Sorry ignoring this patch. Will resend with proper version 2 change information.
On 08/31/2015 06:17 PM, Franklin S Cooper Jr wrote:
> The current/old gpio framework used doesn't properly listen to
> ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
> account these flags when setting gpio values.
>
> Since the values being outputed were base on voltage and not logic the
> values being outputted must change to refect this difference. Also use
> gpiod_set_value_cansleep since wake and reset pins can be provided by
> bus based io expanders.
>
> Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
> warning.
>
> Signed-off-by: Franklin S Cooper Jr <fcooper@xxxxxx>
> ---
> .../bindings/input/touchscreen/edt-ft5x06.txt | 4 +-
> drivers/input/touchscreen/edt-ft5x06.c | 132 +++++++--------------
> include/linux/input/edt-ft5x06.h | 4 +-
> 3 files changed, 47 insertions(+), 93 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> index 76db967..9330d4d 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> @@ -50,6 +50,6 @@ Example:
> pinctrl-0 = <&edt_ft5x06_pins>;
> interrupt-parent = <&gpio2>;
> interrupts = <5 0>;
> - reset-gpios = <&gpio2 6 1>;
> - wake-gpios = <&gpio4 9 0>;
> + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> };
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 394b1de..d64d29a 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -91,9 +91,9 @@ struct edt_ft5x06_ts_data {
> u16 num_x;
> u16 num_y;
>
> - int reset_pin;
> - int irq_pin;
> - int wake_pin;
> + struct gpio_desc *reset_pin;
> + struct gpio_desc *wake_pin;
> + struct gpio_desc *irq_pin;
>
> #if defined(CONFIG_DEBUG_FS)
> struct dentry *debug_dir;
> @@ -752,45 +752,6 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
>
> #endif /* CONFIG_DEBUGFS */
>
> -static int edt_ft5x06_ts_reset(struct i2c_client *client,
> - struct edt_ft5x06_ts_data *tsdata)
> -{
> - int error;
> -
> - if (gpio_is_valid(tsdata->wake_pin)) {
> - error = devm_gpio_request_one(&client->dev,
> - tsdata->wake_pin, GPIOF_OUT_INIT_LOW,
> - "edt-ft5x06 wake");
> - if (error) {
> - dev_err(&client->dev,
> - "Failed to request GPIO %d as wake pin, error %d\n",
> - tsdata->wake_pin, error);
> - return error;
> - }
> -
> - msleep(5);
> - gpio_set_value(tsdata->wake_pin, 1);
> - }
> - if (gpio_is_valid(tsdata->reset_pin)) {
> - /* this pulls reset down, enabling the low active reset */
> - error = devm_gpio_request_one(&client->dev,
> - tsdata->reset_pin, GPIOF_OUT_INIT_LOW,
> - "edt-ft5x06 reset");
> - if (error) {
> - dev_err(&client->dev,
> - "Failed to request GPIO %d as reset pin, error %d\n",
> - tsdata->reset_pin, error);
> - return error;
> - }
> -
> - msleep(5);
> - gpio_set_value(tsdata->reset_pin, 1);
> - msleep(300);
> - }
> -
> - return 0;
> -}
> -
> static int edt_ft5x06_ts_identify(struct i2c_client *client,
> struct edt_ft5x06_ts_data *tsdata,
> char *fw_version)
> @@ -931,30 +892,6 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> }
> }
>
> -#ifdef CONFIG_OF
> -static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> - struct edt_ft5x06_ts_data *tsdata)
> -{
> - struct device_node *np = dev->of_node;
> -
> - /*
> - * irq_pin is not needed for DT setup.
> - * irq is associated via 'interrupts' property in DT
> - */
> - tsdata->irq_pin = -EINVAL;
> - tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
> - tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
> -
> - return 0;
> -}
> -#else
> -static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
> - struct edt_ft5x06_ts_data *tsdata)
> -{
> - return -ENODEV;
> -}
> -#endif
> -
> static int edt_ft5x06_ts_probe(struct i2c_client *client,
> const struct i2c_device_id *id)
> {
> @@ -964,6 +901,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> struct input_dev *input;
> int error;
> char fw_version[EDT_NAME_LEN];
> + struct gpio_desc *gpio;
>
> dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
>
> @@ -973,32 +911,47 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> return -ENOMEM;
> }
>
> - if (!pdata) {
> - error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
> - if (error) {
> - dev_err(&client->dev,
> - "DT probe failed and no platform data present\n");
> - return error;
> - }
> - } else {
> - tsdata->reset_pin = pdata->reset_pin;
> - tsdata->irq_pin = pdata->irq_pin;
> - tsdata->wake_pin = -EINVAL;
> + gpio = devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(gpio)) {
> + error = PTR_ERR(gpio);
> + dev_err(&client->dev,
> + "Failed to request GPIO reset pin, error %d\n", error);
> + return error;
> }
>
> - error = edt_ft5x06_ts_reset(client, tsdata);
> - if (error)
> + tsdata->reset_pin = gpio;
> +
> + gpio = devm_gpiod_get_optional(&client->dev, "wake", GPIOD_OUT_LOW);
> +
> + if (IS_ERR(gpio)) {
> + error = PTR_ERR(gpio);
> + dev_err(&client->dev,
> + "Failed to request GPIO wake pin, error %d\n", error);
> return error;
> + }
>
> - if (gpio_is_valid(tsdata->irq_pin)) {
> - error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
> - GPIOF_IN, "edt-ft5x06 irq");
> - if (error) {
> - dev_err(&client->dev,
> - "Failed to request GPIO %d, error %d\n",
> - tsdata->irq_pin, error);
> - return error;
> - }
> + tsdata->wake_pin = gpio;
> +
> + gpio = devm_gpiod_get_optional(&client->dev, "irq", GPIOD_IN);
> +
> + if (IS_ERR(gpio)) {
> + error = PTR_ERR(gpio);
> + dev_err(&client->dev,
> + "Failed to request GPIO irq pin, error %d\n", error);
> + return error;
> + }
> +
> + tsdata->irq_pin = gpio;
> +
> + if (tsdata->wake_pin) {
> + usleep_range(5000, 6000);
> + gpiod_set_value_cansleep(tsdata->wake_pin, 1);
> + }
> +
> + if (tsdata->reset_pin) {
> + usleep_range(5000, 6000);
> + gpiod_set_value_cansleep(tsdata->reset_pin, 0);
> + msleep(300);
> }
>
> input = devm_input_allocate_device(&client->dev);
> @@ -1074,7 +1027,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>
> dev_dbg(&client->dev,
> "EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
> - client->irq, tsdata->wake_pin, tsdata->reset_pin);
> + client->irq, desc_to_gpio(tsdata->wake_pin),
> + desc_to_gpio(tsdata->reset_pin));
>
> return 0;
>
> diff --git a/include/linux/input/edt-ft5x06.h b/include/linux/input/edt-ft5x06.h
> index 8a1e0d1..058473a 100644
> --- a/include/linux/input/edt-ft5x06.h
> +++ b/include/linux/input/edt-ft5x06.h
> @@ -10,8 +10,8 @@
> */
>
> struct edt_ft5x06_platform_data {
> - int irq_pin;
> - int reset_pin;
> + int irq_gpio;
> + int reset_gpio;
>
> /* startup defaults for operational parameters */
> bool use_parameters;
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
