Re: [PATCH 1/6] Input: edt-ft5x06 - switch to newer gpio framework

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Sep 21, 2015 at 03:55:33PM -0700, Dmitry Torokhov wrote:
> On Sat, Sep 12, 2015 at 10:45:46AM -0700, Dmitry Torokhov wrote:
> > From: Franklin S Cooper Jr <fcooper@xxxxxx>
> > 
> > The current/old gpio framework used doesn't properly listen to
> > ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
> > account these flags when setting gpio values.
> > 
> > Since the values being output were based on voltage and not logic they
> > change to reflect this difference. Also use gpiod_set_value_cansleep since
> > wake and reset pins can be provided by bus based io expanders.
> > 
> > Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
> > warning.
> > 
> > Signed-off-by: Franklin S Cooper Jr <fcooper@xxxxxx>
> > Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
> 
> Franklin, could you please give this series a spin so I can queue it for
> the next merge window?
> 
> Thanks!
>
Sorry. Patch set worked fine for me.

Signed-off-by: Franklin S Cooper Jr <fcooper@xxxxxx> 
> > ---
> >  .../bindings/input/touchscreen/edt-ft5x06.txt      |   4 +-
> >  drivers/input/touchscreen/edt-ft5x06.c             | 129 ++++++---------------
> >  include/linux/input/edt-ft5x06.h                   |   3 -
> >  3 files changed, 40 insertions(+), 96 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > index 76db967..9330d4d 100644
> > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > @@ -50,6 +50,6 @@ Example:
> >  		pinctrl-0 = <&edt_ft5x06_pins>;
> >  		interrupt-parent = <&gpio2>;
> >  		interrupts = <5 0>;
> > -		reset-gpios = <&gpio2 6 1>;
> > -		wake-gpios = <&gpio4 9 0>;
> > +		reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
> > +		wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> >  	};
> > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > index 48de1e8..5738722 100644
> > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > @@ -34,8 +34,7 @@
> >  #include <linux/delay.h>
> >  #include <linux/debugfs.h>
> >  #include <linux/slab.h>
> > -#include <linux/gpio.h>
> > -#include <linux/of_gpio.h>
> > +#include <linux/gpio/consumer.h>
> >  #include <linux/input/mt.h>
> >  #include <linux/input/touchscreen.h>
> >  #include <linux/input/edt-ft5x06.h>
> > @@ -91,9 +90,9 @@ struct edt_ft5x06_ts_data {
> >  	u16 num_x;
> >  	u16 num_y;
> >  
> > -	int reset_pin;
> > -	int irq_pin;
> > -	int wake_pin;
> > +	struct gpio_desc *reset_gpio;
> > +	struct gpio_desc *wake_gpio;
> > +	struct gpio_desc *irq_gpio;
> >  
> >  #if defined(CONFIG_DEBUG_FS)
> >  	struct dentry *debug_dir;
> > @@ -752,45 +751,6 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
> >  
> >  #endif /* CONFIG_DEBUGFS */
> >  
> > -static int edt_ft5x06_ts_reset(struct i2c_client *client,
> > -			struct edt_ft5x06_ts_data *tsdata)
> > -{
> > -	int error;
> > -
> > -	if (gpio_is_valid(tsdata->wake_pin)) {
> > -		error = devm_gpio_request_one(&client->dev,
> > -					tsdata->wake_pin, GPIOF_OUT_INIT_LOW,
> > -					"edt-ft5x06 wake");
> > -		if (error) {
> > -			dev_err(&client->dev,
> > -				"Failed to request GPIO %d as wake pin, error %d\n",
> > -				tsdata->wake_pin, error);
> > -			return error;
> > -		}
> > -
> > -		msleep(5);
> > -		gpio_set_value(tsdata->wake_pin, 1);
> > -	}
> > -	if (gpio_is_valid(tsdata->reset_pin)) {
> > -		/* this pulls reset down, enabling the low active reset */
> > -		error = devm_gpio_request_one(&client->dev,
> > -					tsdata->reset_pin, GPIOF_OUT_INIT_LOW,
> > -					"edt-ft5x06 reset");
> > -		if (error) {
> > -			dev_err(&client->dev,
> > -				"Failed to request GPIO %d as reset pin, error %d\n",
> > -				tsdata->reset_pin, error);
> > -			return error;
> > -		}
> > -
> > -		msleep(5);
> > -		gpio_set_value(tsdata->reset_pin, 1);
> > -		msleep(300);
> > -	}
> > -
> > -	return 0;
> > -}
> > -
> >  static int edt_ft5x06_ts_identify(struct i2c_client *client,
> >  					struct edt_ft5x06_ts_data *tsdata,
> >  					char *fw_version)
> > @@ -931,30 +891,6 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> >  	}
> >  }
> >  
> > -#ifdef CONFIG_OF
> > -static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> > -				struct edt_ft5x06_ts_data *tsdata)
> > -{
> > -	struct device_node *np = dev->of_node;
> > -
> > -	/*
> > -	 * irq_pin is not needed for DT setup.
