On Tue, Jul 29, 2014 at 02:50:48PM +0100, Murphy, Dan wrote: > Mark > > Thanks for the feedback > > On 07/29/2014 04:37 AM, Mark Rutland wrote: > > On Mon, Jul 28, 2014 at 05:53:23PM +0100, Dan Murphy wrote: > >> Add the TI drv260x haptics/vibrator driver. > >> This device uses the input force feedback > >> to produce a wave form to driver an > >> ERM or LRA actuator device. > >> > >> The initial driver supports the devices > >> real time playback mode. But the device > >> has additional wave patterns in ROM. > >> > >> This functionality will be added in > >> future patchsets. > >> > >> Product data sheet is located here: > >> http://www.ti.com/product/drv2605 > >> > >> Signed-off-by: Dan Murphy <dmurphy@xxxxxx> > >> --- > >> > >> v2 - Fixed binding doc and patch headline - https://patchwork.kernel.org/patch/4619641/ > >> > >> .../devicetree/bindings/input/ti,drv260x.txt | 44 ++ > >> drivers/input/misc/Kconfig | 9 + > >> drivers/input/misc/Makefile | 1 + > >> drivers/input/misc/drv260x.c | 537 ++++++++++++++++++++ > >> include/dt-bindings/input/ti-drv260x.h | 30 ++ > >> include/linux/input/drv260x.h | 181 +++++++ > >> 6 files changed, 802 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/input/ti,drv260x.txt > >> create mode 100644 drivers/input/misc/drv260x.c > >> create mode 100644 include/dt-bindings/input/ti-drv260x.h > >> create mode 100644 include/linux/input/drv260x.h > >> > >> diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt > >> new file mode 100644 > >> index 0000000..930429b > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt > >> @@ -0,0 +1,44 @@ > >> +Texas Instruments - drv260x Haptics driver family > >> + > >> +The drv260x family serial control bus communicates through I2C protocols > >> + > >> +Required properties: > >> + - compatible - One of: > >> + "ti,drv2604" - DRV2604 > >> + "ti,drv2605" - DRV2605 > >> + "ti,drv2605l" - DRV2605L > >> + - reg - I2C slave address > >> + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) > >> + DRV260X_RTP_MODE - Real time playback mode > >> + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) > >> + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) > > > > What exactly are these, and why does the kernel not decide? > > The LRA and ERM are vibrator types. These are specific to the product and the kernel cannot decide. > The kernel driver needs to be told what type of vibrator is connected. The driver then > sets the voltages and other settings to drive the vibrator type safely. All vibrators are dumb and do not > have IDs identifying themselves so there is no self discovery here. I see. That makes sense, thanks for the description. It might make more sense to call this "vibrator-type", rather than "mode", but otherwise this should be ok. In the past I've asked for strings rather than magic numbers, but I'll leave that choice to you. > RTP is not a vibrator type but just a mode you can place the device into. I can probably remove that > and have the user space or driver take care of that setting. Ok, that sounds good to me. > > > > >> + - library_sel - Library to use at power up (defined in include/dt-bindings/input/ti-drv260x.h) > > > > Please s/_/-/ in all property names. > > > >> + DRV260X_LIB_A - Pre-programmed Library > >> + DRV260X_LIB_B - Pre-programmed Library > >> + DRV260X_LIB_C - Pre-programmed Library > >> + DRV260X_LIB_D - Pre-programmed Library > >> + DRV260X_LIB_E - Pre-programmed Library > >> + DRV260X_LIB_F - Pre-programmed Library > > > > What exactly are these, and why does the kernel not decide? > > > >> + > >> +Optional properties: > >> + - enable-gpio - gpio pin to enable/disable the device. > >> + - vib_rated_voltage - The rated voltage of the actuator. If this is not > >> + set then the value will be defaulted to 0x90 in the > >> + driver. > > > > What units is this in? > > Good catch I was thinking this when I was writing the documentation but forgot to add > it. I will fix the formatting here and below as well. Cheers. Mark. -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
