This patch adds the dts files for the reference machine of LPC32xx: * arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx * arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250 Signed-off-by: Roland Stigge <stigge@xxxxxxxxx> --- arch/arm/boot/dts/lpc32xx.dtsi | 303 +++++++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/phy3250.dts | 115 +++++++++++++++ 2 files changed, 418 insertions(+) --- /dev/null +++ linux-2.6/arch/arm/boot/dts/lpc32xx.dtsi @@ -0,0 +1,303 @@ +/* + * NXP LPC32xx SoC + * + * Copyright 2012 Roland Stigge <stigge@xxxxxxxxx> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "nxp,lpc32xx"; + + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + ahb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + slc: flash@20020000 { + compatible = "nxp,nand-slc"; + reg = <0x20020000 0x1000>; + status = "disable"; + }; + + mlc: flash@200B0000 { + compatible = "nxp,nand-mlc"; + reg = <0x200B0000 0x1000>; + status = "disable"; + }; + + dma@31000000 { + compatible = "arm,pl080", "arm,primecell"; + reg = <0x31000000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x1c 0>; + }; + + /* + * Enable either ohci or usbd (gadget)! + */ + ohci@31020000 { + compatible = "nxp,ohci-nxp", "usb-ohci"; + reg = <0x31020000 0x300>; + interrupt-parent = <&mic>; + interrupts = <0x3b 0>; + status = "disable"; + }; + + usbd@31020000 { + compatible = "nxp,lpc32xx-udc"; + reg = <0x31020000 0x300>; + interrupt-parent = <&mic>; + interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; + status = "disable"; + }; + + clcd@31040000 { + compatible = "arm,pl110", "arm,primecell"; + reg = <0x31040000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x0e 0>; + status = "disable"; + }; + + mac: ethernet@31060000 { + compatible = "nxp,lpc-eth"; + reg = <0x31060000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x1d 0>; + }; + + apb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + ssp0: ssp@20084000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x20084000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x14 0>; + }; + + spi1: spi@20088000 { + compatible = "nxp,spi"; + reg = <0x20088000 0x1000>; + }; + + ssp1: ssp@2008c000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x2008c000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x15 0>; + }; + + spi2: spi@20090000 { + compatible = "nxp,spi"; + reg = <0x20090000 0x1000>; + }; + + i2s0: i2s@20094000 { + compatible = "nxp,i2s"; + reg = <0x20094000 0x1000>; + }; + + sd@20098000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x20098000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x0f 0>, <0x0d 0>; + }; + + i2s1: i2s@2009C000 { + compatible = "nxp,i2s"; + reg = <0x2009C000 0x1000>; + }; + + uart3: serial@40080000 { + compatible = "nxp,serial"; + reg = <0x40080000 0x1000>; + }; + + uart4: serial@40088000 { + compatible = "nxp,serial"; + reg = <0x40088000 0x1000>; + }; + + uart5: serial@40090000 { + compatible = "nxp,serial"; + reg = <0x40090000 0x1000>; + }; + + uart6: serial@40098000 { + compatible = "nxp,serial"; + reg = <0x40098000 0x1000>; + }; + + i2c1: i2c@400A0000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400A0000 0x100>; + interrupt-parent = <&mic>; + interrupts = <0x33 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + + i2c2: i2c@400A8000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400A8000 0x100>; + interrupt-parent = <&mic>; + interrupts = <0x32 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + + i2cusb: i2c@31020300 { + compatible = "nxp,pnx-i2c"; + reg = <0x31020300 0x100>; + interrupt-parent = <&mic>; + interrupts = <0x3f 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + }; + + fab { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + /* + * MIC