After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI 5.1/device tree).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpio", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpio", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@xxxxxxxxx>
Signed-off-by: Irina Tirdea <irina.tirdea@xxxxxxxxx>
---
.../bindings/input/touchscreen/goodix.txt | 5 ++
drivers/input/touchscreen/goodix.c | 100 +++++++++++++++++++++
2 files changed, 105 insertions(+)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 8ba98ee..7137881 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -12,6 +12,8 @@ Required properties:
- reg : I2C address of the chip. Should be 0x5d or 0x14
- interrupt-parent : Interrupt controller to which the chip is connected
- interrupts : Interrupt to which the chip is connected
+ - irq-gpio : GPIO pin used for IRQ
+ - reset-gpio : GPIO pin used for reset
Example:
@@ -23,6 +25,9 @@ Example:
reg = <0x5d>;
interrupt-parent = <&gpio>;
interrupts = <0 0>;
+
+ irq-gpio = <&gpio1 0 0>;
+ reset-gpio = <&gpio1 1 0>;
};
/* ... */
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 7cd3780..c345eb7 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -24,6 +24,7 @@
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/acpi.h>
+#include <linux/gpio.h>
#include <linux/of.h>
#include <asm/unaligned.h>
@@ -34,8 +35,13 @@ struct goodix_ts_data {
int abs_y_max;
unsigned int max_touch_num;
unsigned int int_trigger_type;
+ struct gpio_desc *gpiod_int;
+ struct gpio_desc *gpiod_rst;
};
+#define GOODIX_GPIO_INT_NAME "irq"
+#define GOODIX_GPIO_RST_NAME "reset"
+
#define GOODIX_MAX_HEIGHT 4096
#define GOODIX_MAX_WIDTH 4096
#define GOODIX_INT_TRIGGER 1
@@ -186,6 +192,89 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+ int ret;
+
+ ret = gpiod_direction_output(ts->gpiod_int, 0);
+ if (ret)
+ return ret;
+
+ return gpiod_direction_input(ts->gpiod_int);
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+ int ret;
+
+ /* begin select I2C slave addr */
+ ret = gpiod_direction_output(ts->gpiod_rst, 0);
+ if (ret)
+ return ret;
+ msleep(20); /* T2: > 10ms */
+ /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+ ret = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+ if (ret)
+ return ret;
+ usleep_range(100, 2000); /* T3: > 100us */
+ ret = gpiod_direction_output(ts->gpiod_rst, 1);
+ if (ret)
+ return ret;
+ usleep_range(6000, 10000); /* T4: > 5ms */
+ /* end select I2C slave addr */
+ ret = gpiod_direction_input(ts->gpiod_rst);
+ if (ret)
+ return ret;
+ ret = goodix_int_sync(ts);
+ if (ret)
+ return ret;
+ msleep(50); /* T5: 50ms */
+ return 0;
+}
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts)
+{
+ struct device *dev;
+ struct gpio_desc *gpiod;
+ int ret;
+
+ if (!ts->client)
+ return -EINVAL;
+ dev = &ts->client->dev;
+
+ /* Get interrupt GPIO pin number */
+ gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ ret = PTR_ERR(gpiod);
+ dev_err(dev, "Failed to get %s GPIO: %d\n",
+ GOODIX_GPIO_INT_NAME, ret);
+ return ret;
+ }
+ ts->gpiod_int = gpiod;
+
+ /* Get the reset line GPIO pin number */
+ gpiod = devm_gpiod_get(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+ if (IS_ERR(gpiod)) {
+ ret = PTR_ERR(gpiod);
+ dev_err(dev, "Failed to get %s GPIO: %d\n",
+ GOODIX_GPIO_RST_NAME, ret);
+ return ret;
+ }
+ ts->gpiod_rst = gpiod;
+
+ return 0;
+}
+
/**
* goodix_read_config - Read the embedded configuration of the panel
*
@@ -365,6 +454,17 @@ static int goodix_ts_probe(struct i2c_client *client,
return error;
}
+ error = goodix_get_gpio_config(ts);
+ if (error)
+ return error;
+
+ /* reset the controller */
+ error = goodix_reset(ts);
+ if (error) {
+ dev_err(&client->dev, "Controller reset failed.\n");
+ return error;
+ }
+
goodix_read_config(ts);
error = goodix_request_input_dev(ts, version_info, id_info);
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
