On Tue, Oct 27, 2015 at 03:36:43PM -0500, Michael Welling wrote:
> Adds support for the i2c based tsc2004. Support was added to the tsc2005 driver
> due to the similarity of the devices.
>
It should be noted that the new TSC2004 I2C support was tested but I do not have
a device with the TSC2005 to verify.
Anyone with a N900 or other device with the TSC2005 willing to test this out and
see if I unintentionally broke the driver?
> Signed-off-by: Michael Welling <mwelling@xxxxxxxx>
> ---
> .../bindings/input/touchscreen/tsc2004.txt | 38 ++++
> drivers/input/touchscreen/Kconfig | 5 +-
> drivers/input/touchscreen/tsc2005.c | 206 ++++++++++++++++-----
> 3 files changed, 204 insertions(+), 45 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
> new file mode 100644
> index 0000000..14a37fb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2004.txt
> @@ -0,0 +1,38 @@
> +* Texas Instruments tsc2004 touchscreen controller
> +
> +Required properties:
> + - compatible : "ti,tsc2004"
> + - interrupts : IRQ specifier
> + - vio-supply : Regulator specifier
> +
> +Optional properties:
> + - reset-gpios : GPIO specifier
> + - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
> + in ohm (defaults to 280)
> + - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after
> + the configured time (in milli seconds), the driver
> + will reset it. This is disabled by default.
> + - properties defined in touchscreen.txt
> +
> +Example:
> +
> +&i2c3 {
> + tsc2004@48 {
> + compatible = "ti,tsc2004";
> + reg = <0x48>;
> + vio-supply = <&vio>;
> +
> + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>;
> +
> + touchscreen-fuzz-x = <4>;
> + touchscreen-fuzz-y = <7>;
> + touchscreen-fuzz-pressure = <2>;
> + touchscreen-size-x = <4096>;
> + touchscreen-size-y = <4096>;
> + touchscreen-max-pressure = <2048>;
> +
> + ti,x-plate-ohms = <280>;
> + ti,esd-recovery-timeout-ms = <8000>;
> + };
> +}
> diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> index 80cc698..7f311d7 100644
> --- a/drivers/input/touchscreen/Kconfig
> +++ b/drivers/input/touchscreen/Kconfig
> @@ -940,9 +940,10 @@ config TOUCHSCREEN_TSC_SERIO
> module will be called tsc40.
>
> config TOUCHSCREEN_TSC2005
> - tristate "TSC2005 based touchscreens"
> - depends on SPI_MASTER
> + tristate "TSC2004/TSC2005 based touchscreens"
> + depends on SPI_MASTER || I2C
> select REGMAP_SPI
> + select REGMAP_I2C
> help
> Say Y here if you have a TSC2005 based touchscreen.
>
> diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
> index 0f65d02..08decd4 100644
> --- a/drivers/input/touchscreen/tsc2005.c
> +++ b/drivers/input/touchscreen/tsc2005.c
> @@ -30,6 +30,7 @@
> #include <linux/delay.h>
> #include <linux/pm.h>
> #include <linux/of.h>
> +#include <linux/i2c.h>
> #include <linux/spi/spi.h>
> #include <linux/spi/tsc2005.h>
> #include <linux/regulator/consumer.h>
> @@ -151,6 +152,8 @@ struct tsc2005_data {
>
> struct tsc2005 {
> struct spi_device *spi;
> + struct i2c_client *i2c;
> + struct device *dev;
> struct regmap *regmap;
>
> struct input_dev *idev;
> @@ -182,9 +185,11 @@ struct tsc2005 {
>
> struct gpio_desc *reset_gpio;
> void (*set_reset)(bool enable);
> +
> + int irq;
> };
>
> -static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
> +static int tsc2005_cmd_spi(struct tsc2005 *ts, u8 cmd)
> {
> u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
> struct spi_transfer xfer = {
> @@ -200,7 +205,7 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
>
> error = spi_sync(ts->spi, &msg);
> if (error) {
> - dev_err(&ts->spi->dev, "%s: failed, command: %x, error: %d\n",
> + dev_err(ts->dev, "%s: failed, command: %x, spi error: %d\n",
> __func__, cmd, error);
> return error;
> }
> @@ -208,6 +213,32 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
> return 0;
> }
>
> +static int tsc2005_cmd_i2c(struct tsc2005 *ts, u8 cmd)
> +{
> + u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
> + s32 data;
> +
> + data = i2c_smbus_write_byte(ts->i2c, tx);
> + if (data < 0) {
> + dev_err(&ts->dev, "%s: failed, command: %x i2c error: %d\n",
> + __func__, cmd, data);
> + return data;
> + }
> +
> + return 0;
> +}
> +
> +static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
> +{
> + if (ts->spi)
> + return tsc2005_cmd_spi(ts, cmd);
> +
> + if (ts->i2c)
> + return tsc2005_cmd_i2c(ts, cmd);
> +
> + return -ENODEV;
> +}
> +
> static void tsc2005_update_pen_state(struct tsc2005 *ts,
> int x, int y, int pressure)
> {
> @@ -227,7 +258,7 @@ static void tsc2005_update_pen_state(struct tsc2005 *ts,
> }
> }
> input_sync(ts->idev);
> - dev_dbg(&ts->spi->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
> + dev_dbg(ts->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
> pressure);
> }
>
> @@ -329,12 +360,12 @@ static void __tsc2005_disable(struct tsc2005 *ts)
> {
> tsc2005_stop_scan(ts);
>
> - disable_irq(ts->spi->irq);
> + disable_irq(ts->irq);
> del_timer_sync(&ts->penup_timer);
>
> cancel_delayed_work_sync(&ts->esd_work);
>
> - enable_irq(ts->spi->irq);
> + enable_irq(ts->irq);
> }
>
> /* must be called with ts->mutex held */
> @@ -487,9 +518,9 @@ static void tsc2005_esd_work(struct work_struct *work)
> * then we should reset the controller as if from power-up and start
> * scanning again.
> */
> - dev_info(&ts->spi->dev, "TSC2005 not responding - resetting\n");
> + dev_info(ts->dev, "TSC2005 not responding - resetting\n");
>
> - disable_irq(ts->spi->irq);
> + disable_irq(ts->irq);
> del_timer_sync(&ts->penup_timer);
>
> tsc2005_update_pen_state(ts, 0, 0, 0);
> @@ -498,7 +529,7 @@ static void tsc2005_esd_work(struct work_struct *work)
> usleep_range(100, 500); /* only 10us required */
> tsc2005_set_reset(ts, true);
>
> - enable_irq(ts->spi->irq);
> + enable_irq(ts->irq);
> tsc2005_start_scan(ts);
>
> out:
> @@ -540,10 +571,10 @@ static void tsc2005_close(struct input_dev *input)
> mutex_unlock(&ts->mutex);
> }
>
> -static int tsc2005_probe(struct spi_device *spi)
> +static int tsc200x_probe_common(struct device *dev, int irq, __u16 bustype)
> {
> - const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev);
> - struct device_node *np = spi->dev.of_node;
> + const struct tsc2005_platform_data *pdata = dev_get_platdata(dev);
> + struct device_node *np = dev->of_node;
>
> struct tsc2005 *ts;
> struct input_dev *input_dev;
> @@ -558,12 +589,12 @@ static int tsc2005_probe(struct spi_device *spi)
> int error;
>
> if (!np && !pdata) {
> - dev_err(&spi->dev, "no platform data\n");
> + dev_err(dev, "no platform data\n");
> return -ENODEV;
> }
>
> - if (spi->irq <= 0) {
> - dev_err(&spi->dev, "no irq\n");
> + if (irq <= 0) {
> + dev_err(dev, "no irq\n");
> return -ENODEV;
> }
>
> @@ -584,45 +615,46 @@ static int tsc2005_probe(struct spi_device *spi)
> &esd_timeout);
> }
>
> - spi->mode = SPI_MODE_0;
> - spi->bits_per_word = 8;
> - if (!spi->max_speed_hz)
> - spi->max_speed_hz = TSC2005_SPI_MAX_SPEED_HZ;
> -
> - error = spi_setup(spi);
> - if (error)
> - return error;
> -
> - ts = devm_kzalloc(&spi->dev, sizeof(*ts), GFP_KERNEL);
> + ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
> if (!ts)
> return -ENOMEM;
>
> - input_dev = devm_input_allocate_device(&spi->dev);
> + input_dev = devm_input_allocate_device(dev);
> if (!input_dev)
> return -ENOMEM;
>
> - ts->spi = spi;
> + ts->irq = irq;
> + ts->dev = dev;
> ts->idev = input_dev;
>
> - ts->regmap = devm_regmap_init_spi(spi, &tsc2005_regmap_config);
> + if (bustype == BUS_SPI) {
> + ts->spi = to_spi_device(dev);
> + ts->regmap = devm_regmap_init_spi(ts->spi,
> + &tsc2005_regmap_config);
> + } else if (bustype == BUS_I2C) {
> + ts->i2c = to_i2c_client(dev);
> + ts->regmap = devm_regmap_init_i2c(ts->i2c,
> + &tsc2005_regmap_config);
> + }
> +
> if (IS_ERR(ts->regmap))
> return PTR_ERR(ts->regmap);
>
> ts->x_plate_ohm = x_plate_ohm;
> ts->esd_timeout = esd_timeout;
>
> - ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
> + ts->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> GPIOD_OUT_HIGH);
> if (IS_ERR(ts->reset_gpio)) {
> error = PTR_ERR(ts->reset_gpio);
> - dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error);
> + dev_err(dev, "error acquiring reset gpio: %d\n", error);
> return error;
> }
>
> - ts->vio = devm_regulator_get_optional(&spi->dev, "vio");
> + ts->vio = devm_regulator_get_optional(dev, "vio");
> if (IS_ERR(ts->vio)) {
> error = PTR_ERR(ts->vio);
> - dev_err(&spi->dev, "vio regulator missing (%d)", error);
> + dev_err(dev, "vio regulator missing (%d)", error);
> return error;
> }
>
> @@ -637,12 +669,12 @@ static int tsc2005_probe(struct spi_device *spi)
> INIT_DELAYED_WORK(&ts->esd_work, tsc2005_esd_work);
>
> snprintf(ts->phys, sizeof(ts->phys),
> - "%s/input-ts", dev_name(&spi->dev));
> + "%s/input-ts", dev_name(dev));
>
> input_dev->name = "TSC2005 touchscreen";
> input_dev->phys = ts->phys;
> - input_dev->id.bustype = BUS_SPI;
> - input_dev->dev.parent = &spi->dev;
> + input_dev->id.bustype = bustype;
> + input_dev->dev.parent = dev;
> input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
> input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
>
> @@ -661,12 +693,12 @@ static int tsc2005_probe(struct spi_device *spi)
> /* Ensure the touchscreen is off */
> tsc2005_stop_scan(ts);
>
> - error = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
> + error = devm_request_threaded_irq(dev, irq, NULL,
> tsc2005_irq_thread,
> IRQF_TRIGGER_RISING | IRQF_ONESHOT,
> "tsc2005", ts);
> if (error) {
> - dev_err(&spi->dev, "Failed to request irq, err: %d\n", error);
> + dev_err(dev, "Failed to request irq, err: %d\n", error);
> return error;
> }
>
> @@ -677,32 +709,49 @@ static int tsc2005_probe(struct spi_device *spi)
> return error;
> }
>
> - dev_set_drvdata(&spi->dev, ts);
> - error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group);
> + dev_set_drvdata(dev, ts);
> + error = sysfs_create_group(&dev->kobj, &tsc2005_attr_group);
> if (error) {
> - dev_err(&spi->dev,
> + dev_err(dev,
> "Failed to create sysfs attributes, err: %d\n", error);
> goto disable_regulator;
> }
>
> error = input_register_device(ts->idev);
> if (error) {
> - dev_err(&spi->dev,
> + dev_err(dev,
> "Failed to register input device, err: %d\n", error);
> goto err_remove_sysfs;
> }
>
> - irq_set_irq_wake(spi->irq, 1);
> + irq_set_irq_wake(irq, 1);
> return 0;
>
> err_remove_sysfs:
> - sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
> + sysfs_remove_group(&dev->kobj, &tsc2005_attr_group);
> disable_regulator:
> if (ts->vio)
> regulator_disable(ts->vio);
> return error;
> }
>
> +
> +static int tsc2005_probe(struct spi_device *spi)
> +{
> + int error;
> +
> + spi->mode = SPI_MODE_0;
> + spi->bits_per_word = 8;
> + if (!spi->max_speed_hz)
> + spi->max_speed_hz = TSC2005_SPI_MAX_SPEED_HZ;
> +
> + error = spi_setup(spi);
> + if (error)
> + return error;
> +
> + return tsc200x_probe_common(&spi->dev, spi->irq, BUS_SPI);
> +}
> +
> static int tsc2005_remove(struct spi_device *spi)
> {
> struct tsc2005 *ts = dev_get_drvdata(&spi->dev);
> @@ -759,7 +808,78 @@ static struct spi_driver tsc2005_driver = {
> .remove = tsc2005_remove,
> };
>
> -module_spi_driver(tsc2005_driver);
> +static int tsc2004_probe(struct i2c_client *i2c,
> + const struct i2c_device_id *id)
> +
> +{
> + return tsc200x_probe_common(&i2c->dev, i2c->irq, BUS_I2C);
> +}
> +
> +static int tsc2004_remove(struct i2c_client *i2c)
> +{
> + struct tsc2005 *ts = dev_get_drvdata(&i2c->dev);
> +
> + sysfs_remove_group(&i2c->dev.kobj, &tsc2005_attr_group);
> +
> + if (ts->vio)
> + regulator_disable(ts->vio);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id tsc2004_idtable[] = {
> + { "tsc2004", 0 },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, tsc2004_idtable);
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id tsc2004_of_match[] = {
> + { .compatible = "ti,tsc2004" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, tsc2004_of_match);
> +#endif
> +
> +static struct i2c_driver tsc2004_driver = {
> + .driver = {
> + .name = "tsc2004",
> + .of_match_table = of_match_ptr(tsc2004_of_match),
> + .pm = &tsc2005_pm_ops,
> + },
> + .id_table = tsc2004_idtable,
> + .probe = tsc2004_probe,
> + .remove = tsc2004_remove,
> +};
> +
> +static int __init tsc2005_modinit(void)
> +{
> + int ret = 0;
> +#if IS_ENABLED(CONFIG_I2C)
> + ret = i2c_add_driver(&tsc2004_driver);
> + if (ret != 0)
> + pr_err("Failed to register tsc2004 I2C driver: %d\n", ret);
> +#endif
> +#if defined(CONFIG_SPI_MASTER)
> + ret = spi_register_driver(&tsc2005_driver);
> + if (ret != 0)
> + pr_err("Failed to register tsc2005 SPI driver: %d\n", ret);
> +#endif
> + return ret;
> +}
> +module_init(tsc2005_modinit);
> +
> +static void __exit tsc2005_exit(void)
> +{
> +#if IS_ENABLED(CONFIG_I2C)
> + i2c_del_driver(&tsc2004_driver);
> +#endif
> +#if defined(CONFIG_SPI_MASTER)
> + spi_unregister_driver(&tsc2005_driver);
> +#endif
> +}
> +module_exit(tsc2005_exit);
>
> MODULE_AUTHOR("Lauri Leukkunen <lauri.leukkunen@xxxxxxxxx>");
> MODULE_DESCRIPTION("TSC2005 Touchscreen Driver");
> --
> 2.1.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
