Signed-off-by: Jarod Wilson <jarod@xxxxxxxxxx>
---
drivers/staging/lirc/lirc_sir.c | 1282 +++++++++++++++++++++++++++++++++++++++
1 files changed, 1282 insertions(+), 0 deletions(-)
create mode 100644 drivers/staging/lirc/lirc_sir.c
diff --git a/drivers/staging/lirc/lirc_sir.c b/drivers/staging/lirc/lirc_sir.c
new file mode 100644
index 0000000..97146d1
--- /dev/null
+++ b/drivers/staging/lirc/lirc_sir.c
@@ -0,0 +1,1282 @@
+/*
+ * LIRC SIR driver, (C) 2000 Milan Pikula <www@xxxxxxxxx>
+ *
+ * lirc_sir - Device driver for use with SIR (serial infra red)
+ * mode of IrDA on many notebooks.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * 2000/09/16 Frank Przybylski <mail@xxxxxxxxxxxxxxxxxx> :
+ * added timeout and relaxed pulse detection, removed gap bug
+ *
+ * 2000/12/15 Christoph Bartelmus <lirc@xxxxxxxxxxxx> :
+ * added support for Tekram Irmate 210 (sending does not work yet,
+ * kind of disappointing that nobody was able to implement that
+ * before),
+ * major clean-up
+ *
+ * 2001/02/27 Christoph Bartelmus <lirc@xxxxxxxxxxxx> :
+ * added support for StrongARM SA1100 embedded microprocessor
+ * parts cut'n'pasted from sa1100_ir.c (C) 2000 Russell King
+ */
+
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/fs.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/serial_reg.h>
+#include <linux/time.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/poll.h>
+#include <asm/system.h>
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <linux/fcntl.h>
+#ifdef LIRC_ON_SA1100
+#include <asm/hardware.h>
+#ifdef CONFIG_SA1100_COLLIE
+#include <asm/arch/tc35143.h>
+#include <asm/ucb1200.h>
+#endif
+#endif
+
+#include <linux/timer.h>
+
+#include <media/lirc.h>
+#include <media/lirc_dev.h>
+
+/* SECTION: Definitions */
+
+/*** Tekram dongle ***/
+#ifdef LIRC_SIR_TEKRAM
+/* stolen from kernel source */
+/* definitions for Tekram dongle */
+#define TEKRAM_115200 0x00
+#define TEKRAM_57600 0x01
+#define TEKRAM_38400 0x02
+#define TEKRAM_19200 0x03
+#define TEKRAM_9600 0x04
+#define TEKRAM_2400 0x08
+
+#define TEKRAM_PW 0x10 /* Pulse select bit */
+
+/* 10bit * 1s/115200bit in milliseconds = 87ms*/
+#define TIME_CONST (10000000ul/115200ul)
+
+#endif
+
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+static void init_act200(void);
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+static void init_act220(void);
+#endif
+
+/*** SA1100 ***/
+#ifdef LIRC_ON_SA1100
+struct sa1100_ser2_registers {
+ /* HSSP control register */
+ unsigned char hscr0;
+ /* UART registers */
+ unsigned char utcr0;
+ unsigned char utcr1;
+ unsigned char utcr2;
+ unsigned char utcr3;
+ unsigned char utcr4;
+ unsigned char utdr;
+ unsigned char utsr0;
+ unsigned char utsr1;
+} sr;
+
+static int irq = IRQ_Ser2ICP;
+
+#define LIRC_ON_SA1100_TRANSMITTER_LATENCY 0
+
+/* pulse/space ratio of 50/50 */
+static unsigned long pulse_width = (13-LIRC_ON_SA1100_TRANSMITTER_LATENCY);
+/* 1000000/freq-pulse_width */
+static unsigned long space_width = (13-LIRC_ON_SA1100_TRANSMITTER_LATENCY);
+static unsigned int freq = 38000; /* modulation frequency */
+static unsigned int duty_cycle = 50; /* duty cycle of 50% */
+
+#endif
+
+#define RBUF_LEN 1024
+#define WBUF_LEN 1024
+
+#define LIRC_DRIVER_NAME "lirc_sir"
+
+#define PULSE '['
