Re: [PATCH] Staging: ste_rmi4: Remove obsolete driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Shraddha,

On Sat, Dec 26, 2015 at 7:23 AM,  <shraddha.6596@xxxxxxxxx> wrote:
> From: Shraddha Barke <shraddha.6596@xxxxxxxxx>
>
> Remove support for Synaptics RMI4 Touchscreen driver from the staging
> directory since support for Synaptics RMI4 touchpads has been added
> in the mainline kernel.
> commit 9fb6bf02e3ad ("HID: rmi: introduce RMI driver for Synaptics touchpads")
>

The driver in the commit you referenced only supports HID RMI4
devices. While the ste_rmi4 driver only supports touchscreens which
are connected with I2C directly. Currently, their is not a driver in
the mainline kernel which supports RMI / I2C devices. However, I did
just post a v2 for a patch series which would add support for RMI4
several different protocols I2C, HID, SPI, and potentially others.

Hopefully, there will soon be a mainline replacement for this driver.
But, I just wanted to point out that currently there is not.

Andrew

> Signed-off-by: Shraddha Barke <shraddha.6596@xxxxxxxxx>
> ---
>  drivers/staging/Kconfig                       |    2 -
>  drivers/staging/Makefile                      |    1 -
>  drivers/staging/ste_rmi4/Kconfig              |    9 -
>  drivers/staging/ste_rmi4/Makefile             |    4 -
>  drivers/staging/ste_rmi4/TODO                 |    7 -
>  drivers/staging/ste_rmi4/synaptics_i2c_rmi4.c | 1140 -------------------------
>  drivers/staging/ste_rmi4/synaptics_i2c_rmi4.h |   46 -
>  7 files changed, 1209 deletions(-)
>  delete mode 100644 drivers/staging/ste_rmi4/Kconfig
>  delete mode 100644 drivers/staging/ste_rmi4/Makefile
>  delete mode 100644 drivers/staging/ste_rmi4/TODO
>  delete mode 100644 drivers/staging/ste_rmi4/synaptics_i2c_rmi4.c
>  delete mode 100644 drivers/staging/ste_rmi4/synaptics_i2c_rmi4.h
>
> diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
> index 5d3b86a..e89c02c 100644
> --- a/drivers/staging/Kconfig
> +++ b/drivers/staging/Kconfig
> @@ -64,8 +64,6 @@ source "drivers/staging/emxx_udc/Kconfig"
>
>  source "drivers/staging/speakup/Kconfig"
>
> -source "drivers/staging/ste_rmi4/Kconfig"
> -
>  source "drivers/staging/nvec/Kconfig"
>
>  source "drivers/staging/media/Kconfig"
> diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
> index 30918ed..654ee8d 100644
> --- a/drivers/staging/Makefile
> +++ b/drivers/staging/Makefile
> @@ -26,7 +26,6 @@ obj-$(CONFIG_FB_SM750)                += sm750fb/
>  obj-$(CONFIG_FB_XGI)           += xgifb/
>  obj-$(CONFIG_USB_EMXX)         += emxx_udc/
>  obj-$(CONFIG_SPEAKUP)          += speakup/
> -obj-$(CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4)   += ste_rmi4/
>  obj-$(CONFIG_MFD_NVEC)         += nvec/
>  obj-$(CONFIG_STAGING_RDMA)     += rdma/
>  obj-$(CONFIG_ANDROID)          += android/
> diff --git a/drivers/staging/ste_rmi4/Kconfig b/drivers/staging/ste_rmi4/Kconfig
> deleted file mode 100644
> index e867950..0000000
> --- a/drivers/staging/ste_rmi4/Kconfig
> +++ /dev/null
> @@ -1,9 +0,0 @@
> -config TOUCHSCREEN_SYNAPTICS_I2C_RMI4
> -       tristate "Synaptics i2c rmi4 touchscreen"
> -       depends on I2C && INPUT
> -       help
> -         Say Y here if you have a Synaptics RMI4 and
> -         want to enable support for the built-in touchscreen.
> -
> -         To compile this driver as a module, choose M here: the
> -         module will be called synaptics_rmi4_ts.
> diff --git a/drivers/staging/ste_rmi4/Makefile b/drivers/staging/ste_rmi4/Makefile
> deleted file mode 100644
> index 6cce2ed..0000000
> --- a/drivers/staging/ste_rmi4/Makefile
> +++ /dev/null
> @@ -1,4 +0,0 @@
> -#
> -# Makefile for the RMI4 touchscreen driver.
> -#
> -obj-$(CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4) += synaptics_i2c_rmi4.o
> diff --git a/drivers/staging/ste_rmi4/TODO b/drivers/staging/ste_rmi4/TODO
> deleted file mode 100644
> index 9be2437..0000000
> --- a/drivers/staging/ste_rmi4/TODO
> +++ /dev/null
> @@ -1,7 +0,0 @@
> -TODO
> -----
> -
> -Wait for the official upstream synaptics rmi4 clearpad drivers as promised over the past few months
> -Merge any device support needed from this driver into it
> -Delete this driver
> -
> diff --git a/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.c b/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.c
> deleted file mode 100644
> index 824d460..0000000
> --- a/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.c
> +++ /dev/null
> @@ -1,1140 +0,0 @@
> -/**
> - *
> - * Synaptics Register Mapped Interface (RMI4) I2C Physical Layer Driver.
> - * Copyright (c) 2007-2010, Synaptics Incorporated
> - *
> - * Author: Js HA <js.ha@xxxxxxxxxxxxxx> for ST-Ericsson
> - * Author: Naveen Kumar G <naveen.gaddipati@xxxxxxxxxxxxxx> for ST-Ericsson
> - * Copyright 2010 (c) ST-Ericsson AB
> - */
> -/*
> - * This file is licensed under the GPL2 license.
> - *
> - *#############################################################################
> - * GPL
> - *
> - * This program is free software; you can redistribute it and/or modify it
> - * under the terms of the GNU General Public License version 2 as published
> - * by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful, but
> - * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
> - * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
> - * for more details.
> - *
> - *#############################################################################
> - */
> -
> -#include <linux/input.h>
> -#include <linux/slab.h>
> -#include <linux/i2c.h>
> -#include <linux/interrupt.h>
> -#include <linux/regulator/consumer.h>
> -#include <linux/module.h>
> -#include <linux/input/mt.h>
> -#include "synaptics_i2c_rmi4.h"
> -
> -/* TODO: for multiple device support will need a per-device mutex */
> -#define DRIVER_NAME "synaptics_rmi4_i2c"
> -
> -#define MAX_ERROR_REPORT       6
> -#define MAX_TOUCH_MAJOR                15
> -#define MAX_RETRY_COUNT                5
> -#define STD_QUERY_LEN          21
> -#define PAGE_LEN               2
> -#define DATA_BUF_LEN           32
> -#define BUF_LEN                        37
> -#define QUERY_LEN              9
> -#define DATA_LEN               12
> -#define HAS_TAP                        0x01
> -#define HAS_PALMDETECT         0x01
> -#define HAS_ROTATE             0x02
> -#define HAS_TAPANDHOLD         0x02
> -#define HAS_DOUBLETAP          0x04
> -#define HAS_EARLYTAP           0x08
> -#define HAS_RELEASE            0x08
> -#define HAS_FLICK              0x10
> -#define HAS_PRESS              0x20
> -#define HAS_PINCH              0x40
> -
> -#define MASK_16BIT             0xFFFF
> -#define MASK_8BIT              0xFF
> -#define MASK_7BIT              0x7F
> -#define MASK_5BIT              0x1F
> -#define MASK_4BIT              0x0F
> -#define MASK_3BIT              0x07
> -#define MASK_2BIT              0x03
> -#define TOUCHPAD_CTRL_INTR     0x8
> -#define PDT_START_SCAN_LOCATION (0x00E9)
> -#define PDT_END_SCAN_LOCATION  (0x000A)
> -#define PDT_ENTRY_SIZE         (0x0006)
> -#define SYNAPTICS_RMI4_TOUCHPAD_FUNC_NUM       (0x11)
> -#define SYNAPTICS_RMI4_DEVICE_CONTROL_FUNC_NUM (0x01)
> -
> -/**
> - * struct synaptics_rmi4_fn_desc - contains the function descriptor information
> - * @query_base_addr: base address for query
> - * @cmd_base_addr: base address for command
> - * @ctrl_base_addr: base address for control
> - * @data_base_addr: base address for data
> - * @intr_src_count: count for the interrupt source
> - * @fn_number: function number
> - *
> - * This structure is used to gives the function descriptor information
> - * of the particular functionality.
> - */
> -struct synaptics_rmi4_fn_desc {
> -       unsigned char   query_base_addr;
> -       unsigned char   cmd_base_addr;
> -       unsigned char   ctrl_base_addr;
> -       unsigned char   data_base_addr;
> -       unsigned char   intr_src_count;
> -       unsigned char   fn_number;
> -};
> -
> -/**
> - * struct synaptics_rmi4_fn - contains the function information
> - * @fn_number: function number
> - * @num_of_data_sources: number of data sources
> - * @num_of_data_points: number of fingers touched
> - * @size_of_data_register_block: data register block size
> - * @index_to_intr_reg: index for interrupt register
> - * @intr_mask: interrupt mask value
> - * @fn_desc: variable for function descriptor structure
> - * @link: linked list for function descriptors
> - *
> - * This structure gives information about the number of data sources and
> - * the number of data registers associated with the function.
> - */
> -struct synaptics_rmi4_fn {
> -       unsigned char           fn_number;
> -       unsigned char           num_of_data_sources;
> -       unsigned char           num_of_data_points;
> -       unsigned char           size_of_data_register_block;
> -       unsigned char           index_to_intr_reg;
> -       unsigned char           intr_mask;
> -       struct synaptics_rmi4_fn_desc   fn_desc;
> -       struct list_head        link;
> -};
> -
> -/**
> - * struct synaptics_rmi4_device_info - contains the rmi4 device information
> - * @version_major: protocol major version number
> - * @version_minor: protocol minor version number
> - * @manufacturer_id: manufacturer identification byte
> - * @product_props: product properties information
> - * @product_info: product info array
> - * @date_code: device manufacture date
> - * @tester_id: tester id array
> - * @serial_number: serial number for that device
> - * @product_id_string: product id for the device
> - * @support_fn_list: linked list for device information
> - *
> - * This structure gives information about the number of data sources and
> - * the number of data registers associated with the function.
> - */
> -struct synaptics_rmi4_device_info {
> -       unsigned int            version_major;
> -       unsigned int            version_minor;
> -       unsigned char           manufacturer_id;
> -       unsigned char           product_props;
> -       unsigned char           product_info[2];
> -       unsigned char           date_code[3];
> -       unsigned short          tester_id;
> -       unsigned short          serial_number;
> -       unsigned char           product_id_string[11];
> -       struct list_head        support_fn_list;
> -};
> -
> -/**
> - * struct synaptics_rmi4_data - contains the rmi4 device data
> - * @rmi4_mod_info: structure variable for rmi4 device info
> - * @input_dev: pointer for input device
> - * @i2c_client: pointer for i2c client
> - * @board: constant pointer for touch platform data
> - * @fn_list_mutex: mutex for function list
> - * @rmi4_page_mutex: mutex for rmi4 page
> - * @current_page: variable for integer
> - * @number_of_interrupt_register: interrupt registers count
> - * @fn01_ctrl_base_addr: control base address for fn01
> - * @fn01_query_base_addr: query base address for fn01
> - * @fn01_data_base_addr: data base address for fn01
> - * @sensor_max_x: sensor maximum x value
> - * @sensor_max_y: sensor maximum y value
> - * @regulator: pointer to the regulator structure
> - * @wait: wait queue structure variable
> - * @touch_stopped: flag to stop the thread function
> - * @fingers_supported: maximum supported fingers
> - *
> - * This structure gives the device data information.
> - */
> -struct synaptics_rmi4_data {
> -       struct synaptics_rmi4_device_info rmi4_mod_info;
> -       struct input_dev        *input_dev;
> -       struct i2c_client       *i2c_client;
> -       const struct synaptics_rmi4_platform_data *board;
> -       struct mutex            fn_list_mutex;
> -       struct mutex            rmi4_page_mutex;
> -       int                     current_page;
> -       unsigned int            number_of_interrupt_register;
> -       unsigned short          fn01_ctrl_base_addr;
> -       unsigned short          fn01_query_base_addr;
> -       unsigned short          fn01_data_base_addr;
> -       int                     sensor_max_x;
> -       int                     sensor_max_y;
> -       struct regulator        *regulator;
> -       wait_queue_head_t       wait;
> -       bool                    touch_stopped;
> -       unsigned char           fingers_supported;
> -};
> -
> -/**
> - * synaptics_rmi4_set_page() - sets the page
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @address: set the address of the page
> - *
> - * This function is used to set the page and returns integer.
