> > +static int da906x_set_voltage(struct regulator_dev *rdev,
> > + int min_uV, int max_uV, unsigned *selector)
> > +{
> > + struct da906x_regulator *regl = rdev_get_drvdata(rdev);
> > + const struct field *fvol = ®l->info->voltage;
> > + int ret;
> > + unsigned val;
> > +
> > + val = regulator_map_voltage_linear(rdev, min_uV, max_uV);
> > + if (val < 0)
> > + return -EINVAL;
> > +
> > + val = (val + fvol->offset) << fvol->shift;
> > + ret = da906x_reg_update(regl->hw, fvol->addr, fvol->mask, val);
> > + if (ret >= 0)
> > + *selector = val;
> > +
> > + return ret;
> > +}
>
> This is just set_voltage_sel_regmap().
Because, for some regulators, this is required: val += fvol->offset,
I was only able to reduce it to the following form.
+static int da9063_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV, unsigned *selector)
+{
+ struct da9063_regulator *regl = rdev_get_drvdata(rdev);
+ const struct field *fvol = ®l->info->voltage;
+ int ret;
+ unsigned val;
+
+ val = regulator_map_voltage_linear(rdev, min_uV, max_uV);
+ if (val < 0)
+ return -EINVAL;
+
+ val += fvol->offset;
+
+ ret = regulator_set_voltage_sel_regmap(rdev, val);
+ if (ret >= 0)
+ *selector = val;
+
+ return ret;
+}
> > +static int da906x_enable(struct regulator_dev *rdev)
> > +{
> > + struct da906x_regulator *regl = rdev_get_drvdata(rdev);
> > + int ret;
> > +
> > + if (regl->info->suspend.mask) {
> > + /* Make sure to exit from suspend mode on enable */
> > + ret = da906x_reg_clear_bits(regl->hw, regl->info->suspend.addr,
> > + regl->info->suspend.mask);
> > + if (ret < 0)
> > + return ret;
> > +
> > + /* BUCKs need mode update after wake-up from suspend state. */
> > + ret = da906x_update_mode_internal(regl, SYS_STATE_NORMAL);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + return regulator_enable_regmap(rdev);
>
> If suspend_mask is optional the regulators using it should just use the
> standard operation.
I guess, you meant here to call regulator_enable_regmap() directly for
regulators NOT using suspend.mask. Then, I will do it.
> > +/* Regulator event handlers */
> > +irqreturn_t da906x_ldo_lim_event(int irq, void *data)
>
> By "event handler" you mean "interrupt"
Yes. I think, I will update the comment line.
> > + bits = da906x_reg_read(hw, DA906X_REG_STATUS_D);
> > + if (bits < 0)
> > + return IRQ_HANDLED;
>
> If you fail to detect an interrupt you report that you handled one...?
For me there is no sensible return value for this case.
However, I consider changing the reaction on read failure by reporting event
for all regulators, that might cause this interrupt:
+ bits = da9063_reg_read(hw, DA9063_REG_STATUS_D);
+ if (bits < 0)
+ bits = ~0;
I will update the driver according to your remaining comments.
Thank you for your comments,
Krystian
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
