From: Pavel Rojtberg <rojtberg@xxxxxxxxx>
this code was probably wrong ever since and is redundant with
xpad_send_led_command.
Both try to send a similar command to the xbox360 controller. However
xpad_send_led_command correctly uses the pad_nr instead of
bInterfaceNumber to select the led and re-uses the irq_out URB instead
of creating a new one.
Note that this change only affects the two supported wireless
controllers. Tested using the xbox360 wireless controller (PC).
Signed-off-by: Pavel Rojtberg <rojtberg@xxxxxxxxx>
---
drivers/input/joystick/xpad.c | 79 +-----------------------------------------------------------------
1 file changed, 1 insertion(+), 78 deletions(-)
diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c
index 4cb450c..9c95db7 100644
--- a/drivers/input/joystick/xpad.c
+++ b/drivers/input/joystick/xpad.c
@@ -329,9 +329,6 @@ struct usb_xpad {
unsigned char *idata; /* input data */
dma_addr_t idata_dma;
- struct urb *bulk_out;
- unsigned char *bdata;
-
struct urb *irq_out; /* urb for interrupt out report */
unsigned char *odata; /* output data */
dma_addr_t odata_dma;
@@ -511,7 +508,6 @@ static void xpad360w_process_packet(struct usb_xpad *xpad, u16 cmd, unsigned cha
if (data[0] & 0x08) {
if (data[1] & 0x80) {
xpad->pad_present = 1;
- usb_submit_urb(xpad->bulk_out, GFP_ATOMIC);
xpad_identify_controller(xpad);
} else
xpad->pad_present = 0;
@@ -669,28 +665,6 @@ exit:
__func__, retval);
}
-static void xpad_bulk_out(struct urb *urb)
-{
- struct usb_xpad *xpad = urb->context;
- struct device *dev = &xpad->intf->dev;
-
- switch (urb->status) {
- case 0:
- /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* this urb is terminated, clean up */
- dev_dbg(dev, "%s - urb shutting down with status: %d\n",
- __func__, urb->status);
- break;
- default:
- dev_dbg(dev, "%s - nonzero urb status received: %d\n",
- __func__, urb->status);
- }
-}
-
static void xpad_irq_out(struct urb *urb)
{
struct usb_xpad *xpad = urb->context;
@@ -1216,52 +1190,6 @@ static int xpad_probe(struct usb_interface *intf, const struct usb_device_id *id
if (xpad->xtype == XTYPE_XBOX360W) {
/*
- * Setup the message to set the LEDs on the
- * controller when it shows up
- */
- xpad->bulk_out = usb_alloc_urb(0, GFP_KERNEL);
- if (!xpad->bulk_out) {
- error = -ENOMEM;
- goto fail7;
- }
-
- xpad->bdata = kzalloc(XPAD_PKT_LEN, GFP_KERNEL);
- if (!xpad->bdata) {
- error = -ENOMEM;
- goto fail8;
- }
-
- xpad->bdata[2] = 0x08;
- switch (intf->cur_altsetting->desc.bInterfaceNumber) {
- case 0:
- xpad->bdata[3] = 0x42;
- break;
- case 2:
- xpad->bdata[3] = 0x43;
- break;
- case 4:
- xpad->bdata[3] = 0x44;
- break;
- case 6:
- xpad->bdata[3] = 0x45;
- }
-
- ep_irq_in = &intf->cur_altsetting->endpoint[1].desc;
- if (usb_endpoint_is_bulk_out(ep_irq_in)) {
- usb_fill_bulk_urb(xpad->bulk_out, udev,
- usb_sndbulkpipe(udev,
- ep_irq_in->bEndpointAddress),
- xpad->bdata, XPAD_PKT_LEN,
- xpad_bulk_out, xpad);
- } else {
- usb_fill_int_urb(xpad->bulk_out, udev,
- usb_sndintpipe(udev,
- ep_irq_in->bEndpointAddress),
- xpad->bdata, XPAD_PKT_LEN,
- xpad_bulk_out, xpad, 0);
- }
-
- /*
* Submit the int URB immediately rather than waiting for open
* because we get status messages from the device whether
* or not any controllers are attached. In fact, it's
@@ -1271,13 +1199,11 @@ static int xpad_probe(struct usb_interface *intf, const struct usb_device_id *id
xpad->irq_in->dev = xpad->udev;
error = usb_submit_urb(xpad->irq_in, GFP_KERNEL);
if (error)
- goto fail9;
+ goto fail7;
}
return 0;
- fail9: kfree(xpad->bdata);
- fail8: usb_free_urb(xpad->bulk_out);
fail7: input_unregister_device(input_dev);
input_dev = NULL;
fail6: xpad_led_disconnect(xpad);
@@ -1301,8 +1227,6 @@ static void xpad_disconnect(struct usb_interface *intf)
xpad_deinit_output(xpad);
if (xpad->xtype == XTYPE_XBOX360W) {
- usb_kill_urb(xpad->bulk_out);
- usb_free_urb(xpad->bulk_out);
usb_kill_urb(xpad->irq_in);
}
@@ -1310,7 +1234,6 @@ static void xpad_disconnect(struct usb_interface *intf)
usb_free_coherent(xpad->udev, XPAD_PKT_LEN,
xpad->idata, xpad->idata_dma);
- kfree(xpad->bdata);
kfree(xpad);
usb_set_intfdata(intf, NULL);
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