> - */
> -static int synaptics_rmi4_set_page(struct synaptics_rmi4_data *pdata,
> -                                       unsigned int address)
> -{
> -       unsigned char   txbuf[PAGE_LEN];
> -       int             retval;
> -       unsigned int    page;
> -       struct i2c_client *i2c = pdata->i2c_client;
> -
> -       page    = ((address >> 8) & MASK_8BIT);
> -       if (page != pdata->current_page) {
> -               txbuf[0]        = MASK_8BIT;
> -               txbuf[1]        = page;
> -               retval  = i2c_master_send(i2c, txbuf, PAGE_LEN);
> -               if (retval != PAGE_LEN)
> -                       dev_err(&i2c->dev, "failed:%d\n", retval);
> -               else
> -                       pdata->current_page = page;
> -       } else
> -               retval = PAGE_LEN;
> -       return retval;
> -}
> -/**
> - * synaptics_rmi4_i2c_block_read() - read the block of data
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @address: read the block of data from this offset
> - * @valp: pointer to a buffer containing the data to be read
> - * @size: number of bytes to read
> - *
> - * This function is to read the block of data and returns integer.
> - */
> -static int synaptics_rmi4_i2c_block_read(struct synaptics_rmi4_data *pdata,
> -                                               unsigned short address,
> -                                               unsigned char *valp, int size)
> -{
> -       int retval = 0;
> -       int retry_count = 0;
> -       int index;
> -       struct i2c_client *i2c = pdata->i2c_client;
> -
> -       mutex_lock(&(pdata->rmi4_page_mutex));
> -       retval = synaptics_rmi4_set_page(pdata, address);
> -       if (retval != PAGE_LEN)
> -               goto exit;
> -       index = address & MASK_8BIT;
> -retry:
> -       retval = i2c_smbus_read_i2c_block_data(i2c, index, size, valp);
> -       if (retval != size) {
> -               if (++retry_count == MAX_RETRY_COUNT)
> -                       dev_err(&i2c->dev,
> -                               "%s:address 0x%04x size %d failed:%d\n",
> -                                       __func__, address, size, retval);
> -               else {
> -                       synaptics_rmi4_set_page(pdata, address);
> -                       goto retry;
> -               }
> -       }
> -exit:
> -       mutex_unlock(&(pdata->rmi4_page_mutex));
> -       return retval;
> -}
> -
> -/**
> - * synaptics_rmi4_i2c_byte_write() - write the single byte data
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @address: write the block of data from this offset
> - * @data: data to be write
> - *
> - * This function is to write the single byte data and returns integer.
> - */
> -static int synaptics_rmi4_i2c_byte_write(struct synaptics_rmi4_data *pdata,
> -                                               unsigned short address,
> -                                               unsigned char data)
> -{
> -       unsigned char txbuf[2];
> -       int retval = 0;
> -       struct i2c_client *i2c = pdata->i2c_client;
> -
> -       /* Can't have anyone else changing the page behind our backs */
> -       mutex_lock(&(pdata->rmi4_page_mutex));
> -
> -       retval = synaptics_rmi4_set_page(pdata, address);
> -       if (retval != PAGE_LEN)
> -               goto exit;
> -       txbuf[0]        = address & MASK_8BIT;
> -       txbuf[1]        = data;
> -       retval          = i2c_master_send(pdata->i2c_client, txbuf, 2);
> -       /* Add in retry on writes only in certain error return values */
> -       if (retval != 2) {
> -               dev_err(&i2c->dev, "failed:%d\n", retval);
> -               retval = -EIO;
> -       } else
> -               retval = 1;
> -exit:
> -       mutex_unlock(&(pdata->rmi4_page_mutex));
> -       return retval;
> -}
> -
> -/**
> - * synpatics_rmi4_touchpad_report() - reports for the rmi4 touchpad device
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @rfi: pointer to synaptics_rmi4_fn structure
> - *
> - * This function calls to reports for the rmi4 touchpad device
> - */
> -static int synpatics_rmi4_touchpad_report(struct synaptics_rmi4_data *pdata,
> -                                               struct synaptics_rmi4_fn *rfi)
> -{
> -       /* number of touch points - fingers down in this case */
> -       int     touch_count = 0;
> -       int     finger;
> -       int     finger_registers;
> -       int     reg;
> -       int     finger_shift;
> -       int     finger_status;
> -       int     retval;
> -       int     x, y;
> -       int     wx, wy;
> -       unsigned short  data_base_addr;
> -       unsigned short  data_offset;
> -       unsigned char   data_reg_blk_size;
> -       unsigned char   values[2];
> -       unsigned char   data[DATA_LEN];
> -       unsigned char   fingers_supported = pdata->fingers_supported;
> -       struct  i2c_client *client = pdata->i2c_client;
> -       struct  input_dev *input_dev = pdata->input_dev;
> -
> -       /* get 2D sensor finger data */
> -       /*
> -        * First get the finger status field - the size of the finger status
> -        * field is determined by the number of finger supporte - 2 bits per
> -        * finger, so the number of registers to read is:
> -        * registerCount = ceil(numberOfFingers/4).
> -        * Read the required number of registers and check each 2 bit field to
> -        * determine if a finger is down:
> -        *      00 = finger not present,
> -        *      01 = finger present and data accurate,
> -        *      10 = finger present but data may not be accurate,
> -        *      11 = reserved for product use.
> -        */
> -       finger_registers        = (fingers_supported + 3)/4;
> -       data_base_addr          = rfi->fn_desc.data_base_addr;
> -       retval = synaptics_rmi4_i2c_block_read(pdata, data_base_addr, values,
> -                                                       finger_registers);
> -       if (retval != finger_registers) {
> -               dev_err(&client->dev, "%s:read status registers failed\n",
> -                                                               __func__);
> -               return 0;
> -       }
> -       /*
> -        * For each finger present, read the proper number of registers
> -        * to get absolute data.
> -        */
> -       data_reg_blk_size = rfi->size_of_data_register_block;
> -       for (finger = 0; finger < fingers_supported; finger++) {
> -               /* determine which data byte the finger status is in */
> -               reg = finger/4;
> -               /* bit shift to get finger's status */
> -               finger_shift    = (finger % 4) * 2;
> -               finger_status   = (values[reg] >> finger_shift) & 3;
> -               /*
> -                * if finger status indicates a finger is present then
> -                * read the finger data and report it
> -                */
> -               input_mt_slot(input_dev, finger);
> -               input_mt_report_slot_state(input_dev, MT_TOOL_FINGER,
> -                                                       finger_status != 0);
> -
> -               if (finger_status) {
> -                       /* Read the finger data */
> -                       data_offset = data_base_addr +
> -                                       ((finger * data_reg_blk_size) +
> -                                       finger_registers);
> -                       retval = synaptics_rmi4_i2c_block_read(pdata,
> -                                               data_offset, data,
> -                                               data_reg_blk_size);
> -                       if (retval != data_reg_blk_size) {
> -                               dev_err(&client->dev, "%s:read data failed\n",
> -                                                               __func__);
> -                               return 0;
> -                       }
> -                       x = (data[0] << 4) | (data[2] & MASK_4BIT);
> -                       y = (data[1] << 4) | ((data[2] >> 4) & MASK_4BIT);
> -                       wy = (data[3] >> 4) & MASK_4BIT;
> -                       wx = (data[3] & MASK_4BIT);
> -
> -                       if (pdata->board->x_flip)
> -                               x = pdata->sensor_max_x - x;
> -                       if (pdata->board->y_flip)
> -                               y = pdata->sensor_max_y - y;
> -
> -                       input_report_abs(input_dev, ABS_MT_TOUCH_MAJOR,
> -                                                               max(wx, wy));
> -                       input_report_abs(input_dev, ABS_MT_POSITION_X, x);
> -                       input_report_abs(input_dev, ABS_MT_POSITION_Y, y);
> -
> -                       /* number of active touch points */
> -                       touch_count++;
> -               }
> -       }
> -
> -       /* sync after groups of events */
> -       input_mt_sync_frame(input_dev);
> -       input_sync(input_dev);
> -       /* return the number of touch points */
> -       return touch_count;
> -}
> -
> -/**
> - * synaptics_rmi4_report_device() - reports the rmi4 device
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @rfi: pointer to synaptics_rmi4_fn
> - *
> - * This function is used to call the report function of the rmi4 device.
> - */
> -static int synaptics_rmi4_report_device(struct synaptics_rmi4_data *pdata,
> -                                       struct synaptics_rmi4_fn *rfi)
> -{
> -       int touch = 0;
> -       struct  i2c_client *client = pdata->i2c_client;
> -       static int num_error_reports;
> -
> -       if (rfi->fn_number != SYNAPTICS_RMI4_TOUCHPAD_FUNC_NUM) {
> -               num_error_reports++;
> -               if (num_error_reports < MAX_ERROR_REPORT)
> -                       dev_err(&client->dev, "%s:report not supported\n",
> -                                                               __func__);
> -       } else
> -               touch = synpatics_rmi4_touchpad_report(pdata, rfi);
> -       return touch;
> -}
> -/**
> - * synaptics_rmi4_sensor_report() - reports to input subsystem
> - * @pdata: pointer to synaptics_rmi4_data structure
> - *
> - * This function is used to reads in all data sources and reports
> - * them to the input subsystem.
> - */
> -static int synaptics_rmi4_sensor_report(struct synaptics_rmi4_data *pdata)
> -{
> -       unsigned char   intr_status[4];
> -       /* number of touch points - fingers or buttons */
> -       int touch = 0;
> -       unsigned int retval;
> -       struct synaptics_rmi4_fn                *rfi;
> -       struct synaptics_rmi4_device_info       *rmi;
> -       struct  i2c_client *client = pdata->i2c_client;
> -
> -       /*
> -        * Get the interrupt status from the function $01
> -        * control register+1 to find which source(s) were interrupting
> -        * so we can read the data from the source(s) (2D sensor, buttons..)
> -        */
> -       retval = synaptics_rmi4_i2c_block_read(pdata,
> -                                       pdata->fn01_data_base_addr + 1,
> -                                       intr_status,
> -                                       pdata->number_of_interrupt_register);
> -       if (retval != pdata->number_of_interrupt_register) {
> -               dev_err(&client->dev,
> -                               "could not read interrupt status registers\n");
> -               return 0;
> -       }
> -       /*
> -        * check each function that has data sources and if the interrupt for
> -        * that triggered then call that RMI4 functions report() function to
> -        * gather data and report it to the input subsystem
> -        */
> -       rmi = &(pdata->rmi4_mod_info);
> -       list_for_each_entry(rfi, &rmi->support_fn_list, link) {
> -               if (rfi->num_of_data_sources) {
> -                       if (intr_status[rfi->index_to_intr_reg] &
> -                                                       rfi->intr_mask)
> -                               touch = synaptics_rmi4_report_device(pdata,
> -                                                                       rfi);
> -               }
> -       }
> -       /* return the number of touch points */
> -       return touch;
> -}
> -
> -/**
> - * synaptics_rmi4_irq() - thread function for rmi4 attention line
> - * @irq: irq value
> - * @data: void pointer
> - *
> - * This function is interrupt thread function. It just notifies the
> - * application layer that attention is required.
> - */
> -static irqreturn_t synaptics_rmi4_irq(int irq, void *data)
> -{
> -       struct synaptics_rmi4_data *pdata = data;
> -       int touch_count;
> -
> -       do {
> -               touch_count = synaptics_rmi4_sensor_report(pdata);
> -               if (touch_count)
> -                       wait_event_timeout(pdata->wait, pdata->touch_stopped,
> -                                                       msecs_to_jiffies(1));
> -               else
> -                       break;
> -       } while (!pdata->touch_stopped);
> -       return IRQ_HANDLED;
> -}
> -
> -/**
> - * synpatics_rmi4_touchpad_detect() - detects the rmi4 touchpad device
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @rfi: pointer to synaptics_rmi4_fn structure
> - * @fd: pointer to synaptics_rmi4_fn_desc structure
> - * @interruptcount: count the number of interrupts
> - *
> - * This function calls to detects the rmi4 touchpad device
> - */
> -static int synpatics_rmi4_touchpad_detect(struct synaptics_rmi4_data *pdata,
> -                                       struct synaptics_rmi4_fn *rfi,
> -                                       struct synaptics_rmi4_fn_desc *fd,
> -                                       unsigned int interruptcount)
> -{
> -       unsigned char   queries[QUERY_LEN];
> -       unsigned short  intr_offset;
> -       unsigned char   abs_data_size;
> -       unsigned char   abs_data_blk_size;
> -       unsigned char   egr_0, egr_1;
> -       unsigned int    all_data_blk_size;
> -       int     has_pinch, has_flick, has_tap;
> -       int     has_tapandhold, has_doubletap;
> -       int     has_earlytap, has_press;
> -       int     has_palmdetect, has_rotate;
> -       int     has_rel;
> -       int     i;
> -       int     retval;
> -       struct  i2c_client *client = pdata->i2c_client;
> -
> -       rfi->fn_desc.query_base_addr    = fd->query_base_addr;
> -       rfi->fn_desc.data_base_addr     = fd->data_base_addr;
> -       rfi->fn_desc.intr_src_count     = fd->intr_src_count;
> -       rfi->fn_desc.fn_number          = fd->fn_number;
> -       rfi->fn_number                  = fd->fn_number;
> -       rfi->num_of_data_sources        = fd->intr_src_count;
> -       rfi->fn_desc.ctrl_base_addr     = fd->ctrl_base_addr;
> -       rfi->fn_desc.cmd_base_addr      = fd->cmd_base_addr;
> -
> -       /*
> -        * need to get number of fingers supported, data size, etc.
> -        * to be used when getting data since the number of registers to
> -        * read depends on the number of fingers supported and data size.
> -        */
> -       retval = synaptics_rmi4_i2c_block_read(pdata, fd->query_base_addr,
> -                                                       queries,
> -                                                       sizeof(queries));
> -       if (retval != sizeof(queries)) {
> -               dev_err(&client->dev, "%s:read function query registers\n",
> -                                                       __func__);
> -               return retval;
> -       }
> -       /*
> -        * 2D data sources have only 3 bits for the number of fingers
> -        * supported - so the encoding is a bit weird.
> -        */
> -       if ((queries[1] & MASK_3BIT) <= 4)
> -               /* add 1 since zero based */
> -               rfi->num_of_data_points = (queries[1] & MASK_3BIT) + 1;
> -       else {
> -               /*
> -                * a value of 5 is up to 10 fingers - 6 and 7 are reserved
> -                * (shouldn't get these i int retval;n a normal 2D source).
> -                */
> -               if ((queries[1] & MASK_3BIT) == 5)
> -                       rfi->num_of_data_points = 10;
> -       }
> -       pdata->fingers_supported = rfi->num_of_data_points;
> -       /* Need to get interrupt info for handling interrupts */
> -       rfi->index_to_intr_reg = (interruptcount + 7)/8;
> -       if (rfi->index_to_intr_reg != 0)
> -               rfi->index_to_intr_reg -= 1;
> -       /*
> -        * loop through interrupts for each source in fn $11
> -        * and or in a bit to the interrupt mask for each.
> -        */
> -       intr_offset = interruptcount % 8;
> -       rfi->intr_mask = 0;
> -       for (i = intr_offset;
> -               i < ((fd->intr_src_count & MASK_3BIT) + intr_offset); i++)
> -               rfi->intr_mask |= 1 << i;
> -
> -       /* Size of just the absolute data for one finger */
> -       abs_data_size   = queries[5] & MASK_2BIT;
> -       /* One each for X and Y, one for LSB for X & Y, one for W, one for Z */
> -       abs_data_blk_size = 3 + (2 * (abs_data_size == 0 ? 1 : 0));
> -       rfi->size_of_data_register_block = abs_data_blk_size;
> -
> -       /*
> -        * need to determine the size of data to read - this depends on
> -        * conditions such as whether Relative data is reported and if Gesture
> -        * data is reported.
> -        */
> -       egr_0 = queries[7];
> -       egr_1 = queries[8];
> -
> -       /*
> -        * Get info about what EGR data is supported, whether it has
> -        * Relative data supported, etc.
> -        */
> -       has_pinch       = egr_0 & HAS_PINCH;
> -       has_flick       = egr_0 & HAS_FLICK;
> -       has_tap         = egr_0 & HAS_TAP;
> -       has_earlytap    = egr_0 & HAS_EARLYTAP;
> -       has_press       = egr_0 & HAS_PRESS;
> -       has_rotate      = egr_1 & HAS_ROTATE;
> -       has_rel         = queries[1] & HAS_RELEASE;
> -       has_tapandhold  = egr_0 & HAS_TAPANDHOLD;
> -       has_doubletap   = egr_0 & HAS_DOUBLETAP;
> -       has_palmdetect  = egr_1 & HAS_PALMDETECT;
> -
> -       /*
> -        * Size of all data including finger status, absolute data for each
> -        * finger, relative data and EGR data
> -        */
> -       all_data_blk_size =
> -               /* finger status, four fingers per register */
> -               ((rfi->num_of_data_points + 3) / 4) +
> -               /* absolute data, per finger times number of fingers */
> -               (abs_data_blk_size * rfi->num_of_data_points) +
> -               /*
> -                * two relative registers (if relative is being reported)
> -                */
> -               2 * has_rel +
> -               /*
> -                * F11_2D_data8 is only present if the egr_0
> -                * register is non-zero.
> -                */
> -               !!(egr_0) +
> -               /*
> -                * F11_2D_data9 is only present if either egr_0 or
> -                * egr_1 registers are non-zero.
> -                */
> -               (egr_0 || egr_1) +
> -               /*
> -                * F11_2D_data10 is only present if EGR_PINCH or EGR_FLICK of
> -                * egr_0 reports as 1.
> -                */
> -               !!(has_pinch | has_flick) +
> -               /*
> -                * F11_2D_data11 and F11_2D_data12 are only present if
> -                * EGR_FLICK of egr_0 reports as 1.
> -                */
> -               2 * !!(has_flick);
> -       return retval;
> -}
> -
> -/**
> - * synaptics_rmi4_touchpad_config() - configures the rmi4 touchpad device
> - * @pdata: pointer to synaptics_rmi4_data structure
> - * @rfi: pointer to synaptics_rmi4_fn structure
> - *
> - * This function calls to configures the rmi4 touchpad device
> - */
> -static int synaptics_rmi4_touchpad_config(struct synaptics_rmi4_data *pdata,
> -                                               struct synaptics_rmi4_fn *rfi)
> -{
> -       /*
> -        * For the data source - print info and do any
> -        * source specific configuration.
> -        */
> -       unsigned char data[BUF_LEN];
> -       int retval = 0;
> -       struct  i2c_client *client = pdata->i2c_client;
> -
> -       /* Get and print some info about the data source... */
> -       /* To Query 2D devices we need to read from the address obtained
> -        * from the function descriptor stored in the RMI function info.
> -        */
> -       retval = synaptics_rmi4_i2c_block_read(pdata,
> -                                               rfi->fn_desc.query_base_addr,
> -                                               data, QUERY_LEN);
> -       if (retval != QUERY_LEN)
> -               dev_err(&client->dev, "%s:read query registers failed\n",
> -                                                               __func__);
> -       else {
> -               retval = synaptics_rmi4_i2c_block_read(pdata,
> -                                               rfi->fn_desc.ctrl_base_addr,
> -                                               data, DATA_BUF_LEN);
> -               if (retval != DATA_BUF_LEN) {
> -                       dev_err(&client->dev,
> -                               "%s:read control registers failed\n",
> -                                                               __func__);
> -                       return retval;
> -               }
> -               /* Store these for use later*/
> -               pdata->sensor_max_x = ((data[6] & MASK_8BIT) << 0) |
> -                                               ((data[7] & MASK_4BIT) << 8);
> -               pdata->sensor_max_y = ((data[8] & MASK_5BIT) << 0) |
> -                                               ((data[9] & MASK_4BIT) << 8);
> -       }
> -       return retval;
> -}
> -
> -/**
> - * synaptics_rmi4_i2c_query_device() - query the rmi4 device
> - * @pdata: pointer to synaptics_rmi4_data structure
> - *
> - * This function is used to query the rmi4 device.
> - */
> -static int synaptics_rmi4_i2c_query_device(struct synaptics_rmi4_data *pdata)
> -{
> -       int i;
> -       int retval;
> -       unsigned char std_queries[STD_QUERY_LEN];
> -       unsigned char intr_count = 0;
> -       int data_sources = 0;
> -       unsigned int ctrl_offset;
> -       struct synaptics_rmi4_fn *rfi;
> -       struct synaptics_rmi4_fn_desc   rmi_fd;
> -       struct synaptics_rmi4_device_info *rmi;
> -       struct  i2c_client *client = pdata->i2c_client;
> -
> -       /*
> -        * init the physical drivers RMI module
> -        * info list of functions
> -        */
> -       INIT_LIST_HEAD(&pdata->rmi4_mod_info.support_fn_list);
> -
> -       /*
> -        * Read the Page Descriptor Table to determine what functions
> -        * are present
> -        */
> -       for (i = PDT_START_SCAN_LOCATION; i > PDT_END_SCAN_LOCATION;
> -                                               i -= PDT_ENTRY_SIZE) {
> -               retval = synaptics_rmi4_i2c_block_read(pdata, i,
> -                                               (unsigned char *)&rmi_fd,
> -                                               sizeof(rmi_fd));
> -               if (retval != sizeof(rmi_fd)) {
> -                       /* failed to read next PDT entry */
> -                       dev_err(&client->dev, "%s: read error\n", __func__);
> -                       return -EIO;
> -               }
> -               rfi = NULL;
> -               if (rmi_fd.fn_number) {
> -                       switch (rmi_fd.fn_number & MASK_8BIT) {
> -                       case SYNAPTICS_RMI4_DEVICE_CONTROL_FUNC_NUM:
> -                               pdata->fn01_query_base_addr =
> -                                               rmi_fd.query_base_addr;
> -                               pdata->fn01_ctrl_base_addr =
> -                                               rmi_fd.ctrl_base_addr;
> -                               pdata->fn01_data_base_addr =
> -                                               rmi_fd.data_base_addr;
> -                               break;
> -                       case SYNAPTICS_RMI4_TOUCHPAD_FUNC_NUM:
> -                               if (rmi_fd.intr_src_count) {
> -                                       rfi = kmalloc(sizeof(*rfi),
> -                                                     GFP_KERNEL);
> -                                       if (!rfi)
> -                                               return -ENOMEM;
> -                                       retval = synpatics_rmi4_touchpad_detect
> -                                                               (pdata, rfi,
> -                                                               &rmi_fd,
> -                                                               intr_count);
> -                                       if (retval < 0) {
> -                                               kfree(rfi);
> -                                               return retval;
> -                                       }
> -                               }
> -                               break;
> -                       }
> -                       /* interrupt count for next iteration */
> -                       intr_count += (rmi_fd.intr_src_count & MASK_3BIT);
> -                       /*
> -                        * We only want to add functions to the list
> -                        * that have data associated with them.
> -                        */
> -                       if (rfi && rmi_fd.intr_src_count) {
> -                               /* link this function info to the RMI module */
> -                               mutex_lock(&(pdata->fn_list_mutex));
> -                               list_add_tail(&rfi->link,
> -                                       &pdata->rmi4_mod_info.support_fn_list);
> -                               mutex_unlock(&(pdata->fn_list_mutex));
> -                       }
> -               } else {
> -                       /*
> -                        * A zero in the function number
> -                        * signals the end of the PDT
> -                        */
> -                       dev_dbg(&client->dev,
> -                               "%s:end of PDT\n", __func__);
> -                       break;
> -               }
> -       }
> -       /*
> -        * calculate the interrupt register count - used in the
> -        * ISR to read the correct number of interrupt registers
> -        */
> -       pdata->number_of_interrupt_register = (intr_count + 7) / 8;
> -       /*
> -        * Function $01 will be used to query the product properties,
> -        * and product ID  so we had to read the PDT above first to get
> -        * the Fn $01 query address and prior to filling in the product
> -        * info. NOTE: Even an unflashed device will still have FN $01.
> -        */
> -
> -       /* Load up the standard queries and get the RMI4 module info */
> -       retval = synaptics_rmi4_i2c_block_read(pdata,
> -                                       pdata->fn01_query_base_addr,
> -                                       std_queries,
> -                                       sizeof(std_queries));
> -       if (retval != sizeof(std_queries)) {
> -               dev_err(&client->dev, "%s:Failed reading queries\n",
> -                                                       __func__);
> -                return -EIO;
> -       }
> -
> -       /* Currently supported RMI version is 4.0 */
> -       pdata->rmi4_mod_info.version_major      = 4;
> -       pdata->rmi4_mod_info.version_minor      = 0;
> -       /*
> -        * get manufacturer id, product_props, product info,
> -        * date code, tester id, serial num and product id (name)
> -        */
> -       pdata->rmi4_mod_info.manufacturer_id    = std_queries[0];
> -       pdata->rmi4_mod_info.product_props      = std_queries[1];
> -       pdata->rmi4_mod_info.product_info[0]    = std_queries[2];
> -       pdata->rmi4_mod_info.product_info[1]    = std_queries[3];
> -       /* year - 2001-2032 */
> -       pdata->rmi4_mod_info.date_code[0]       = std_queries[4] & MASK_5BIT;
> -       /* month - 1-12 */
> -       pdata->rmi4_mod_info.date_code[1]       = std_queries[5] & MASK_4BIT;
> -       /* day - 1-31 */
> -       pdata->rmi4_mod_info.date_code[2]       = std_queries[6] & MASK_5BIT;
> -       pdata->rmi4_mod_info.tester_id = ((std_queries[7] & MASK_7BIT) << 8) |
> -                                               (std_queries[8] & MASK_7BIT);
> -       pdata->rmi4_mod_info.serial_number =
> -               ((std_queries[9] & MASK_7BIT) << 8) |
> -                               (std_queries[10] & MASK_7BIT);
> -       memcpy(pdata->rmi4_mod_info.product_id_string, &std_queries[11], 10);
> -
> -       /* Check if this is a Synaptics device - report if not. */
> -       if (pdata->rmi4_mod_info.manufacturer_id != 1)
> -               dev_err(&client->dev, "non-Synaptics mfg id:%d\n",
> -                       pdata->rmi4_mod_info.manufacturer_id);
> -
> -       list_for_each_entry(rfi, &pdata->rmi4_mod_info.support_fn_list, link)
> -               data_sources += rfi->num_of_data_sources;
> -       if (data_sources) {
> -               rmi = &(pdata->rmi4_mod_info);
> -               list_for_each_entry(rfi, &rmi->support_fn_list, link) {
> -                       if (rfi->num_of_data_sources) {
> -                               if (rfi->fn_number ==
> -                                       SYNAPTICS_RMI4_TOUCHPAD_FUNC_NUM) {
> -                                       retval = synaptics_rmi4_touchpad_config
> -                                                               (pdata, rfi);
> -                                       if (retval < 0)
> -                                               return retval;
> -                               } else
> -                                       dev_err(&client->dev,
> -                                               "%s:fn_number not supported\n",
> -                                                               __func__);
> -                               /*
> -                                * Turn on interrupts for this
> -                                * function's data sources.
> -                                */
> -                               ctrl_offset = pdata->fn01_ctrl_base_addr + 1 +
> -                                                       rfi->index_to_intr_reg;
> -                               retval = synaptics_rmi4_i2c_byte_write(pdata,
> -                                                       ctrl_offset,
> -                                                       rfi->intr_mask);
> -                               if (retval < 0)
> -                                       return retval;
> -                       }
> -               }
> -       }
> -       return 0;
> -}
> -
> -/*
> - * Descriptor structure.
> - * Describes the number of i2c devices on the bus that speak RMI.
> - */
> -static struct synaptics_rmi4_platform_data synaptics_rmi4_platformdata = {
> -       .irq_type       = (IRQF_TRIGGER_FALLING | IRQF_SHARED),
> -       .x_flip         = false,
> -       .y_flip         = true,
> -};
> -
> -/**
> - * synaptics_rmi4_probe() - Initialze the i2c-client touchscreen driver
> - * @i2c: i2c client structure pointer
> - * @id:i2c device id pointer
> - *
> - * This function will allocate and initialize the instance
> - * data and request the irq and set the instance data as the clients
> - * platform data then register the physical driver which will do a scan of
> - * the rmi4 Physical Device Table and enumerate any rmi4 functions that
> - * have data sources associated with them.
> - */
> -static int synaptics_rmi4_probe
> -       (struct i2c_client *client, const struct i2c_device_id *dev_id)
> -{
> -       int retval;
> -       unsigned char intr_status[4];
> -       struct synaptics_rmi4_data *rmi4_data;
> -       const struct synaptics_rmi4_platform_data *platformdata =
> -                                               client->dev.platform_data;
> -
> -       if (!i2c_check_functionality(client->adapter,
> -                                       I2C_FUNC_SMBUS_BYTE_DATA)) {
> -               dev_err(&client->dev, "i2c smbus byte data not supported\n");
> -               return -EIO;
> -       }
> -
> -       if (!platformdata)
> -               platformdata = &synaptics_rmi4_platformdata;
> -
> -       /* Allocate and initialize the instance data for this client */
> -       rmi4_data = kcalloc(2, sizeof(struct synaptics_rmi4_data),
> -                           GFP_KERNEL);
> -       if (!rmi4_data)
> -               return -ENOMEM;
> -
> -       rmi4_data->input_dev = input_allocate_device();
> -       if (rmi4_data->input_dev == NULL) {
> -               retval = -ENOMEM;
> -               goto err_input;
> -       }
> -
> -       rmi4_data->regulator = regulator_get(&client->dev, "vdd");
> -       if (IS_ERR(rmi4_data->regulator)) {
> -               dev_err(&client->dev, "%s:get regulator failed\n",
> -                                                       __func__);
> -               retval = PTR_ERR(rmi4_data->regulator);
> -               goto err_get_regulator;
> -       }
> -       retval = regulator_enable(rmi4_data->regulator);
> -       if (retval < 0) {
> -               dev_err(&client->dev, "%s:regulator enable failed\n",
> -                                                       __func__);
> -               goto err_regulator_enable;
> -       }
> -       init_waitqueue_head(&rmi4_data->wait);
> -       /*
> -        * Copy i2c_client pointer into RTID's i2c_client pointer for
> -        * later use in rmi4_read, rmi4_write, etc.
> -        */
> -       rmi4_data->i2c_client           = client;
> -       /* So we set the page correctly the first time */
> -       rmi4_data->current_page         = MASK_16BIT;
> -       rmi4_data->board                = platformdata;
> -       rmi4_data->touch_stopped        = false;
> -
> -       /* init the mutexes for maintain the lists */
> -       mutex_init(&(rmi4_data->fn_list_mutex));
> -       mutex_init(&(rmi4_data->rmi4_page_mutex));
> -
> -       /*
> -        * Register physical driver - this will call the detect function that
> -        * will then scan the device and determine the supported
> -        * rmi4 functions.
> -        */
> -       retval = synaptics_rmi4_i2c_query_device(rmi4_data);
> -       if (retval) {
> -               dev_err(&client->dev, "%s: rmi4 query device failed\n",
> -                                                       __func__);
> -               goto err_query_dev;
> -       }
> -
> -       /* Store the instance data in the i2c_client */
> -       i2c_set_clientdata(client, rmi4_data);
> -
> -       /*initialize the input device parameters */
> -       rmi4_data->input_dev->name      = DRIVER_NAME;
> -       rmi4_data->input_dev->phys      = "Synaptics_Clearpad";
> -       rmi4_data->input_dev->id.bustype = BUS_I2C;
> -       rmi4_data->input_dev->dev.parent = &client->dev;
> -       input_set_drvdata(rmi4_data->input_dev, rmi4_data);
> -
> -       /* Initialize the function handlers for rmi4 */
> -       set_bit(EV_SYN, rmi4_data->input_dev->evbit);
> -       set_bit(EV_KEY, rmi4_data->input_dev->evbit);
> -       set_bit(EV_ABS, rmi4_data->input_dev->evbit);
> -
> -       input_set_abs_params(rmi4_data->input_dev, ABS_MT_POSITION_X, 0,
> -                                       rmi4_data->sensor_max_x, 0, 0);
> -       input_set_abs_params(rmi4_data->input_dev, ABS_MT_POSITION_Y, 0,
> -                                       rmi4_data->sensor_max_y, 0, 0);
> -       input_set_abs_params(rmi4_data->input_dev, ABS_MT_TOUCH_MAJOR, 0,
> -                                               MAX_TOUCH_MAJOR, 0, 0);
> -       input_mt_init_slots(rmi4_data->input_dev,
> -                               rmi4_data->fingers_supported, 0);
> -
> -       /* Clear interrupts */
> -       synaptics_rmi4_i2c_block_read(rmi4_data,
> -                       rmi4_data->fn01_data_base_addr + 1, intr_status,
> -                               rmi4_data->number_of_interrupt_register);
> -       retval = request_threaded_irq(client->irq, NULL,
> -                                       synaptics_rmi4_irq,
> -                                       platformdata->irq_type,
> -                                       DRIVER_NAME, rmi4_data);
> -       if (retval) {
> -               dev_err(&client->dev, "Unable to get attn irq %d\n",
> -                       client->irq);
> -               goto err_query_dev;
> -       }
> -
> -       retval = input_register_device(rmi4_data->input_dev);
> -       if (retval) {
> -               dev_err(&client->dev, "%s:input register failed\n", __func__);
> -               goto err_free_irq;
> -       }
> -
> -       return retval;
> -
> -err_free_irq:
> -       free_irq(client->irq, rmi4_data);
> -err_query_dev:
> -       regulator_disable(rmi4_data->regulator);
> -err_regulator_enable:
> -       regulator_put(rmi4_data->regulator);
> -err_get_regulator:
> -       input_free_device(rmi4_data->input_dev);
> -       rmi4_data->input_dev = NULL;
> -err_input:
> -       kfree(rmi4_data);
> -
> -       return retval;
> -}
> -/**
> - * synaptics_rmi4_remove() - Removes the i2c-client touchscreen driver
> - * @client: i2c client structure pointer
> - *
> - * This function uses to remove the i2c-client
> - * touchscreen driver and returns integer.
