Hi Dmitry,
Please ignore this patch. Just now I sent a new PATCHv2.
Thanks & Regards,
Naveen
> -----Original Message-----
> From: Naveen Kumar GADDIPATI
> Sent: Thursday, September 09, 2010 5:06 PM
> To: Dmitry Torokhov
> Cc: 'Trilok Soni'; linux-input@xxxxxxxxxxxxxxx;
> STEricsson_nomadik_linux
> Subject: [Patch v2] input:rohm based bu21013 touch panel controller
> driver support
>
> Hi Dmitry,
>
> From: Naveen Kumar Gaddipati <naveen.gaddipati@xxxxxxxxxxxxxx>
>
> Added the ROHM based bu21013 capacitive touch panel controller
> driver support with i2c interface.
>
> Acked-by: Linus Walleij <linus.walleij@xxxxxxxxxxxxxx>
> Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@xxxxxxxxxxxxxx>
> ---
> Modifications in v2:
> --Updated with the Dmitry comments on Patch v1
> --Updated with the Trilok comments on Patch v1
>
>
> drivers/input/touchscreen/Kconfig | 12 +
> drivers/input/touchscreen/Makefile | 1 +
> drivers/input/touchscreen/bu21013_ts.c | 770
> ++++++++++++++++++++++++++++++++
> include/linux/input/bu21013.h | 44 ++
> 4 files changed, 827 insertions(+), 0 deletions(-)
> create mode 100644 drivers/input/touchscreen/bu21013_ts.c
> create mode 100644 include/linux/input/bu21013.h
>
> diff --git a/drivers/input/touchscreen/Kconfig
> b/drivers/input/touchscreen/Kconfig
> index 0069d97..2380533 100644
> --- a/drivers/input/touchscreen/Kconfig
> +++ b/drivers/input/touchscreen/Kconfig
> @@ -98,6 +98,18 @@ config TOUCHSCREEN_BITSY
> To compile this driver as a module, choose M here: the
> module will be called h3600_ts_input.
>
> +config TOUCHSCREEN_BU21013
> + tristate "BU21013 based touch panel controllers"
> + depends on I2C
> + help
> + Say Y here if you have a bu21013 touchscreen connected to
> + your system.
> +
> + If unsure, say N.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called bu21013_ts.
> +
> config TOUCHSCREEN_CY8CTMG110
> tristate "cy8ctmg110 touchscreen"
> depends on I2C
> diff --git a/drivers/input/touchscreen/Makefile
> b/drivers/input/touchscreen/Makefile
> index 28217e1..a0a2021 100644
> --- a/drivers/input/touchscreen/Makefile
> +++ b/drivers/input/touchscreen/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI) += ad7879-
> spi.o
> obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
> obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o
> obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
> +obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
> obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
> obj-$(CONFIG_TOUCHSCREEN_DA9034) += da9034-ts.o
> obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
> diff --git a/drivers/input/touchscreen/bu21013_ts.c
> b/drivers/input/touchscreen/bu21013_ts.c
> new file mode 100644
> index 0000000..117d9c5
> --- /dev/null
> +++ b/drivers/input/touchscreen/bu21013_ts.c
> @@ -0,0 +1,770 @@
> +/*
> + * Copyright (C) ST-Ericsson SA 2010
> + * Author: Naveen Kumar G <naveen.gaddipati@xxxxxxxxxxxxxx> for ST-
> Ericsson
> + * License terms:GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/i2c.h>
> +#include <linux/workqueue.h>
> +#include <linux/input.h>
> +#include <linux/types.h>
> +#include <linux/timer.h>
> +#include <linux/input/bu21013.h>
> +#include <linux/slab.h>
> +
> +#define PEN_DOWN_INTR 0
> +#define PEN_UP_INTR 1
> +#define RESET_DELAY 30
> +#define POLLING_DELAY 100
> +#define MAX_TOOL_WIDTH 15
