On Fri, Aug 31, 2012 at 06:53:53PM -0400, Forest Bond wrote:
> Hi,
>
> On Fri, Aug 31, 2012 at 04:04:58PM -0400, Alan Stern wrote:
> > On Fri, 31 Aug 2012, Dmitry Torokhov wrote:
> >
> > > > > + /* Send a "check active" packet. The response will be read
> > > > > + * later and ignored. */
> > > > > + ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
> > > > > + 0,
> > > > > + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
> > > > > + 0, 0, "\x0A\x01A", 0,
> > > >
> > > > You probably can't send data from the .const section (as well as off the
> > > > stack) -- they can be DMA'ed and there'll be issues with cache consistency on
> > > > non-x86 arches. You should allocate the data with kmalloc().
> > > > Although, on the second thought, maybe I'm wrong in this case... not really
> > > > sure about sending -- receiving (to the .data section) could certainly be harmful...
> > >
> > > Hmm, do we actually send anything here? The "size" passed to
> > > usb_control_msg() is 0 so I don't think we use that data at all...
> >
> > Good point. Perhaps the 0 is a typo, in which case data does get sent
> > and the buffer must be kmalloc'ed. If the 0 is correct then the buffer
> > should be NULL, not "\x0A\x01A" (and what's the purpose of the leading
> > '0' in the second byte?).
> >
> > In addition, although the bRequestType specifies USB_DIR_OUT, the pipe
> > value is usb_rcvctrlpipe. Is this transfer meant to be IN or OUT?
>
> Thanks again to all for the review. My theory for why the previous patch worked
> in spite of its wrongness is that the device actually switches modes when it
> receives a control message with USB_TYPE_VENDOR even though the documentation
> suggests an actual diagnostic packet must be received.
>
> Does this (untested) patch look more reasonable?
Yes, but we still need it tested, please.
>
>
> diff --git a/drivers/input/touchscreen/usbtouchscreen.c b/drivers/input/touchscreen/usbtouchscreen.c
> index e32709e..64b4b17 100644
> --- a/drivers/input/touchscreen/usbtouchscreen.c
> +++ b/drivers/input/touchscreen/usbtouchscreen.c
> @@ -304,6 +304,41 @@ static int e2i_read_data(struct usbtouch_usb *dev, unsigned char *pkt)
> #define EGALAX_PKT_TYPE_REPT 0x80
> #define EGALAX_PKT_TYPE_DIAG 0x0A
>
> +static int egalax_init(struct usbtouch_usb *usbtouch)
> +{
> + int ret, i;
> + unsigned char *buf;
> + struct usb_device *udev = interface_to_usbdev(usbtouch->interface);
> +
> + /* An eGalax diagnostic packet kicks the device into using the right
> + * protocol. We send a "check active" packet. The response will be
> + * read later and ignored.
> + */
> +
> + buf = kmalloc(3, GFP_KERNEL);
> + buf[0] = EGALAX_PKT_TYPE_DIAG;
> + buf[1] = 1; /* length */
> + buf[2] = 'A'; /* command - check active */
> +
> + for (i = 0; i < 3; i++) {
> + ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
> + 0,
> + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
> + 0, 0, buf, 3,
> + USB_CTRL_SET_TIMEOUT);
> + if (ret >= 0) {
> + ret = 0;
> + break;
> + }
> + if (ret != -EPIPE)
> + break;
> + }
> +
> + kfree(buf);
> +
> + return ret;
> +}
> +
> static int egalax_read_data(struct usbtouch_usb *dev, unsigned char *pkt)
> {
> if ((pkt[0] & EGALAX_PKT_TYPE_MASK) != EGALAX_PKT_TYPE_REPT)
> @@ -1056,6 +1091,7 @@ static struct usbtouch_device_info usbtouch_dev_info[] = {
> .process_pkt = usbtouch_process_multi,
> .get_pkt_len = egalax_get_pkt_len,
> .read_data = egalax_read_data,
> + .init = egalax_init,
> },
> #endif
>
>
> Thanks,
> Forest
> --
> Forest Bond
> http://www.alittletooquiet.net
> http://www.rapidrollout.com
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
