On Tue, 2015-09-29 at 17:47 +0000, Tirdea, Irina wrote: > > > -----Original Message----- > > From: Bastien Nocera [mailto:hadess@xxxxxxxxxx] > > Sent: 29 September, 2015 5:04 > > To: Tirdea, Irina; linux-input@xxxxxxxxxxxxxxx > > Cc: linux-kernel@xxxxxxxxxxxxxxx; Rob Herring; Pawel Moll; Ian > > Campbell; Kumar Gala; Purdila, Octavian; Dmitry Torokhov; Mark > > Rutland; devicetree@xxxxxxxxxxxxxxx > > Subject: Re: [PATCH v3 1/5] Input: goodix - reset device at init > > > > On Fri, 2015-09-25 at 21:04 +0000, Tirdea, Irina wrote: > > > > <snip> > > > > > > The warning from your dmesg output will not cause probe to fail. > > > If you look at the code for byt_gpio_direction_output, it will > > > just > > > print > > > a warning and continue [1]: > > > WARN(readl(conf_reg) & BYT_DIRECT_IRQ_EN, > > > "Potential Error: Setting GPIO with direct_irq_en to > > > output"); > > > I thought probe finishes successfully, but due to the warning in > > > dmesg you > > > are not sure whether the IRQ GPIO pin can be used as output. > > > If probe fails, it must be for another reason than the > > > direct_irq_en > > > warning. > > > > > > > Would you have a patch for me to test that would bypass this > > > > error, > > > > or > > > > at least fallback gracefully to not resetting, not probing > > > > GPIOs if > > > > they're badly setup? > > > > > > If the driver fails to initialize the GPIOs, it will at least > > > print > > > some > > > "Failed to get GPIO" warnings in dmesg. Do you have such messages > > > in > > > dmesg or any additional information on why probe fails? > > > > > > The current code will ignore GPIOs if they are not defined in > > > ACPI > > > (see the check for -ENOENT), but does not ignore other error > > > codes. > > > If you want to bypass all GPIO errors, you can use the code > > > below. > > > > The failure isn't there, it's when running goodix_i2c_test(): > > Sep 25 16:39:20 winbook kernel: Goodix-TS i2c-GDIX1001:00: i2c test > > failed attempt 1: -121 > > Sep 25 16:39:20 winbook kernel: Goodix-TS i2c-GDIX1001:00: i2c test > > failed attempt 2: -121 > > Sep 25 16:39:20 winbook kernel: Goodix-TS i2c-GDIX1001:00: I2C > > communication failure: -121 > > Sep 25 16:39:20 winbook kernel: Goodix-TS: probe of i2c-GDIX1001:00 > > failed with error -121 > > > > Are you using v6 of the patches? There was an issue with reset that > Aleksei reported > and was fixed in v6 (although he had a different i2c error and a > different scenario). Pretty certain. Your current patchset is at: https://github.com/hadess/gt9xx/tree/irina-tirdea And the patches are yours, with the prefix and Documentation removed. > > The GPIO setup seems to work (bar the warnings), and the reset as > > well, > > but then the device fails to communicate. Likely a fallout from the > > reset actually failing. > > > > Swapping around the RST and INT pins leads to the same problem. > > Either > > this device's GPIO PINs aren't actually functional, and the > > firmware > > contains garbage, or something else is wrong. > > > > I agree. Either the interrupt pin cannot be used as output in your > configuration > or there are some specifics in the ACPI tables that prevent using > these pins. > > > I'm not sure how we can detect, and blacklist, those devices. At > > least > > my original device, the Onda v975w, and the WinBook TW100 would > > have > > those problems. > > > > I can use DMI quirks to exclude these devices from using the features > that > depend on the gpio pins. I already have the DMI information for > WinBook TW100 > and WinBook TW700. Could you tell me the DMI_SYS_VENDOR and > DMI_PRODUCT_NAME for Onda v975w so I can add it as well? I don't have access to the Onda v975w anymore, but let me CC: a few people that could also help with testing. Carlos, Cosimo, Christian, there's a patchset for you to test on the Onda v975w at: https://github.com/hadess/gt9xx/commits/irina-tirdea Doing an "rmmod goodix ; insmod ./goodix_backport.ko" should be enough to test whether the patch set works. If it doesn't work correctly, you'll need to reboot the machine, swap the irq_idx and rst_idx values at: https://github.com/hadess/gt9xx/commit/c27de79f494c2b2e7a198ff4d27976ae93669dbd#diff-dddc2849e36327439530f3e2faacec4fR321 and try again. If all that fails, could you please send the output of "dmidecode" to Irina? Cheers -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
