On 10/15/2015 07:43 PM, Franklin S Cooper Jr. wrote: > > On 10/15/2015 07:16 PM, Dmitry Torokhov wrote: >> On Wed, Oct 14, 2015 at 08:58:32PM -0500, Franklin S Cooper Jr. wrote: >>> On 10/14/2015 06:39 PM, Dmitry Torokhov wrote: >>>> On Wed, Oct 07, 2015 at 07:21:38AM -0500, fcooper@xxxxxx wrote: >>>>> From: Franklin S Cooper Jr <fcooper@xxxxxx> >>>>> >>>>> Calculate the amount of data that needs to be read for the specified max >>>>> number of support points. If the maximum number of support points changes >>>>> then the amount that is read from the touch screen controller should >>>>> reflect this. >>>>> >>>>> Signed-off-by: Franklin S Cooper Jr <fcooper@xxxxxx> >>>>> --- >>>>> drivers/input/touchscreen/edt-ft5x06.c | 6 ++++-- >>>>> 1 file changed, 4 insertions(+), 2 deletions(-) >>>>> >>>>> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c >>>>> index 7239c31..1e0ed6e 100644 >>>>> --- a/drivers/input/touchscreen/edt-ft5x06.c >>>>> +++ b/drivers/input/touchscreen/edt-ft5x06.c >>>>> @@ -178,14 +178,16 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id) >>>>> cmd = 0xf9; /* tell the controller to send touch data */ >>>>> offset = 5; /* where the actual touch data starts */ >>>>> tplen = 4; /* data comes in so called frames */ >>>>> - datalen = 26; /* how much bytes to listen for */ >>>>> + >>>>> + /* how many bytes to listen for */ >>>>> + datalen = tplen * MAX_SUPPORT_POINTS + offset + 1; >>>>> break; >>>>> >>>>> case M09: >>>>> cmd = 0x02; >>>>> offset = 1; >>>>> tplen = 6; >>>>> - datalen = 29; >>>>> + datalen = tplen * MAX_SUPPORT_POINTS - cmd + 1; >>>>> break; >>>> Hmm, why would formulae for datalen be different depending on the >>>> firmware? And I think original 29 it too low: we need 30 bytes for 5 >>>> contacts + 1 to account for offset. >>> So based on the current ISR we don't care about the touch weight and >>> which are the last two registers for each touch point. So for the last >>> touchpoint we really don't need to read the extra two registers (-2). >> This is really not obvious. I do not think we'd see any performance >> degradation if we actually read the whole last touchpoint. > Yeah that shouldn't be a problem. I'll fix that. >>> We need +1 simply for the fact that we read the register at location >>> cmd. >> I am not sure I follow this. We do not reference anything past >> rdbuf[(MAX_SUPPORT_POINTS - 1) * tplen + offset] and >> our offset takes care of the start position, so why exactly we need the >> +1? Ah, CRC is in the extra byte. > Sorry your right the +1 isn't needed. >> Can we unify the calculation to be: >> >> datalen = tplen * MAX_SUPPORT_POINTS + offset + crc_len; > Why do we need the crc_len? M06 is the only one that uses the CRC > and the offset insures we are reading the necessary crc registers. > > Unless I'm missing something it would simply be: > > datalen = tplen * MAX_SUPPORT_POINTS + offset > >> By the way, what version of firmware you tested your changes with? Forgot to add. I'm using the M09 version. >> >>> So 6 * 5 - 2 + 1 which is how we get to 29. The formula looks slightly >>> different because the registers we are reading are very close to zero >>> so the math works out to equal the equation I used for M09. >>> >>> M06 since tplen = 4 then all four registers are used in the ISR per touch >>> point. Plus the offset and plus 1 again to account for the fact we are reading >>> the cmd register. But once again it would be nice if someone can confirm this. >>>> I also wonder why we need extra 1 byte in M06 case. >>>> >>>> Lothar? >>>> >>>> Thanks. >>>> >> Thanks. >> -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
