After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins declared, the functionality depending
on these pins will not be available, but the device can still be used
with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpio" property and the reset pin configuration is
read from the "reset-gpio" property. For ACPI 5.1, named properties
can be specified using the _DSD section. If there is no _DSD section
in the ACPI table, the driver will fall back to using indexed gpio
pins declared in the _CRS section.
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpio", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpio", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@xxxxxxxxx>
Signed-off-by: Irina Tirdea <irina.tirdea@xxxxxxxxx>
---
.../bindings/input/touchscreen/goodix.txt | 5 +
drivers/input/touchscreen/goodix.c | 176 +++++++++++++++++++++
2 files changed, 181 insertions(+)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 8ba98ee..7137881 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -12,6 +12,8 @@ Required properties:
- reg : I2C address of the chip. Should be 0x5d or 0x14
- interrupt-parent : Interrupt controller to which the chip is connected
- interrupts : Interrupt to which the chip is connected
+ - irq-gpio : GPIO pin used for IRQ
+ - reset-gpio : GPIO pin used for reset
Example:
@@ -23,6 +25,9 @@ Example:
reg = <0x5d>;
interrupt-parent = <&gpio>;
interrupts = <0 0>;
+
+ irq-gpio = <&gpio1 0 0>;
+ reset-gpio = <&gpio1 1 0>;
};
/* ... */
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 56d0330..916198d 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -16,6 +16,7 @@
#include <linux/kernel.h>
#include <linux/dmi.h>
+#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
@@ -37,8 +38,13 @@ struct goodix_ts_data {
unsigned int int_trigger_type;
bool rotated_screen;
int cfg_len;
+ struct gpio_desc *gpiod_int;
+ struct gpio_desc *gpiod_rst;
};
+#define GOODIX_GPIO_INT_NAME "irq"
+#define GOODIX_GPIO_RST_NAME "reset"
+
#define GOODIX_MAX_HEIGHT 4096
#define GOODIX_MAX_WIDTH 4096
#define GOODIX_INT_TRIGGER 1
@@ -89,6 +95,41 @@ static const struct dmi_system_id rotated_screen[] = {
{}
};
+/*
+ * Some platforms specify the gpio pins for interrupt and reset properly
+ * in ACPI, but cannot use the interrupt pin as output due to their specific
+ * HW configuration.
+ */
+static const struct dmi_system_id goodix_no_gpio_pins_support[] = {
+#if defined(CONFIG_DMI) && defined(CONFIG_X86)
+ {
+ .ident = "Onda v975w",
+ .matches = {
+ DMI_MATCH(DMI_BIOS_VENDOR, "American Megatrends Inc."),
+ DMI_MATCH(DMI_PRODUCT_UUID,
+ "03000200-0400-0500-0006-000700080009"),
+ DMI_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
+ DMI_MATCH(DMI_BOARD_NAME, "Aptio CRB"),
+ }
+ },
+ {
+ .ident = "WinBook TW100",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TW100")
+ }
+ },
+ {
+ .ident = "WinBook TW700",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TW700")
+ },
+ },
+#endif
+ {}
+};
+
/**
* goodix_i2c_read - read data from a register of the i2c slave device.