> +#define MAX_TOUCH_MAJOR 255
> +#define MAX_TOUCH_MINOR 15
> +#define MAX_PRESSURE 1
> +#define PENUP_TIMEOUT (2)
> +#define DELTA_MIN 16
> +#define MASK_BITS 0x03
> +#define SHIFT_8 8
> +#define SHIFT_2 2
> +#define LENGTH_OF_BUFFER 11
> +
> +#define BU21013_SENSORS_BTN_0_7_REG 0x70
> +#define BU21013_SENSORS_BTN_8_15_REG 0x71
> +#define BU21013_SENSORS_BTN_16_23_REG 0x72
> +#define BU21013_X1_POS_MSB_REG 0x73
> +#define BU21013_X1_POS_LSB_REG 0x74
> +#define BU21013_Y1_POS_MSB_REG 0x75
> +#define BU21013_Y1_POS_LSB_REG 0x76
> +#define BU21013_X2_POS_MSB_REG 0x77
> +#define BU21013_X2_POS_LSB_REG 0x78
> +#define BU21013_Y2_POS_MSB_REG 0x79
> +#define BU21013_Y2_POS_LSB_REG 0x7A
> +#define BU21013_INT_CLR_REG 0xE8
> +#define BU21013_INT_MODE_REG 0xE9
> +#define BU21013_GAIN_REG 0xEA
> +#define BU21013_OFFSET_MODE_REG 0xEB
> +#define BU21013_XY_EDGE_REG 0xEC
> +#define BU21013_RESET_REG 0xED
> +#define BU21013_CALIB_REG 0xEE
> +#define BU21013_DONE_REG 0xEF
> +#define BU21013_SENSOR_0_7_REG 0xF0
> +#define BU21013_SENSOR_8_15_REG 0xF1
> +#define BU21013_SENSOR_16_23_REG 0xF2
> +#define BU21013_POS_MODE1_REG 0xF3
> +#define BU21013_POS_MODE2_REG 0xF4
> +#define BU21013_CLK_MODE_REG 0xF5
> +#define BU21013_IDLE_REG 0xFA
> +#define BU21013_FILTER_REG 0xFB
> +#define BU21013_TH_ON_REG 0xFC
> +#define BU21013_TH_OFF_REG 0xFD
> +
> +#define BU21013_RESET_ENABLE 0x01
> +
> +#define BU21013_SENSORS_EN_0_7 0x3F
> +#define BU21013_SENSORS_EN_8_15 0xFC
> +#define BU21013_SENSORS_EN_16_23 0x1F
> +
> +#define BU21013_POS_MODE1_0 0x02
> +#define BU21013_POS_MODE1_1 0x04
> +#define BU21013_POS_MODE1_2 0x08
> +
> +#define BU21013_POS_MODE2_ZERO 0x01
> +#define BU21013_POS_MODE2_AVG1 0x02
> +#define BU21013_POS_MODE2_AVG2 0x04
> +#define BU21013_POS_MODE2_EN_XY 0x08
> +#define BU21013_POS_MODE2_EN_RAW 0x10
> +#define BU21013_POS_MODE2_MULTI 0x80
> +
> +#define BU21013_CLK_MODE_DIV 0x01
> +#define BU21013_CLK_MODE_EXT 0x02
> +#define BU21013_CLK_MODE_CALIB 0x80
> +
> +#define BU21013_IDLET_0 0x01
> +#define BU21013_IDLET_1 0x02
> +#define BU21013_IDLET_2 0x04
> +#define BU21013_IDLET_3 0x08
> +#define BU21013_IDLE_INTERMIT_EN 0x10
> +
> +#define BU21013_DELTA_0_6 0x7F
> +#define BU21013_FILTER_EN 0x80
> +
> +#define BU21013_INT_MODE_LEVEL 0x00
> +#define BU21013_INT_MODE_EDGE 0x01
> +
> +#define BU21013_GAIN_0 0x01
> +#define BU21013_GAIN_1 0x02
> +#define BU21013_GAIN_2 0x04
> +
> +#define BU21013_OFFSET_MODE_DEFAULT 0x00
> +#define BU21013_OFFSET_MODE_MOVE 0x01
> +#define BU21013_OFFSET_MODE_DISABLE 0x02
> +
> +#define BU21013_TH_ON_0 0x01
> +#define BU21013_TH_ON_1 0x02
> +#define BU21013_TH_ON_2 0x04
> +#define BU21013_TH_ON_3 0x08
> +#define BU21013_TH_ON_4 0x10
> +#define BU21013_TH_ON_5 0x20
> +#define BU21013_TH_ON_6 0x40
> +#define BU21013_TH_ON_7 0x80
> +#define BU21013_TH_ON_MAX 0xFF
> +
> +#define BU21013_TH_OFF_0 0x01
> +#define BU21013_TH_OFF_1 0x02
> +#define BU21013_TH_OFF_2 0x04
> +#define BU21013_TH_OFF_3 0x08
> +#define BU21013_TH_OFF_4 0x10
> +#define BU21013_TH_OFF_5 0x20
> +#define BU21013_TH_OFF_6 0x40
> +#define BU21013_TH_OFF_7 0x80
> +#define BU21013_TH_OFF_MAX 0xFF
> +
> +#define BU21013_X_EDGE_0 0x01
> +#define BU21013_X_EDGE_1 0x02
> +#define BU21013_X_EDGE_2 0x04
> +#define BU21013_X_EDGE_3 0x08
> +#define BU21013_Y_EDGE_0 0x10
> +#define BU21013_Y_EDGE_1 0x20
> +#define BU21013_Y_EDGE_2 0x40
> +#define BU21013_Y_EDGE_3 0x80
> +
> +#define BU21013_DONE 0x01
> +#define BU21013_NUMBER_OF_X_SENSORS (6)
> +#define BU21013_NUMBER_OF_Y_SENSORS (11)
> +
> +#define DRIVER_TP "bu21013_tp"
> +
> +/**
> + * struct bu21013_ts_data - touch panel data structure
> + * @client: pointer to the i2c client
> + * @chip: pointer to the touch panel controller
> + * @in_dev: pointer to the input device structure
> + * @wait: variable to wait_queue_head_t structure
> + * @intr_pin: interrupt pin value
> + * @touch_stopped: touch stop flag
> + * @x_pos: x position for two co-ordinates
> + * @y_pos: y position for two co-ordinates
> + * @previous_press_reported: last reported flag
> + *
> + * Touch panel device data structure
> + */
> +struct bu21013_ts_data {
> + struct i2c_client *client;
> + struct bu21013_platform_device *chip;
> + struct input_dev *in_dev;
> + wait_queue_head_t wait;
> + bool touch_stopped;
> + unsigned int intr_pin;
> + signed short x_pos[2];
> + signed short y_pos[2];
> + bool previous_press_reported;
> +};
> +
> +/**
> + * bu21013_report_pen_down() - reports the pen down event
> + * @data:bu21013_ts_data structure pointer
> + * @count:touch count
> + *
> + * This function used to report the pen down interrupt to
> + * input subsystem and returns none
> + */
> +static void bu21013_report_pen_down(struct bu21013_ts_data *data, int
> count)
> +{
> + int i;
> +
> + input_report_abs(data->in_dev, ABS_X, data->x_pos[0]);
> + input_report_abs(data->in_dev, ABS_Y, data->y_pos[0]);
> + input_report_key(data->in_dev, BTN_TOUCH, count);
> +
> + if (data->chip->multi_touch) {
> + for (i = 0; i < count; i++) {
> + input_report_abs(data->in_dev, ABS_MT_POSITION_X,
> + data->x_pos[i]);
> + input_report_abs(data->in_dev, ABS_MT_POSITION_Y,
> + data->y_pos[i]);
> + input_mt_sync(data->in_dev);
> + }
> + }
> + input_sync(data->in_dev);
> + data->previous_press_reported = count;
> +}
> +/**
> + * bu21013_report_pen_up() - reports the pen up event
> + * @data:bu21013_ts_data structure pointer
> + *
> + * This function used to report the pen up interrupt
> + * to input subsystem and returns none
> + */
> +static void bu21013_report_pen_up(struct bu21013_ts_data *data)
> +{
> + input_report_key(data->in_dev, BTN_TOUCH, 0);
> + if (data->chip->multi_touch) {
> + input_report_key(data->in_dev, BTN_2, 0);
> + input_mt_sync(data->in_dev);
> + }
> + input_sync(data->in_dev);
> + data->previous_press_reported = 0;
> +}
> +/**
> + * bu21013_touch_calc() - calculates the co-ordinates delta
> + * @data: bu21013_ts_data structure pointer
> + * @x: x position
> + * @y: y position
> + * @count: touch count
> + *
> + * This function calculates the exact co-ordinates with respect to
> + * display resolution and returns none
> + */
> +static void bu21013_touch_calc
> + (struct bu21013_ts_data *data, int x, int y, int count)
> +{
> + data->x_pos[count] = x;
> + data->y_pos[count] = y;
> + if (data->chip->x_flip)
> + data->x_pos[count] =
> + data->chip->touch_x_max - data->x_pos[count];
> + if (data->chip->y_flip)
> + data->y_pos[count] =
> + data->chip->touch_y_max - data->y_pos[count];
> +}
> +/**
> + * bu21013_verify_delta() - verify the co-ordinates delta
> + * @x1: x1 position
> + * @y1: y1 position
> + * @x2: x2 position
> + * @y2: y2 position
> + *
> + * This function verifies the delta of the
> + * co-ordinates and returns boolean.