Interrupt controller includes: + * MIC @40008000 + * SIC1 @4000C000 + * SIC2 @40010000 + */ + mic: interrupt-controller@40008000 { + compatible = "nxp,lpc32xx-mic"; + interrupt-controller; + interrupt-parent; + reg = <0x40008000 0xC000>; + #interrupt-cells = <2>; + }; + + uart1: serial@40014000 { + compatible = "nxp,serial"; + reg = <0x40014000 0x1000>; + }; + + uart2: serial@40018000 { + compatible = "nxp,serial"; + reg = <0x40018000 0x1000>; + }; + + uart7: serial@4001C000 { + compatible = "nxp,serial"; + reg = <0x4001C000 0x1000>; + }; + + rtc@40024000 { + compatible = "nxp,lpc32xx-rtc"; + reg = <0x40024000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x34 0>; + }; + + gpio: gpio@40028000 { + compatible = "nxp,lpc32xx-gpio"; + reg = <0x40028000 0x1000>; + /* create a private address space for enumeration */ + #address-cells = <1>; + #size-cells = <0>; + + gpio_p0: gpio-bank@0 { + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + }; + + gpio_p1: gpio-bank@1 { + gpio-controller; + #gpio-cells = <2>; + reg = <1>; + }; + + gpio_p2: gpio-bank@2 { + gpio-controller; + #gpio-cells = <2>; + reg = <2>; + }; + + gpio_p3: gpio-bank@3 { + gpio-controller; + #gpio-cells = <2>; + reg = <3>; + }; + + gpi_p3: gpio-bank@4 { + gpio-controller; + #gpio-cells = <2>; + reg = <4>; + }; + + gpo_p3: gpio-bank@5 { + gpio-controller; + #gpio-cells = <2>; + reg = <5>; + }; + }; + + watchdog@4003C000 { + compatible = "nxp,pnx4008-wdt"; + reg = <0x4003C000 0x1000>; + }; + + /* + * TSC vs. ADC: Since those two share the same + * hardware, you need to choose from one of the + * following two and do 'status = "okay";" for one of + * them + */ + + adc@40048000 { + compatible = "nxp,lpc32xx-adc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x27 0>; + status = "disable"; + }; + + tsc@40048000 { + compatible = "nxp,lpc32xx-tsc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <0x27 0>; + status = "disable"; + }; + + key@40050000 { + compatible = "nxp,key"; + reg = <0x40050000 0x1000>; + }; + + }; + }; +}; --- /dev/null +++ linux-2.6/arch/arm/boot/dts/phy3250.dts @@ -0,0 +1,115 @@ +/* + * PHYTEC phyCORE-LPC3250 board + * + * Copyright 2012 Roland Stigge <stigge@xxxxxxxxx> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "lpc32xx.dtsi" + +/ { + model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; + compatible = "phytec,phy3250", "nxp,lpc32xx"; + #address-cells = <1>; + #size-cells = <1>; + + memory { + device_type = "memory"; + reg = <0 0x4000000>; + }; + + ahb { + mac: ethernet@31060000 { + phy-mode = "rmii"; + use-iram; + }; + + /* Here, choose from: ohci, usbd */ + ohci@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; + +/* + usbd@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; +*/ + + clcd@31040000 { + status = "okay"; + }; + + apb { + i2c1: i2c@400A0000 { + clock-frequency = <0x186a0>; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + uda1380: uda1380@18 { + compatible = "nxp,uda1380"; + reg = <0x18>; + power-gpio = <&gpio 0x59 0>; + reset-gpio = <&gpio 0x51 0>; + dac-clk = "wspll"; + }; + }; + + i2c2: i2c@400A8000 { + clock-frequency = <0x186a0>; + }; + + i2cusb: i2c@31020300 { + clock-frequency = <0x186a0>; + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + }; + + ssp0: ssp@20084000 { + eeprom: at25@0 { + compatible = "atmel,at25"; + }; + }; + }; + + fab { + tsc@40048000 { + status = "okay"; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpo_p3 1 1>; /* GPO_P3 1, GPIO 80, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpo_p3 14 1>; /* GPO_P3 14, GPIO 93, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; + + chosen { + bootargs = "console=ttyS0,115200n81 root=/dev/ram0"; + }; +}; -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