*
@@ -237,6 +278,114 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+ int error;
+
+ error = gpiod_direction_output(ts->gpiod_int, 0);
+ if (error)
+ return error;
+ msleep(50); /* T5: 50ms */
+
+ return gpiod_direction_input(ts->gpiod_int);
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+ int error;
+
+ /* begin select I2C slave addr */
+ error = gpiod_direction_output(ts->gpiod_rst, 0);
+ if (error)
+ return error;
+ msleep(20); /* T2: > 10ms */
+ /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+ error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+ if (error)
+ return error;
+ usleep_range(100, 2000); /* T3: > 100us */
+ error = gpiod_direction_output(ts->gpiod_rst, 1);
+ if (error)
+ return error;
+ usleep_range(6000, 10000); /* T4: > 5ms */
+ /* end select I2C slave addr */
+ error = gpiod_direction_input(ts->gpiod_rst);
+ if (error)
+ return error;
+ return goodix_int_sync(ts);
+}
+
+static const struct acpi_gpio_params goodix_first_gpio = { 0, 0, false };
+static const struct acpi_gpio_params goodix_second_gpio = { 1, 0, false };
+
+static const struct acpi_gpio_mapping goodix_default_gpios[] = {
+ { GOODIX_GPIO_INT_NAME "-gpio", &goodix_first_gpio, 1 },
+ { GOODIX_GPIO_RST_NAME "-gpio", &goodix_second_gpio, 1 },
+ { },
+};
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts)
+{
+ int error;
+ struct device *dev;
+ struct gpio_desc *gpiod;
+
+ if (!ts->client)
+ return -EINVAL;
+ dev = &ts->client->dev;
+
+ if (dmi_check_system(goodix_no_gpio_pins_support)) {
+ dev_dbg(&ts->client->dev, "GPIO pins not supported.\n");
+ return 0;
+ }
+
+ if (ACPI_HANDLE(dev)) {
+ error = acpi_dev_add_driver_gpios(ACPI_COMPANION(dev),
+ goodix_default_gpios);
+ if (error)
+ return error;
+ }
+
+ /* Get the interrupt GPIO pin number */
+ gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ error = PTR_ERR(gpiod);
+ if (error != -EPROBE_DEFER)
+ dev_warn(dev, "Failed to get %s GPIO: %d\n",
+ GOODIX_GPIO_INT_NAME, error);
+ goto out_err;
+ }
+ ts->gpiod_int = gpiod;
+
+ /* Get the reset line GPIO pin number */
+ gpiod = devm_gpiod_get(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ error = PTR_ERR(gpiod);
+ if (error != -EPROBE_DEFER)
+ dev_warn(dev, "Failed to get %s GPIO: %d\n",
+ GOODIX_GPIO_RST_NAME, error);
+ goto out_err;
+ }
+ ts->gpiod_rst = gpiod;
+
+ return 0;
+
+out_err:
+ if (ACPI_HANDLE(dev))
+ acpi_dev_remove_driver_gpios(ACPI_COMPANION(dev));
+ return error;
+}
+
/**
* goodix_read_config - Read the embedded configuration of the panel
*
@@ -405,6 +554,19 @@ static int goodix_ts_probe(struct i2c_client *client,
ts->client = client;
i2c_set_clientdata(client, ts);
+ error = goodix_get_gpio_config(ts);
+ if (error == -EPROBE_DEFER)
+ return error;
+
+ if (ts->gpiod_int && ts->gpiod_rst) {
+ /* reset the controller */
+ error = goodix_reset(ts);
+ if (error) {
+ dev_err(&client->dev, "Controller reset failed.\n");
+ return error;
+ }
+ }
+
error = goodix_i2c_test(client);
if (error) {
dev_err(&client->dev, "I2C communication failure: %d\n", error);
@@ -437,6 +599,19 @@ static int goodix_ts_probe(struct i2c_client *client,
return 0;
}
+static int goodix_ts_remove(struct i2c_client *client)
+{
+ struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+ if (!ts->gpiod_int || !ts->gpiod_rst)
+ return 0;
+
+ if (ACPI_HANDLE(&ts->client->dev))
+ acpi_dev_remove_driver_gpios(ACPI_COMPANION(&ts->client->dev));
+
+ return 0;
+}
+
static const struct i2c_device_id goodix_ts_id[] = {
{ "GDIX1001:00", 0 },
{ }
@@ -467,6 +642,7 @@ MODULE_DEVICE_TABLE(of, goodix_of_match);
static struct i2c_driver goodix_ts_driver = {
.probe = goodix_ts_probe,
+ .remove = goodix_ts_remove,
.id_table = goodix_ts_id,
.driver = {
.name = "Goodix-TS",
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