> + */
> +static bool bu21013_verify_delta(int x1, int y1, int x2, int y2)
> +{
> + int delta_x, delta_y;
> +
> + if ((x1 != 0) && (y1 != 0)) {
> + delta_x = x2 - x1;
> + if (x1 > x2)
> + delta_x = x1 - x2;
> + delta_y = y2 - y1;
> + if (y1 > y2)
> + delta_y = y1 - y2;
> + if ((delta_x < DELTA_MIN) || (delta_y < DELTA_MIN))
> + return false;
> + }
> + return true;
> +}
> +
> +/**
> + * bu21013_do_touch_report(): Get the touch co-ordinates
> + * @data:bu21013_ts_data structure pointer
> + *
> + * Get the touch co-ordinates from touch sensor registers and writes
> + * into device structure and returns integer.
> + */
> +static int bu21013_do_touch_report(struct bu21013_ts_data *data)
> +{
> + u8 buf[LENGTH_OF_BUFFER];
> + int finger1_valid = 0;
> + int finger2_valid = 0;
> + unsigned int finger1_pos_x;
> + unsigned int finger1_pos_y;
> + unsigned int finger2_pos_x = 0;
> + unsigned int finger2_pos_y = 0;
> + int number_of_active_x_sensors;
> + int number_of_active_y_sensors;
> + int total_number_of_active_sensors;
> + int finger_down_count = 0;
> + int ret = 0;
> +
> + if (data == NULL)
> + return -EINVAL;
> +
> + ret = i2c_smbus_read_i2c_block_data(data->client,
> + BU21013_SENSORS_BTN_0_7_REG,
> + LENGTH_OF_BUFFER, buf);
> + if (ret < LENGTH_OF_BUFFER)
> + return -EINVAL;
> +
> + number_of_active_x_sensors = hweight32(buf[0] &
> + BU21013_SENSORS_EN_0_7);
> + number_of_active_y_sensors = hweight32(
> + ((buf[1] & BU21013_SENSORS_EN_8_15) |
> + ((buf[2] & BU21013_SENSORS_EN_16_23) << SHIFT_8)) >>
> SHIFT_2);
> + if (((number_of_active_x_sensors != 0) &&
> + (number_of_active_y_sensors == 0)) ||
> + ((number_of_active_x_sensors == 0) &&
> + (number_of_active_y_sensors != 0)))
> + return 0;
> +
> + total_number_of_active_sensors =
> + number_of_active_x_sensors + number_of_active_y_sensors;
> +
> + finger1_pos_x = buf[3] << SHIFT_2 | (buf[4] & MASK_BITS);
> + finger1_pos_y = buf[5] << SHIFT_2 | (buf[6] & MASK_BITS);
> +
> + if (data->chip->multi_touch) {
> + finger2_pos_x = buf[7] << SHIFT_2 | (buf[8] & MASK_BITS);
> + finger2_pos_y = buf[9] << SHIFT_2 | (buf[10] & MASK_BITS);
> + }
> +
> + if (total_number_of_active_sensors) {
> + if ((finger2_pos_x != 0) && (finger2_pos_y != 0)) {
> + if ((finger1_pos_x == 0) || (finger1_pos_y == 0))
> + return 0;
> + ret = bu21013_verify_delta(finger1_pos_x,
> + finger1_pos_y, finger2_pos_x, finger2_pos_y);
> + if (!ret)
> + total_number_of_active_sensors = 0;
> + }
> + }
> +
> + if (total_number_of_active_sensors) {
> + finger1_valid = 1;
> + if ((finger1_pos_x == 0) || (finger1_pos_y == 0) ||
> + (finger1_pos_x >= data->chip->touch_x_max) ||
> + (finger1_pos_y >= data->chip->touch_y_max))
> + finger1_valid = 0;
> + finger2_valid = 1;
> + if ((finger2_pos_x == 0) || (finger2_pos_y == 0) ||
> + (finger2_pos_x >= data->chip->touch_x_max) ||
> + (finger2_pos_y >= data->chip->touch_y_max))
> + finger2_valid = 0;
> + if ((finger1_valid == 0) && (finger2_valid == 0))
> + return 0;
> + if (finger1_valid) {
> + bu21013_touch_calc(data, finger1_pos_x,
> + finger1_pos_y, finger_down_count);
> + finger_down_count++;
> + }
> + if (finger2_valid) {
> + bu21013_touch_calc(data, finger2_pos_x,