> - */
> -static int synaptics_rmi4_remove(struct i2c_client *client)
> -{
> -       struct synaptics_rmi4_data *rmi4_data = i2c_get_clientdata(client);
> -
> -       rmi4_data->touch_stopped = true;
> -       wake_up(&rmi4_data->wait);
> -       free_irq(client->irq, rmi4_data);
> -       input_unregister_device(rmi4_data->input_dev);
> -       regulator_disable(rmi4_data->regulator);
> -       regulator_put(rmi4_data->regulator);
> -       kfree(rmi4_data);
> -
> -       return 0;
> -}
> -
> -#ifdef CONFIG_PM
> -/**
> - * synaptics_rmi4_suspend() - suspend the touch screen controller
> - * @dev: pointer to device structure
> - *
> - * This function is used to suspend the
> - * touch panel controller and returns integer
> - */
> -static int synaptics_rmi4_suspend(struct device *dev)
> -{
> -       /* Touch sleep mode */
> -       int retval;
> -       unsigned char intr_status;
> -       struct synaptics_rmi4_data *rmi4_data = dev_get_drvdata(dev);
> -
> -       rmi4_data->touch_stopped = true;
> -       disable_irq(rmi4_data->i2c_client->irq);
> -
> -       retval = synaptics_rmi4_i2c_block_read(rmi4_data,
> -                               rmi4_data->fn01_data_base_addr + 1,
> -                               &intr_status,
> -                               rmi4_data->number_of_interrupt_register);
> -       if (retval < 0)
> -               return retval;
> -
> -       retval = synaptics_rmi4_i2c_byte_write(rmi4_data,
> -                                       rmi4_data->fn01_ctrl_base_addr + 1,
> -                                       (intr_status & ~TOUCHPAD_CTRL_INTR));
> -       if (retval < 0)
> -               return retval;
> -
> -       regulator_disable(rmi4_data->regulator);
> -
> -       return 0;
> -}
> -/**
> - * synaptics_rmi4_resume() - resume the touch screen controller
> - * @dev: pointer to device structure
> - *
> - * This function is used to resume the touch panel
> - * controller and returns integer.
> - */
> -static int synaptics_rmi4_resume(struct device *dev)
> -{
> -       int retval;
> -       unsigned char intr_status;
> -       struct synaptics_rmi4_data *rmi4_data = dev_get_drvdata(dev);
> -
> -       retval = regulator_enable(rmi4_data->regulator);
> -       if (retval) {
> -               dev_err(dev, "Regulator enable failed (%d)\n", retval);
> -               return retval;
> -       }
> -
> -       enable_irq(rmi4_data->i2c_client->irq);
> -       rmi4_data->touch_stopped = false;
> -
> -       retval = synaptics_rmi4_i2c_block_read(rmi4_data,
> -                               rmi4_data->fn01_data_base_addr + 1,
> -                               &intr_status,
> -                               rmi4_data->number_of_interrupt_register);
> -       if (retval < 0)
> -               return retval;
> -
> -       retval = synaptics_rmi4_i2c_byte_write(rmi4_data,
> -                                       rmi4_data->fn01_ctrl_base_addr + 1,
> -                                       (intr_status | TOUCHPAD_CTRL_INTR));
> -       if (retval < 0)
> -               return retval;
> -
> -       return 0;
> -}
> -
> -#endif
> -
> -static SIMPLE_DEV_PM_OPS(synaptics_rmi4_dev_pm_ops, synaptics_rmi4_suspend,
> -                        synaptics_rmi4_resume);
> -
> -static const struct i2c_device_id synaptics_rmi4_id_table[] = {
> -       { DRIVER_NAME, 0 },
> -       { },
> -};
> -MODULE_DEVICE_TABLE(i2c, synaptics_rmi4_id_table);
> -
> -static struct i2c_driver synaptics_rmi4_driver = {
> -       .driver = {
> -               .name   =       DRIVER_NAME,
> -               .pm     =       &synaptics_rmi4_dev_pm_ops,
> -       },
> -       .probe          =       synaptics_rmi4_probe,
> -       .remove         =       synaptics_rmi4_remove,
> -       .id_table       =       synaptics_rmi4_id_table,
> -};
> -
> -module_i2c_driver(synaptics_rmi4_driver);
> -
> -MODULE_LICENSE("GPL v2");
> -MODULE_AUTHOR("naveen.gaddipati@xxxxxxxxxxxxxx, js.ha@xxxxxxxxxxxxxx");
> -MODULE_DESCRIPTION("synaptics rmi4 i2c touch Driver");
> diff --git a/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.h b/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.h
> deleted file mode 100644
> index 8c9166b..0000000
> --- a/drivers/staging/ste_rmi4/synaptics_i2c_rmi4.h
> +++ /dev/null
> @@ -1,46 +0,0 @@
> -/**
> - *
> - * Synaptics Register Mapped Interface (RMI4) I2C Physical Layer Driver.
> - * Copyright (c) 2007-2010, Synaptics Incorporated
> - *
> - * Author: Js HA <js.ha@xxxxxxxxxxxxxx> for ST-Ericsson
> - * Author: Naveen Kumar G <naveen.gaddipati@xxxxxxxxxxxxxx> for ST-Ericsson
> - * Copyright 2010 (c) ST-Ericsson AB
> - */
> -/*
> - * This file is licensed under the GPL2 license.
> - *
> - *#############################################################################
> - * GPL
> - *
> - * This program is free software; you can redistribute it and/or modify it
> - * under the terms of the GNU General Public License version 2 as published
> - * by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful, but
> - * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
> - * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
> - * for more details.
> - *
> - *#############################################################################
> - */
> -
> -#ifndef _SYNAPTICS_RMI4_H_INCLUDED_
> -#define _SYNAPTICS_RMI4_H_INCLUDED_
> -
> -/**
> - * struct synaptics_rmi4_platform_data - contains the rmi4 platform data
> - * @irq_number: irq number
> - * @irq_type: irq type
> - * @x flip: x flip flag
> - * @y flip: y flip flag
> - *
> - * This structure gives platform data for rmi4.
> - */
> -struct synaptics_rmi4_platform_data {
> -       int irq_type;
> -       bool x_flip;
> -       bool y_flip;
> -};
> -
> -#endif
> --
> 2.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-input" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux