On Wed, Nov 25, 2015 at 04:07:21PM -0800, Andrew Duggan wrote: > Add devicetree binding for I2C devices and add bindings for optional > parameters in the function drivers. Parameters for function drivers are > defined in child nodes for each of the functions. > > Signed-off-by: Andrew Duggan <aduggan@xxxxxxxxxxxxx> > --- > .../devicetree/bindings/input/rmi4/rmi_f01.txt | 39 ++++++++++++ > .../devicetree/bindings/input/rmi4/rmi_i2c.txt | 53 ++++++++++++++++ > .../devicetree/bindings/vendor-prefixes.txt | 1 + > drivers/input/rmi4/rmi_bus.c | 71 ++++++++++++++++++++++ > drivers/input/rmi4/rmi_driver.c | 28 +++++++++ > drivers/input/rmi4/rmi_i2c.c | 12 +++- > 6 files changed, 203 insertions(+), 1 deletion(-) > create mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt > create mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt > > diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt > new file mode 100644 > index 0000000..df34dd5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt > @@ -0,0 +1,39 @@ > +Synaptics RMI4 F01 Device Binding > + > +The Synaptics RMI4 core is able to support RMI4 devices using differnet > +transports and differnet functions. This file describes the device tree s/differnet/different/ > +bindings for devices which contain Function 1. Complete documentation > +for transports and other functions can be found in: > +Documentation/devicetree/bindings/input/rmi4. > + > +Additional documentation for F01 can be found at: > +http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf > + > +Optional Properties: > +- syna,nosleep-mode: If set the device will run at full power without sleeping. > + nosleep has 3 modes, 0 will not change the default > + setting, 1 will disable nosleep (allow sleeping), > + and 2 will enable nosleep (disabling sleep). > +- syna,wakeup-threshold: Defines the amplitude of the disturbance to the > + background capacitance that will cause the > + device to wake from dozing. > +- syna,doze-holdoff: The delay to wait after the last finger lift and the > + first doze cycle (in 0.1 second units). > +- syna,doze-interval: The time period that the device sleeps between finger > + activity (in 10 ms units). Use millisec units and -msec suffix. > + > + > +Example of a RMI4 I2C device with F01: > + Example: > + &i2c1 { > + rmi-i2c-dev@2c { > + compatible = "syna,rmi-i2c"; > + > + ... > + > + rmi-f01@1 { > + reg = <0x1>; > + syna,nosleep-mode = <1>; > + }; > + }; > + }; > diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt > new file mode 100644 > index 0000000..0f4a8e1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt > @@ -0,0 +1,53 @@ > +Synaptics RMI4 I2C Device Binding > + > +The Synaptics RMI4 core is able to support RMI4 devices using differnet > +transports and differnet functions. This file describes the device tree s/differnet/different/ > +bindings for devices using the I2C tranport driver. Complete documentation > +for other transports and functions cen be found ini > +Documentation/devicetree/bindings/input/rmi4. > + > +Required Properties: > +- compatible: syna,rmi-i2c This is not very specific. Perhaps at least "rmi4" instead of just rmi. > +- reg: I2C address > +- #address-cells: Set to 1 to indicate that the function child nodes > + consist of only on uint32 value. > +- #size-cells: Set to 0 to indicate that the function child nodes do not > + have a size property. > + > +Optional Properties: > +- interrupts: interrupt which the rmi device is connected to. > +- interrupt-parent: The interrupt controller. > +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt > + > +- syna,reset-delay-ms: The number of milliseconds to wait after resetting the "-msec" is the more commonly used abreviation in bindings. > + device. > + > +Function Parameters: > +Parameters specific to RMI functions are contained in child nodes of the rmi device > + node. Documentation for the parameters of each function can be found in: > +Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. > + > + > + > +Example: > + &i2c1 { > + rmi-i2c-dev@2c { > + compatible = "syna,rmi-i2c"; > + reg = <0x2c>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupt-parent = <&gpio>; > + interrupts = <4 2>; > + > + rmi-f01@1 { > + reg = <0x1>; > + syna,nosleep-mode = <1>; > + }; > + > + rmi-f11@11 { > + reg = <0x11>; > + syna,flip-y; > + syna,sensor-type = <2>; > + }; > + }; > + }; -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