> > -	 * irq is associated via 'interrupts' property in DT
> > -	 */
> > -	tsdata->irq_pin = -EINVAL;
> > -	tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
> > -	tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
> > -
> > -	return 0;
> > -}
> > -#else
> > -static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> > -					struct edt_ft5x06_ts_data *tsdata)
> > -{
> > -	return -ENODEV;
> > -}
> > -#endif
> > -
> >  static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  					 const struct i2c_device_id *id)
> >  {
> > @@ -973,32 +909,42 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  		return -ENOMEM;
> >  	}
> >  
> > -	if (!pdata) {
> > -		error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
> > -		if (error) {
> > -			dev_err(&client->dev,
> > -				"DT probe failed and no platform data present\n");
> > -			return error;
> > -		}
> > -	} else {
> > -		tsdata->reset_pin = pdata->reset_pin;
> > -		tsdata->irq_pin = pdata->irq_pin;
> > -		tsdata->wake_pin = -EINVAL;
> > +	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> > +						     "reset", GPIOD_OUT_HIGH);
> > +	if (IS_ERR(tsdata->reset_gpio)) {
> > +		error = PTR_ERR(tsdata->reset_gpio);
> > +		dev_err(&client->dev,
> > +			"Failed to request GPIO reset pin, error %d\n", error);
> > +		return error;
> >  	}
> >  
> > -	error = edt_ft5x06_ts_reset(client, tsdata);
> > -	if (error)
> > +	tsdata->wake_gpio = devm_gpiod_get_optional(&client->dev,
> > +						    "wake", GPIOD_OUT_LOW);
> > +	if (IS_ERR(tsdata->wake_gpio)) {
> > +		error = PTR_ERR(tsdata->wake_gpio);
> > +		dev_err(&client->dev,
> > +			"Failed to request GPIO wake pin, error %d\n", error);
> >  		return error;
> > +	}
> >  
> > -	if (gpio_is_valid(tsdata->irq_pin)) {
> > -		error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
> > -					GPIOF_IN, "edt-ft5x06 irq");
> > -		if (error) {
> > -			dev_err(&client->dev,
> > -				"Failed to request GPIO %d, error %d\n",
> > -				tsdata->irq_pin, error);
> > -			return error;
> > -		}
> > +	tsdata->irq_gpio = devm_gpiod_get_optional(&client->dev,
> > +						   "irq", GPIOD_IN);
> > +	if (IS_ERR(tsdata->irq_gpio)) {
> > +		error = PTR_ERR(tsdata->irq_gpio);
> > +		dev_err(&client->dev,
> > +			"Failed to request GPIO irq pin, error %d\n", error);
> > +		return error;
> > +	}
> > +
> > +	if (tsdata->wake_gpio) {
> > +		usleep_range(5000, 6000);
> > +		gpiod_set_value_cansleep(tsdata->wake_gpio, 1);
> > +	}
> > +
> > +	if (tsdata->reset_gpio) {
> > +		usleep_range(5000, 6000);
> > +		gpiod_set_value_cansleep(tsdata->reset_gpio, 0);
> > +		msleep(300);
> >  	}
> >  
> >  	input = devm_input_allocate_device(&client->dev);
> > @@ -1074,7 +1020,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  
> >  	dev_dbg(&client->dev,
> >  		"EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
> > -		client->irq, tsdata->wake_pin, tsdata->reset_pin);
> > +		client->irq, desc_to_gpio(tsdata->wake_gpio),
> > +		desc_to_gpio(tsdata->reset_gpio));
> >  
> >  	return 0;
> >  
> > diff --git a/include/linux/input/edt-ft5x06.h b/include/linux/input/edt-ft5x06.h
> > index 8a1e0d1..5ca5b4c 100644
> > --- a/include/linux/input/edt-ft5x06.h
> > +++ b/include/linux/input/edt-ft5x06.h
> > @@ -10,9 +10,6 @@
> >   */
> >  
> >  struct edt_ft5x06_platform_data {
> > -	int irq_pin;
> > -	int reset_pin;
> > -
> >  	/* startup defaults for operational parameters */
> >  	bool use_parameters;
> >  	u8 gain;
> > -- 
> > 2.6.0.rc0.131.gf624c3d
> > 
> 
> -- 
> Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux