On Thursday 09 July 2015 17:41:28 Andrew Duggan wrote:
> On 07/09/2015 03:40 PM, Gabriele Mazzotta wrote:
> > On Thursday 09 July 2015 15:14:17 Andrew Duggan wrote:
> >> When a device is reset the values of control registers will be reset to
> >> the defaults. This patch reapplies the control register values set for F11
> >> by the driver.
> > Hi,
> >
> > thanks for this, it works as intended. I just added a couple of
> > comments here below, but other than that
> >
> > Tested-by: Gabriele Mazzotta <gabriele.mzt@xxxxxxxxx>
>
> Thanks for testing!
>
> >> Signed-off-by: Andrew Duggan <aduggan@xxxxxxxxxxxxx>
> >> ---
> >> drivers/hid/hid-rmi.c | 41 ++++++++++++++++++++++++++++++++++-------
> >> 1 file changed, 34 insertions(+), 7 deletions(-)
> >>
> >> diff --git a/drivers/hid/hid-rmi.c b/drivers/hid/hid-rmi.c
> >> index af191a2..80c068f 100644
> >> --- a/drivers/hid/hid-rmi.c
> >> +++ b/drivers/hid/hid-rmi.c
> >> @@ -40,6 +40,8 @@
> >> #define RMI_DEVICE BIT(0)
> >> #define RMI_DEVICE_HAS_PHYS_BUTTONS BIT(1)
> >>
> >> +#define RMI_F11_CTRL_REG_COUNT 12
> >> +
> >> enum rmi_mode_type {
> >> RMI_MODE_OFF = 0,
> >> RMI_MODE_ATTN_REPORTS = 1,
> >> @@ -116,6 +118,8 @@ struct rmi_data {
> >> unsigned int max_y;
> >> unsigned int x_size_mm;
> >> unsigned int y_size_mm;
> >> + bool read_f11_ctrl_regs;
> >> + u8 f11_ctrl_regs[RMI_F11_CTRL_REG_COUNT];
> >>
> >> unsigned int gpio_led_count;
> >> unsigned int button_count;
> >> @@ -557,6 +561,15 @@ static int rmi_set_sleep_mode(struct hid_device *hdev, int sleep_mode)
> >>
> >> static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
> >> {
> >> + struct rmi_data *data = hid_get_drvdata(hdev);
> >> + int ret;
> >> +
> >> + ret = rmi_read_block(hdev, data->f11.control_base_addr,
> >> + data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
> >> + if (ret)
> >> + hid_warn(hdev, "can not read F11 control registers\n");
> > It seems that rmi_read_block() can fail because of timeouts after it
> > has started filling the buffer, so isn't it better to set
> > read_f11_ctrl_regs to false when it happens?
> >
>
> Another option would be to create a local buffer for the read and only
> copy it to data->f11_ctrl_regs if we get all of the bytes. That way we
> can ensure that rmi_post_reset will have a valid set of registers to
> restore. Or we could also just remove the read from the suspend callback
> altogether and just write the values we set in rmi_populate_f11 and not
> worry about changes made outside the driver.
The first solution you propose is what I did in my early changes before
I reported the problem. Even if I doubt that there are many users out
there changing the configuration with extrnal tools, I think that
saving and restoring the configuration is better.
> >> +
> >> +
> >> if (!device_may_wakeup(hdev->dev.parent))
> >> return rmi_set_sleep_mode(hdev, RMI_SLEEP_DEEP_SLEEP);
> >>
> >> @@ -565,6 +578,7 @@ static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
> >>
> >> static int rmi_post_reset(struct hid_device *hdev)
> >> {
> >> + struct rmi_data *data = hid_get_drvdata(hdev);
> >> int ret;
> >>
> >> ret = rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
> >> @@ -573,6 +587,14 @@ static int rmi_post_reset(struct hid_device *hdev)
> >> return ret;
> >> }
> >>
> >> + if (data->read_f11_ctrl_regs) {
> >> + ret = rmi_write_block(hdev, data->f11.control_base_addr,
> >> + data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
> >> + if (ret)
> >> + hid_warn(hdev,
> >> + "can not write F11 control registers after reset\n");
> >> + }
> >> +
> >> if (!device_may_wakeup(hdev->dev.parent)) {
> >> ret = rmi_set_sleep_mode(hdev, RMI_SLEEP_NORMAL);
> >> if (ret) {
> >> @@ -963,18 +985,23 @@ static int rmi_populate_f11(struct hid_device *hdev)
> >> * and there is no way to know if the first 20 bytes are here or not.
> >> * We use only the first 12 bytes, so get only them.
> >> */
> > Just a suggestion here. What about moving this comment right above the
> > definition of RMI_F11_CTRL_REG_COUNT?
>
> That makes sense. I can make this change in my v2.
>
> >> - ret = rmi_read_block(hdev, data->f11.control_base_addr, buf, 12);
> >> + ret = rmi_read_block(hdev, data->f11.control_base_addr,
> >> + data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
> >> if (ret) {
> >> hid_err(hdev, "can not read ctrl block of size 11: %d.\n", ret);
> >> return ret;
> >> }
> >>
> >> - data->max_x = buf[6] | (buf[7] << 8);
> >> - data->max_y = buf[8] | (buf[9] << 8);
> >> + /* data->f11_ctrl_regs now contains valid register data */
> >> + data->read_f11_ctrl_regs = true;
> >> +
> >> + data->max_x = data->f11_ctrl_regs[6] | (data->f11_ctrl_regs[7] << 8);
> >> + data->max_y = data->f11_ctrl_regs[8] | (data->f11_ctrl_regs[9] << 8);
> >>
> >> if (has_dribble) {
> >> - buf[0] = buf[0] & ~BIT(6);
> >> - ret = rmi_write(hdev, data->f11.control_base_addr, buf);
> >> + data->f11_ctrl_regs[0] = data->f11_ctrl_regs[0] & ~BIT(6);
> >> + ret = rmi_write(hdev, data->f11.control_base_addr,
> >> + data->f11_ctrl_regs);
> >> if (ret) {
> >> hid_err(hdev, "can not write to control reg 0: %d.\n",
> >> ret);
> >> @@ -983,9 +1010,9 @@ static int rmi_populate_f11(struct hid_device *hdev)
> >> }
> >>
> >> if (has_palm_detect) {
> >> - buf[11] = buf[11] & ~BIT(0);
> >> + data->f11_ctrl_regs[11] = data->f11_ctrl_regs[11] & ~BIT(0);
> >> ret = rmi_write(hdev, data->f11.control_base_addr + 11,
> >> - &buf[11]);
> >> + &data->f11_ctrl_regs[11]);
> >> if (ret) {
> >> hid_err(hdev, "can not write to control reg 11: %d.\n",
> >> ret);
> >>
> Andrew
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