> + finger2_pos_y, finger_down_count);
> + finger_down_count++;
> + }
> + }
> +
> + if (finger_down_count > 0)
> + bu21013_report_pen_down(data, finger_down_count);
> + else {
> + if (data->previous_press_reported)
> + bu21013_report_pen_up(data);
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * bu21013_gpio_irq() - gpio thread function for touch interrupt
> + * @irq: irq value
> + * @device_data:void pointer
> + *
> + * This gpio thread function for touch interrupt
> + * and returns irqreturn_t.
> + */
> +static irqreturn_t bu21013_gpio_irq(int irq, void *device_data)
> +{
> + struct bu21013_ts_data *data = device_data;
> + struct i2c_client *i2c = data->client;
> + int retval;
> +
> + do {
> + retval = bu21013_do_touch_report(data);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "bu21013_do_touch_report
> failed\n");
> + return IRQ_NONE;
> + }
> +
> + data->intr_pin = data->chip->irq_read_val();
> + if (data->intr_pin == PEN_DOWN_INTR)
> + wait_event_timeout(data->wait, data->touch_stopped,
> + msecs_to_jiffies(10));
> + } while (!data->intr_pin && !data->touch_stopped);
> +
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * bu21013_init_chip() - power on sequence for the bu21013 controller
> + * @data: device structure pointer
> + *
> + * This function is used to power on
> + * the bu21013 controller and returns integer.
> + */
> +static int bu21013_init_chip(struct bu21013_ts_data *data)
> +{
> + int retval;
> + struct i2c_client *i2c = data->client;
> +
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_RESET_REG,
> + BU21013_RESET_ENABLE);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_RESET reg write failed\n");
> + goto err;
> + }
> + msleep(RESET_DELAY);
> +
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_0_7_REG,
> + BU21013_SENSORS_EN_0_7);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write
> failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_8_15_REG,
> + BU21013_SENSORS_EN_8_15);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write
> failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_16_23_REG,
> + BU21013_SENSORS_EN_16_23);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write
> failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE1_REG,
> + (BU21013_POS_MODE1_0 | BU21013_POS_MODE1_1));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n");
> + goto err;
> + }
> + if (data->chip->multi_touch)
> + retval = i2c_smbus_write_byte_data(i2c,
> BU21013_POS_MODE2_REG,
> + (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
> + BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW |
> + BU21013_POS_MODE2_MULTI));
> + else
> + retval = i2c_smbus_write_byte_data(i2c,
> BU21013_POS_MODE2_REG,
> + (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
> + BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n");
> + goto err;
> + }
> + if (data->chip->ext_clk)
> + retval = i2c_smbus_write_byte_data(i2c,
> BU21013_CLK_MODE_REG,
> + (BU21013_CLK_MODE_EXT | BU21013_CLK_MODE_CALIB));
> + else
> + retval = i2c_smbus_write_byte_data(i2c,
> BU21013_CLK_MODE_REG,
> + (BU21013_CLK_MODE_DIV | BU21013_CLK_MODE_CALIB));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_IDLE_REG,
