Adds support for the i2c based tsc2004. Support was added to the tsc2005 driver
due to the similarity of the devices.
Signed-off-by: Michael Welling <mwelling@xxxxxxxx>
---
v2: Fixes Kconfig based on report for 0-day build bot.
.../bindings/input/touchscreen/tsc2004.txt | 38 ++++
drivers/input/touchscreen/Kconfig | 7 +-
drivers/input/touchscreen/tsc2005.c | 206 ++++++++++++++++-----
3 files changed, 205 insertions(+), 46 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
new file mode 100644
index 0000000..14a37fb
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
@@ -0,0 +1,38 @@
+* Texas Instruments tsc2004 touchscreen controller
+
+Required properties:
+ - compatible : "ti,tsc2004"
+ - interrupts : IRQ specifier
+ - vio-supply : Regulator specifier
+
+Optional properties:
+ - reset-gpios : GPIO specifier
+ - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
+ in ohm (defaults to 280)
+ - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after
+ the configured time (in milli seconds), the driver
+ will reset it. This is disabled by default.
+ - properties defined in touchscreen.txt
+
+Example:
+
+&i2c3 {
+ tsc2004@48 {
+ compatible = "ti,tsc2004";
+ reg = <0x48>;
+ vio-supply = <&vio>;
+
+ reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+ interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>;
+
+ touchscreen-fuzz-x = <4>;
+ touchscreen-fuzz-y = <7>;
+ touchscreen-fuzz-pressure = <2>;
+ touchscreen-size-x = <4096>;
+ touchscreen-size-y = <4096>;
+ touchscreen-max-pressure = <2048>;
+
+ ti,x-plate-ohms = <280>;
+ ti,esd-recovery-timeout-ms = <8000>;
+ };
+}
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 80cc698..7355579 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -940,9 +940,10 @@ config TOUCHSCREEN_TSC_SERIO
module will be called tsc40.
config TOUCHSCREEN_TSC2005
- tristate "TSC2005 based touchscreens"
- depends on SPI_MASTER
- select REGMAP_SPI
+ tristate "TSC2004/TSC2005 based touchscreens"
+ depends on SPI_MASTER || I2C
+ select REGMAP_SPI if SPI_MASTER
+ select REGMAP_I2C if I2C
help
Say Y here if you have a TSC2005 based touchscreen.
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
index 0f65d02..08decd4 100644
--- a/drivers/input/touchscreen/tsc2005.c
+++ b/drivers/input/touchscreen/tsc2005.c
@@ -30,6 +30,7 @@
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/of.h>
+#include <linux/i2c.h>
#include <linux/spi/spi.h>
#include <linux/spi/tsc2005.h>
#include <linux/regulator/consumer.h>
@@ -151,6 +152,8 @@ struct tsc2005_data {
struct tsc2005 {
struct spi_device *spi;
+ struct i2c_client *i2c;
+ struct device *dev;
struct regmap *regmap;
struct input_dev *idev;
@@ -182,9 +185,11 @@ struct tsc2005 {
struct gpio_desc *reset_gpio;
void (*set_reset)(bool enable);
+
+ int irq;
};
-static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
+static int tsc2005_cmd_spi(struct tsc2005 *ts, u8 cmd)
{
u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
struct spi_transfer xfer = {
@@ -200,7 +205,7 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
error = spi_sync(ts->spi, &msg);
if (error) {
- dev_err(&ts->spi->dev, "%s: failed, command: %x, error: %d\n",
+ dev_err(ts->dev, "%s: failed, command: %x, spi error: %d\n",
__func__, cmd, error);
return error;
}
@@ -208,6 +213,32 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
return 0;
}
+static int tsc2005_cmd_i2c(struct tsc2005 *ts, u8 cmd)
+{
+ u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
+ s32 data;
+
+ data = i2c_smbus_write_byte(ts->i2c, tx);
+ if (data < 0) {
+ dev_err(&ts->dev, "%s: failed, command: %x i2c error: %d\n",
+ __func__, cmd, data);
+ return data;
+ }
+
+ return 0;
+}
+
+static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
+{
+ if (ts->spi)
+ return tsc2005_cmd_spi(ts, cmd);
+
+ if (ts->i2c)
+ return tsc2005_cmd_i2c(ts, cmd);
+
+ return -ENODEV;
+}
+
static void tsc2005_update_pen_state(struct tsc2005 *ts,
int x, int y, int pressure)
{
@@ -227,7 +258,7 @@ static void tsc2005_update_pen_state(struct tsc2005 *ts,
}
}
input_sync(ts->idev);
- dev_dbg(&ts->spi->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
+ dev_dbg(ts->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
pressure);
}
@@ -329,12 +360,12 @@ static void __tsc2005_disable(struct tsc2005 *ts)
{
tsc2005_stop_scan(ts);
- disable_irq(ts->spi->irq);
+ disable_irq(ts->irq);
del_timer_sync(&ts->penup_timer);
cancel_delayed_work_sync(&ts->esd_work);
- enable_irq(ts->spi->irq);
+ enable_irq(ts->irq);
}
/* must be called with ts->mutex held */
@@ -487,9 +518,9 @@ static void tsc2005_esd_work(struct work_struct *work)
* then we should reset the controller as if from power-up and start
* scanning again.
