
> +};
> +
> +/**
> + * struct rmi_driver - driver for an RMI4 sensor on the RMI bus.
> + *
> + * @driver: Device driver model driver
> + * @reset_handler: Called when a reset is detected.
> + * @clear_irq_bits: Clear the specified bits in the current interrupt mask.
> + * @set_irq_bist: Set the specified bits in the current interrupt mask.
> + * @store_productid: Callback for cache product id from function 01
> + * @data: Private data pointer
> + *
> + */
> +struct rmi_driver {
> + struct device_driver driver;
> +
> + int (*reset_handler)(struct rmi_device *rmi_dev);
> + int (*clear_irq_bits)(struct rmi_device *rmi_dev, unsigned long *mask);
> + int (*set_irq_bits)(struct rmi_device *rmi_dev, unsigned long *mask);
> + int (*store_productid)(struct rmi_device *rmi_dev);
> + int (*set_input_params)(struct rmi_device *rmi_dev,
> + struct input_dev *input);
> + void *data;
> +};
> +
> +/**
> + * struct rmi_device - represents an RMI4 sensor device on the RMI bus.
> + *
> + * @dev: The device created for the RMI bus
> + * @number: Unique number for the device on the bus.
> + * @driver: Pointer to associated driver
> + * @xport: Pointer to the transport interface
> + *
> + */
> +struct rmi_device {
> + struct device dev;
> + int number;
> +
> + struct rmi_driver *driver;
> + struct rmi_transport_dev *xport;
> +
> +};
> +
> +struct rmi_driver_data {
> + struct list_head function_list;
> +
> + struct rmi_device *rmi_dev;
> +
> + struct rmi_function *f01_container;
> + bool f01_bootloader_mode;
> +
> + u32 attn_count;
> + int num_of_irq_regs;
> + int irq_count;
> + unsigned long *irq_status;
> + unsigned long *fn_irq_bits;
> + unsigned long *current_irq_mask;
> + unsigned long *new_irq_mask;
> + struct mutex irq_mutex;
> + struct input_dev *input;
> +
> + u8 pdt_props;
> + u8 bsr;
> +
> + bool enabled;
> +
> + void *data;
> +};
> +
> +int rmi_register_transport_device(struct rmi_transport_dev *xport);
> +void rmi_unregister_transport_device(struct rmi_transport_dev *xport);
> +int rmi_process_interrupt_requests(struct rmi_device *rmi_dev);
> +
> +int rmi_driver_suspend(struct rmi_device *rmi_dev);
> +int rmi_driver_resume(struct rmi_device *rmi_dev);
> +#endif
> diff --git a/include/uapi/linux/input.h b/include/uapi/linux/input.h
> index 2758687..0111384 100644
> --- a/include/uapi/linux/input.h
> +++ b/include/uapi/linux/input.h
> @@ -246,6 +246,7 @@ struct input_mask {
> #define BUS_GSC 0x1A
> #define BUS_ATARI 0x1B
> #define BUS_SPI 0x1C
> +#define BUS_RMI 0x1D
>
> /*
> * MT_TOOL types
> --
> 2.5.0
>
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
