On Fri, 2010-07-30 at 08:07 -0400, Jon Smirl wrote: > On Fri, Jul 30, 2010 at 8:02 AM, Jon Smirl <jonsmirl@xxxxxxxxx> wrote: > > On Fri, Jul 30, 2010 at 7:54 AM, Maxim Levitsky <maximlevitsky@xxxxxxxxx> wrote: > >> On Fri, 2010-07-30 at 07:51 -0400, Jon Smirl wrote: > >>> On Fri, Jul 30, 2010 at 7:36 AM, Maxim Levitsky <maximlevitsky@xxxxxxxxx> wrote: > >>> > On Thu, 2010-07-29 at 23:46 -0400, Andy Walls wrote: > >>> >> On Thu, 2010-07-29 at 22:39 -0400, Jon Smirl wrote: > >>> >> > On Thu, Jul 29, 2010 at 10:17 PM, Maxim Levitsky > >>> >> > <maximlevitsky@xxxxxxxxx> wrote: > >>> >> > > note that error_adjustment module option is added. > >>> >> > > This allows to reduce input samples by a percent. > >>> >> > > This makes input on my system more correct. > >>> >> > > > >>> >> > > Default is 4% as it works best here. > >>> >> > > > >>> >> > > Note that only normal input is adjusted. I don't know > >>> >> > > what adjustments to apply to fan tachometer input. > >>> >> > > Maybe it is accurate already. > >>> >> > > >>> >> > Do you have the manual for the ENE chip in English? or do you read Chinese? > >>> >> > >>> >> The datasheet for a similar chip, the KB3700, is out there in English, > >>> >> but it doesn't have CIR. > >>> >> > >>> >> You might find these links mildly interesting: > >>> >> > >>> >> http://www.coreboot.org/Embedded_controller > >>> >> http://wiki.laptop.org/go/Embedded_controller > >>> >> http://lists.laptop.org/pipermail/openec/2008-July/000108.html > >>> > > >>> > Nope, I have read that. > >>> >> > >>> >> Regards, > >>> >> Andy > >>> >> > >>> >> > Maybe you can figure out why the readings are off by 4%. I suspect > >>> >> > that someone has set a clock divider wrong when programming the chip. > >>> >> > For example setting the divider for a 25Mhz clock when the clock is > >>> >> > actually 26Mhz would cause the error you are seeing. Or they just made > >>> >> > a mistake in computing the divisor. It is probably a bug in the BIOS > >>> >> > of your laptop. If that's the case you could add a quirk in the > >>> >> > system boot code to fix the register setting. > >>> > > >>> > I figured out how windows driver compensates for the offset, and do the > >>> > same in my driver. I think the problem is solved. > >>> > > >>> > >>> Should that be a <= or >= instead of !=? > >>> + if (pll_freq != 1000) > >> > >> This is how its done in windows driver. > > > > That doesn't mean it is bug free. This PLL frequency is likely to be chip internal frequency. And windows driver doesn't touch it. Its embedded controller, so I don't want to touch things I am not sure about. > > > > Experimenting with changing the PLL frequency register may correct the > > error. Try taking 96% of pll_freq and write it back into these > > register. This would be easy to fix with a manual. The root problem is > > almost certainly a bug in the way the PLLs were programmed. > > > > I don't like putting in fudge factors like the 4% correction. What > > happens if a later version of the hardware has fixed firmware? I > > normal user is never going to figure out that they need to change the > > fudge factor. I don't think that is a hardware bug, rather a limitation. Lets leave it as is. I will soon publish the driver on launchpad or something like that and try to contact users I debugged that driver with, and then see what ranges PLL register takes. > > > > + pll_freq = (ene_hw_read_reg(dev, ENE_PLLFRH) << 4) + > > + (ene_hw_read_reg(dev, ENE_PLLFRL) >> 2); > > I can understand the shift of the high bits, but that shift of the low > bits is unlikely. A manual would tell us if it is right. > This shift is correct (according to datasheet, which contains mostly useless info, but it does dociment this reg briefly.) Best regards, Maxim Levitsky -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