*/
- dev_info(&ts->spi->dev, "TSC2005 not responding - resetting\n");
+ dev_info(ts->dev, "TSC2005 not responding - resetting\n");
- disable_irq(ts->spi->irq);
+ disable_irq(ts->irq);
del_timer_sync(&ts->penup_timer);
tsc2005_update_pen_state(ts, 0, 0, 0);
@@ -498,7 +529,7 @@ static void tsc2005_esd_work(struct work_struct *work)
usleep_range(100, 500); /* only 10us required */
tsc2005_set_reset(ts, true);
- enable_irq(ts->spi->irq);
+ enable_irq(ts->irq);
tsc2005_start_scan(ts);
out:
@@ -540,10 +571,10 @@ static void tsc2005_close(struct input_dev *input)
mutex_unlock(&ts->mutex);
}
-static int tsc2005_probe(struct spi_device *spi)
+static int tsc200x_probe_common(struct device *dev, int irq, __u16 bustype)
{
- const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev);
- struct device_node *np = spi->dev.of_node;
+ const struct tsc2005_platform_data *pdata = dev_get_platdata(dev);
+ struct device_node *np = dev->of_node;
struct tsc2005 *ts;
struct input_dev *input_dev;
@@ -558,12 +589,12 @@ static int tsc2005_probe(struct spi_device *spi)
int error;
if (!np && !pdata) {
- dev_err(&spi->dev, "no platform data\n");
+ dev_err(dev, "no platform data\n");
return -ENODEV;
}
- if (spi->irq <= 0) {
- dev_err(&spi->dev, "no irq\n");
+ if (irq <= 0) {
+ dev_err(dev, "no irq\n");
return -ENODEV;
}
@@ -584,45 +615,46 @@ static int tsc2005_probe(struct spi_device *spi)
&esd_timeout);
}
- spi->mode = SPI_MODE_0;
- spi->bits_per_word = 8;
- if (!spi->max_speed_hz)
- spi->max_speed_hz = TSC2005_SPI_MAX_SPEED_HZ;
-
- error = spi_setup(spi);
- if (error)
- return error;
-
- ts = devm_kzalloc(&spi->dev, sizeof(*ts), GFP_KERNEL);
+ ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
if (!ts)
return -ENOMEM;
- input_dev = devm_input_allocate_device(&spi->dev);
+ input_dev = devm_input_allocate_device(dev);
if (!input_dev)
return -ENOMEM;
- ts->spi = spi;
+ ts->irq = irq;
+ ts->dev = dev;
ts->idev = input_dev;
- ts->regmap = devm_regmap_init_spi(spi, &tsc2005_regmap_config);
+ if (bustype == BUS_SPI) {
+ ts->spi = to_spi_device(dev);
+ ts->regmap = devm_regmap_init_spi(ts->spi,
+ &tsc2005_regmap_config);
+ } else if (bustype == BUS_I2C) {
+ ts->i2c = to_i2c_client(dev);
+ ts->regmap = devm_regmap_init_i2c(ts->i2c,
+ &tsc2005_regmap_config);
+ }
+
if (IS_ERR(ts->regmap))
return PTR_ERR(ts->regmap);
ts->x_plate_ohm = x_plate_ohm;
ts->esd_timeout = esd_timeout;
- ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
+ ts->reset_gpio = devm_gpiod_get_optional(dev, "reset",
GPIOD_OUT_HIGH);
if (IS_ERR(ts->reset_gpio)) {
error = PTR_ERR(ts->reset_gpio);
- dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error);
+ dev_err(dev, "error acquiring reset gpio: %d\n", error);
return error;
}
- ts->vio = devm_regulator_get_optional(&spi->dev, "vio");
+ ts->vio = devm_regulator_get_optional(dev, "vio");
if (IS_ERR(ts->vio)) {
error = PTR_ERR(ts->vio);
- dev_err(&spi->dev, "vio regulator missing (%d)", error);
+ dev_err(dev, "vio regulator missing (%d)", error);
return error;
}
@@ -637,12 +669,12 @@ static int tsc2005_probe(struct spi_device *spi)
INIT_DELAYED_WORK(&ts->esd_work, tsc2005_esd_work);
snprintf(ts->phys, sizeof(ts->phys),
- "%s/input-ts", dev_name(&spi->dev));
+ "%s/input-ts", dev_name(dev));
input_dev->name = "TSC2005 touchscreen";
input_dev->phys = ts->phys;
- input_dev->id.bustype = BUS_SPI;
- input_dev->dev.parent = &spi->dev;
+ input_dev->id.bustype = bustype;
+ input_dev->dev.parent = dev;
input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
@@ -661,12 +693,12 @@ static int tsc2005_probe(struct spi_device *spi)
/* Ensure the touchscreen is off */
tsc2005_stop_scan(ts);
- error = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
+ error = devm_request_threaded_irq(dev, irq, NULL,
tsc2005_irq_thread,
IRQF_TRIGGER_RISING | IRQF_ONESHOT,
"tsc2005", ts);
if (error) {
- dev_err(&spi->dev, "Failed to request irq, err: %d\n", error);
+ dev_err(dev, "Failed to request irq, err: %d\n", error);
return error;
}
@@ -677,32 +709,49 @@ static int tsc2005_probe(struct spi_device *spi)
return error;
}
- dev_set_drvdata(&spi->dev, ts);
- error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group);
+ dev_set_drvdata(dev, ts);
+ error = sysfs_create_group(&dev->kobj, &tsc2005_attr_group);
if (error) {
- dev_err(&spi->dev,
+ dev_err(dev,
"Failed to create sysfs attributes, err: %d\n", error);
goto disable_regulator;
}
error = input_register_device(ts->idev);
if (error) {
- dev_err(&spi->dev,
+ dev_err(dev,
"Failed to register input device, err: %d\n", error);
goto err_remove_sysfs;
}
- irq_set_irq_wake(spi->irq, 1);
+ irq_set_irq_wake(irq, 1);
return 0;
err_remove_sysfs:
- sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
+ sysfs_remove_group(&dev->kobj, &tsc2005_attr_group);
disable_regulator:
if (ts->vio)
regulator_disable(ts->vio);
return error;
}
+
+static int tsc2005_probe(struct spi_device *spi)
+{
+ int error;
+
+ spi->mode = SPI_MODE_0;
+ spi->bits_per_word = 8;
+ if (!spi->max_speed_hz)
+ spi->max_speed_hz = TSC2005_SPI_MAX_SPEED_HZ;
+
+ error = spi_setup(spi);
+ if (error)
+ return error;
+
+ return tsc200x_probe_common(&spi->dev, spi->irq, BUS_SPI);
+}
+
static int tsc2005_remove(struct spi_device *spi)
{
struct tsc2005 *ts = dev_get_drvdata(&spi->dev);
@@ -759,7 +808,78 @@ static struct spi_driver tsc2005_driver = {
.remove = tsc2005_remove,
};
-module_spi_driver(tsc2005_driver);
+static int tsc2004_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+
+{
+ return tsc200x_probe_common(&i2c->dev, i2c->irq, BUS_I2C);
+}
+
+static int tsc2004_remove(struct i2c_client *i2c)
+{
+ struct tsc2005 *ts = dev_get_drvdata(&i2c->dev);
+
+ sysfs_remove_group(&i2c->dev.kobj, &tsc2005_attr_group);
+
+ if (ts->vio)
+ regulator_disable(ts->vio);
+
+ return 0;
+}
+
+static const struct i2c_device_id tsc2004_idtable[] = {
+ { "tsc2004", 0 },
+ { }
+};
+
+MODULE_DEVICE_TABLE(i2c, tsc2004_idtable);
+
+#ifdef CONFIG_OF
+static const struct of_device_id tsc2004_of_match[] = {
+ { .compatible = "ti,tsc2004" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tsc2004_of_match);
+#endif
+
+static struct i2c_driver tsc2004_driver = {
+ .driver = {
+ .name = "tsc2004",
+ .of_match_table = of_match_ptr(tsc2004_of_match),
+ .pm = &tsc2005_pm_ops,
+ },
+ .id_table = tsc2004_idtable,
+ .probe = tsc2004_probe,
+ .remove = tsc2004_remove,
+};
+
+static int __init tsc2005_modinit(void)
+{
+ int ret = 0;
+#if IS_ENABLED(CONFIG_I2C)
+ ret = i2c_add_driver(&tsc2004_driver);
+ if (ret != 0)
+ pr_err("Failed to register tsc2004 I2C driver: %d\n", ret);
+#endif
+#if defined(CONFIG_SPI_MASTER)
+ ret = spi_register_driver(&tsc2005_driver);
+ if (ret != 0)
+ pr_err("Failed to register tsc2005 SPI driver: %d\n", ret);
+#endif
+ return ret;
+}
+module_init(tsc2005_modinit);
+
+static void __exit tsc2005_exit(void)
+{
+#if IS_ENABLED(CONFIG_I2C)
+ i2c_del_driver(&tsc2004_driver);
+#endif
+#if defined(CONFIG_SPI_MASTER)
+ spi_unregister_driver(&tsc2005_driver);
+#endif
+}
+module_exit(tsc2005_exit);
MODULE_AUTHOR("Lauri Leukkunen <lauri.leukkunen@xxxxxxxxx>");
MODULE_DESCRIPTION("TSC2005 Touchscreen Driver");
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