> + (BU21013_IDLET_0 | BU21013_IDLE_INTERMIT_EN));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_INT_MODE_REG,
> + BU21013_INT_MODE_LEVEL);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_FILTER_REG,
> + (BU21013_DELTA_0_6 |
> + BU21013_FILTER_EN));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n");
> + goto err;
> + }
> +
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_ON_REG,
> + (BU21013_TH_ON_3 | BU21013_TH_ON_4));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_OFF_REG,
> + BU21013_TH_OFF_4);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_GAIN_REG,
> + (BU21013_GAIN_0 | BU21013_GAIN_1));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n");
> + goto err;
> + }
> +
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_OFFSET_MODE_REG,
> + BU21013_OFFSET_MODE_DEFAULT);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write
> failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_XY_EDGE_REG,
> + (BU21013_X_EDGE_0 | BU21013_X_EDGE_2 |
> + BU21013_Y_EDGE_1 | BU21013_Y_EDGE_3));
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n");
> + goto err;
> + }
> + retval = i2c_smbus_write_byte_data(i2c, BU21013_DONE_REG,
> + BU21013_DONE);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n");
> + goto err;
> + }
> +
> + data->x_pos[0] = 0;
> + data->x_pos[1] = 0;
> + data->y_pos[0] = 0;
> + data->y_pos[1] = 0;
> + data->previous_press_reported = 0;
> +
> +err:
> + return retval;
> +}
> +
> +#ifdef CONFIG_PM
> +/**
> + * bu21013_suspend() - suspend the touch screen controller
> + * @client: pointer to i2c client structure
> + * @mesg: message from power manager
> + *
> + * This funtion is used to suspend the
> + * touch panel controller and returns integer
> + */
> +static int bu21013_suspend(struct i2c_client *client, pm_message_t
> mesg)
> +{
> + struct bu21013_ts_data *bu21013_data =
> i2c_get_clientdata(client);
> +
> + bu21013_data->touch_stopped = true;
> + wake_up(&bu21013_data->wait);
> + if (device_may_wakeup(&client->dev))
> + enable_irq_wake(bu21013_data->chip->irq);
> + else
> + disable_irq(bu21013_data->chip->irq);
> +
> + return 0;
> +}
> +
> +/**
> + * bu21013_resume() - resume the touch screen controller
> + * @client: pointer to i2c client structure
> + *
> + * This funtion is used to resume the touch panel
> + * controller and returns integer.
> + */
> +static int bu21013_resume(struct i2c_client *client)
> +{
> + int retval;
> + struct bu21013_ts_data *bu21013_data =
> i2c_get_clientdata(client);
> +
> + retval = bu21013_init_chip(bu21013_data);
> + if (retval < 0) {
> + dev_err(&client->dev, "tsc config failed\n");
> + return retval;
> + }
> +
> + bu21013_data->touch_stopped = false;
> + if (device_may_wakeup(&client->dev))
> + disable_irq_wake(bu21013_data->chip->irq);
> + else
> + enable_irq(bu21013_data->chip->irq);
> +
> + return 0;
> +}
> +#endif
> +
> +/**
> + * bu21013_probe() - initialzes the i2c-client touchscreen driver
> + * @i2c: i2c client structure pointer
> + * @id:i2c device id pointer
> + *
> + * This function used to initializes the i2c-client touchscreen
> + * driver and returns integer.
> + */
> +static int __devinit bu21013_probe(struct i2c_client *i2c,
> + const struct i2c_device_id *id)
> +{
> + int retval;
> + struct bu21013_ts_data *bu21013_data;
> + struct input_dev *in_dev;
> + short x_max;
> + short y_max;
> + struct bu21013_platform_device *pdata = i2c->dev.platform_data;
> +
> + if (!i2c) {
> + dev_err(&i2c->dev, "i2c client not defined\n");
> + retval = -EINVAL;
> + return retval;
> + }
> +
> + if (!pdata) {
> + dev_err(&i2c->dev, "platform data not defined\n");
> + retval = -EINVAL;
> + return retval;
> + }
> +
> + bu21013_data = kzalloc(sizeof(struct bu21013_ts_data),
> GFP_KERNEL);
> + if (!bu21013_data) {
> + dev_err(&i2c->dev, "device memory alloc failed\n");
> + retval = -ENOMEM;
> + return retval;
> + }
> +
> + /* allocate input device */
> + in_dev = input_allocate_device();
> + if (!in_dev) {
> + dev_err(&i2c->dev, "input device memory alloc failed\n");
> + retval = -ENOMEM;
> + goto err_alloc;
> + }
> + bu21013_data->in_dev = in_dev;
> +
> + bu21013_data->chip = pdata;
> + bu21013_data->client = i2c;
> + bu21013_data->touch_stopped = false;
> +
> + x_max = pdata->x_max_res;
> + y_max = pdata->y_max_res;
> +
> + init_waitqueue_head(&bu21013_data->wait);
> +
> + i2c_set_clientdata(i2c, bu21013_data);
> +
> + /* configure the gpio pins */
> + if (pdata->cs_en) {
> + retval = pdata->cs_en(pdata->cs_pin);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "chip init failed\n");
> + goto err_init_cs;
> + }
> + }
> +
> + /* configure the touch panel controller */
> + retval = bu21013_init_chip(bu21013_data);
> + if (retval < 0) {
> + dev_err(&i2c->dev, "error in bu21013 config\n");
> + goto err_init_config;
> + }
> +
> + /* register the device to input subsystem */
> + in_dev->name = DRIVER_TP;
> + in_dev->id.bustype = BUS_I2C;
> + in_dev->dev.parent = &i2c->dev;
> + __set_bit(EV_SYN, in_dev->evbit);
> + __set_bit(EV_KEY, in_dev->evbit);
> + __set_bit(EV_ABS, in_dev->evbit);
> + __set_bit(BTN_TOUCH, in_dev->keybit);
> +
> + input_set_abs_params(in_dev, ABS_X, 0, x_max, 0, 0);
> + input_set_abs_params(in_dev, ABS_Y, 0, y_max, 0, 0);
> + input_set_abs_params(in_dev, ABS_PRESSURE, 0, MAX_PRESSURE, 0,
> 0);
> + input_set_abs_params(in_dev, ABS_TOOL_WIDTH, 0, MAX_TOOL_WIDTH,
> 0, 0);
> +
> + if (pdata->multi_touch) {
> + input_set_abs_params(in_dev, ABS_MT_POSITION_X, 0, x_max,
> + 0, 0);
> + input_set_abs_params(in_dev, ABS_MT_POSITION_Y, 0, y_max,
> + 0, 0);
> + input_set_abs_params(in_dev, ABS_MT_TOUCH_MAJOR, 0,
> + MAX_TOUCH_MAJOR, 0, 0);
> + input_set_abs_params(in_dev, ABS_MT_TOUCH_MINOR, 0,
> + MAX_TOUCH_MINOR, 0, 0);
> + input_set_abs_params(in_dev, ABS_MT_ORIENTATION, 0, 1, 0,
> 0);
> + input_set_abs_params(in_dev, ABS_MT_WIDTH_MAJOR, 0,
> + MAX_TOOL_WIDTH, 0, 0);
> + }
> + retval = input_register_device(in_dev);
> + if (retval)
> + goto err_input_register;
> +
> + retval = request_threaded_irq(pdata->irq, NULL, bu21013_gpio_irq,
> + (IRQF_TRIGGER_FALLING | IRQF_SHARED),
> + DRIVER_TP, bu21013_data);
> + if (retval) {
> + dev_err(&i2c->dev, "request irq %d failed\n", pdata->irq);
> + goto err_init_irq;
> + }
> +
> + return retval;
> +
> +err_init_irq:
> + input_unregister_device(bu21013_data->in_dev);
> + bu21013_data->in_dev = NULL;
> +err_input_register:
> +err_init_config:
> + pdata->cs_dis(pdata->cs_pin);
> +err_init_cs:
> + input_free_device(bu21013_data->in_dev);
> +err_alloc:
> + kfree(bu21013_data);
> +
> + return retval;
> +}
> +/**
> + * bu21013_remove() - removes the i2c-client touchscreen driver
> + * @client: i2c client structure pointer
> + *
> + * This function uses to remove the i2c-client
> + * touchscreen driver and returns integer.
> + */
> +static int __devexit bu21013_remove(struct i2c_client *client)
> +{
> + struct bu21013_ts_data *data = i2c_get_clientdata(client);
> +
> + data->touch_stopped = true;
> + free_irq(data->chip->irq, data);
> + data->chip->cs_dis(data->chip->cs_pin);
> + input_unregister_device(data->in_dev);
> + kfree(data);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id bu21013_id[] = {
> + { DRIVER_TP, 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(i2c, bu21013_id);
> +
> +static struct i2c_driver bu21013_driver = {
> + .driver = {
> + .name = DRIVER_TP,
> + .owner = THIS_MODULE,
> + },
> + .probe = bu21013_probe,
> +#ifdef CONFIG_PM
> + .suspend = bu21013_suspend,
> + .resume = bu21013_resume,
> +#endif
> + .remove = __devexit_p(bu21013_remove),
> + .id_table = bu21013_id,
> +};
> +
> +/**
> + * bu21013_init() - initializes the bu21013 touchscreen driver
> + *
> + * This function used to initializes the bu21013
> + * touchscreen driver and returns integer.
> + */
> +static int __init bu21013_init(void)
> +{
> + return i2c_add_driver(&bu21013_driver);
> +}
> +
> +/**
> + * bu21013_exit() - de-initializes the bu21013 touchscreen driver
> + *
> + * This function uses to de-initializes the bu21013
> + * touchscreen driver and returns none.
> + */
> +static void __exit bu21013_exit(void)
> +{
> + i2c_del_driver(&bu21013_driver);
> +}
> +
> +module_init(bu21013_init);
> +module_exit(bu21013_exit);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("NAVEEN KUMAR G<naveen.gaddipati@xxxxxxxxxxxxxx");
> +MODULE_DESCRIPTION("bu21013 touch screen controller driver");
> diff --git a/include/linux/input/bu21013.h
> b/include/linux/input/bu21013.h
> new file mode 100644
> index 0000000..6c64bda
> --- /dev/null
> +++ b/include/linux/input/bu21013.h
> @@ -0,0 +1,44 @@
> +/*
> + * Copyright (C) ST-Ericsson SA 2010
> + * Author: Naveen Kumar G <naveen.gaddipati@xxxxxxxxxxxxxx> for ST-
> Ericsson
> + * License terms:GNU General Public License (GPL) version 2
> + */
> +
> +#ifndef _BU21013_H
> +#define _BU21013_H
> +
> +/**
> + * struct bu21013_platform_device - Handle the platform data
> + * @cs_en: pointer to the cs enable function
> + * @cs_dis: pointer to the cs disable function
> + * @irq_read_val: pointer to read the pen irq value function
> + * @x_max_res: xmax resolution
> + * @y_max_res: ymax resolution
> + * @touch_x_max: touch x max
> + * @touch_y_max: touch y max
> + * @cs_pin: chip select pin
> + * @irq: irq pin
> + * @ext_clk: external clock flag
> + * @x_flip: x flip flag
> + * @y_flip: y flip flag
> + * @multi_touch: multi_touch flag
> + *
> + * This is used to handle the platform data
> + */
> +struct bu21013_platform_device {
> + int (*cs_en)(int reset_pin);
> + int (*cs_dis)(int reset_pin);
> + int (*irq_read_val)(void);
> + int x_max_res;
> + int y_max_res;
> + int touch_x_max;
> + int touch_y_max;
> + unsigned int cs_pin;
> + unsigned int irq;
> + bool ext_clk;
> + bool x_flip;
> + bool y_flip;
> + bool multi_touch;
> +};
> +
> +#endif
> --
> 1.7.2.dirty
>
> Thanks & Regards,
> Naveen
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