+
+#ifndef LIRC_SIR_TEKRAM
+/* 9bit * 1s/115200bit in milli seconds = 78.125ms*/
+#define TIME_CONST (9000000ul/115200ul)
+#endif
+
+
+/* timeout for sequences in jiffies (=5/100s), must be longer than TIME_CONST */
+#define SIR_TIMEOUT (HZ*5/100)
+
+#ifndef LIRC_ON_SA1100
+#ifndef LIRC_IRQ
+#define LIRC_IRQ 4
+#endif
+#ifndef LIRC_PORT
+/* for external dongles, default to com1 */
+#if defined(LIRC_SIR_ACTISYS_ACT200L) || \
+ defined(LIRC_SIR_ACTISYS_ACT220L) || \
+ defined(LIRC_SIR_TEKRAM)
+#define LIRC_PORT 0x3f8
+#else
+/* onboard sir ports are typically com3 */
+#define LIRC_PORT 0x3e8
+#endif
+#endif
+
+static int io = LIRC_PORT;
+static int irq = LIRC_IRQ;
+static int threshold = 3;
+#endif
+
+static DEFINE_SPINLOCK(timer_lock);
+static struct timer_list timerlist;
+/* time of last signal change detected */
+static struct timeval last_tv = {0, 0};
+/* time of last UART data ready interrupt */
+static struct timeval last_intr_tv = {0, 0};
+static int last_value;
+
+static DECLARE_WAIT_QUEUE_HEAD(lirc_read_queue);
+
+static DEFINE_SPINLOCK(hardware_lock);
+
+static int rx_buf[RBUF_LEN];
+static unsigned int rx_tail, rx_head;
+
+static int debug;
+#define dprintk(fmt, args...) \
+ do { \
+ if (debug) \
+ printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \
+ fmt, ## args); \
+ } while (0)
+
+/* SECTION: Prototypes */
+
+/* Communication with user-space */
+static unsigned int lirc_poll(struct file *file, poll_table *wait);
+static ssize_t lirc_read(struct file *file, char *buf, size_t count,
+ loff_t *ppos);
+static ssize_t lirc_write(struct file *file, const char *buf, size_t n,
+ loff_t *pos);
+static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg);
+static void add_read_queue(int flag, unsigned long val);
+static int init_chrdev(void);
+static void drop_chrdev(void);
+/* Hardware */
+static irqreturn_t sir_interrupt(int irq, void *dev_id);
+static void send_space(unsigned long len);
+static void send_pulse(unsigned long len);
+static int init_hardware(void);
+static void drop_hardware(void);
+/* Initialisation */
+static int init_port(void);
+static void drop_port(void);
+
+#ifdef LIRC_ON_SA1100
+static void on(void)
+{
+ PPSR |= PPC_TXD2;
+}
+
+static void off(void)
+{
+ PPSR &= ~PPC_TXD2;
+}
+#else
+static inline unsigned int sinp(int offset)
+{
+ return inb(io + offset);
+}
+
+static inline void soutp(int offset, int value)
+{
+ outb(value, io + offset);
+}
+#endif
+
+#ifndef MAX_UDELAY_MS
+#define MAX_UDELAY_US 5000
+#else
+#define MAX_UDELAY_US (MAX_UDELAY_MS*1000)
+#endif
+
+static void safe_udelay(unsigned long usecs)
+{
+ while (usecs > MAX_UDELAY_US) {
+ udelay(MAX_UDELAY_US);
+ usecs -= MAX_UDELAY_US;
+ }
+ udelay(usecs);
+}
+
+/* SECTION: Communication with user-space */
+
+static unsigned int lirc_poll(struct file *file, poll_table *wait)
+{
+ poll_wait(file, &lirc_read_queue, wait);
+ if (rx_head != rx_tail)
+ return POLLIN | POLLRDNORM;
+ return 0;
+}
+
+static ssize_t lirc_read(struct file *file, char *buf, size_t count,
+ loff_t *ppos)
+{
+ int n = 0;
+ int retval = 0;
+ DECLARE_WAITQUEUE(wait, current);
+
+ if (count % sizeof(int))
+ return -EINVAL;
+
+ add_wait_queue(&lirc_read_queue, &wait);
+ set_current_state(TASK_INTERRUPTIBLE);
+ while (n < count) {
+ if (rx_head != rx_tail) {
+ if (copy_to_user((void *) buf + n,
+ (void *) (rx_buf + rx_head),
+ sizeof(int))) {
+ retval = -EFAULT;
+ break;
+ }
+ rx_head = (rx_head + 1) & (RBUF_LEN - 1);
+ n += sizeof(int);
+ } else {
+ if (file->f_flags & O_NONBLOCK) {
+ retval = -EAGAIN;
+ break;
+ }
+ if (signal_pending(current)) {
+ retval = -ERESTARTSYS;
+ break;
+ }
+ schedule();
+ set_current_state(TASK_INTERRUPTIBLE);
+ }
+ }
+ remove_wait_queue(&lirc_read_queue, &wait);
+ set_current_state(TASK_RUNNING);
+ return n ? n : retval;
+}
+static ssize_t lirc_write(struct file *file, const char *buf, size_t n,
+ loff_t *pos)
+{
+ unsigned long flags;
+ int i, count;
+ int *tx_buf;
+
+ count = n / sizeof(int);
+ if (n % sizeof(int) || count % 2 == 0)
+ return -EINVAL;
+ tx_buf = memdup_user(buf, n);
+ if (IS_ERR(tx_buf))
+ return PTR_ERR(tx_buf);
+ i = 0;
+#ifdef LIRC_ON_SA1100
+ /* disable receiver */
+ Ser2UTCR3 = 0;
+#endif
+ local_irq_save(flags);
+ while (1) {
+ if (i >= count)
+ break;
+ if (tx_buf[i])
+ send_pulse(tx_buf[i]);
+ i++;
+ if (i >= count)
+ break;
+ if (tx_buf[i])
+ send_space(tx_buf[i]);
+ i++;
+ }
+ local_irq_restore(flags);
+#ifdef LIRC_ON_SA1100
+ off();
+ udelay(1000); /* wait 1ms for IR diode to recover */
+ Ser2UTCR3 = 0;
+ /* clear status register to prevent unwanted interrupts */
+ Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+ /* enable receiver */
+ Ser2UTCR3 = UTCR3_RXE|UTCR3_RIE;
+#endif
+ return count;
+}
+
+static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg)
+{
+ int retval = 0;
+ unsigned long value = 0;
+#ifdef LIRC_ON_SA1100
+ unsigned int ivalue;
+
+ if (cmd == LIRC_GET_FEATURES)
+ value = LIRC_CAN_SEND_PULSE |
+ LIRC_CAN_SET_SEND_DUTY_CYCLE |
+ LIRC_CAN_SET_SEND_CARRIER |
+ LIRC_CAN_REC_MODE2;
+ else if (cmd == LIRC_GET_SEND_MODE)
+ value = LIRC_MODE_PULSE;
+ else if (cmd == LIRC_GET_REC_MODE)
+ value = LIRC_MODE_MODE2;
+#else
+ if (cmd == LIRC_GET_FEATURES)
+ value = LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2;
+ else if (cmd == LIRC_GET_SEND_MODE)
+ value = LIRC_MODE_PULSE;
+ else if (cmd == LIRC_GET_REC_MODE)
+ value = LIRC_MODE_MODE2;
+#endif
+
+ switch (cmd) {
+ case LIRC_GET_FEATURES:
+ case LIRC_GET_SEND_MODE:
+ case LIRC_GET_REC_MODE:
+ retval = put_user(value, (unsigned long *) arg);
+ break;
+
+ case LIRC_SET_SEND_MODE:
+ case LIRC_SET_REC_MODE:
+ retval = get_user(value, (unsigned long *) arg);
+ break;
+#ifdef LIRC_ON_SA1100
+ case LIRC_SET_SEND_DUTY_CYCLE:
+ retval = get_user(ivalue, (unsigned int *) arg);
+ if (retval)
+ return retval;
+ if (ivalue <= 0 || ivalue > 100)
+ return -EINVAL;
+ /* (ivalue/100)*(1000000/freq) */
+ duty_cycle = ivalue;
+ pulse_width = (unsigned long) duty_cycle*10000/freq;
+ space_width = (unsigned long) 1000000L/freq-pulse_width;
+ if (pulse_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+ pulse_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+ if (space_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+ space_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+ break;
+ case LIRC_SET_SEND_CARRIER:
+ retval = get_user(ivalue, (unsigned int *) arg);
+ if (retval)
+ return retval;
+ if (ivalue > 500000 || ivalue < 20000)
+ return -EINVAL;
+ freq = ivalue;
+ pulse_width = (unsigned long) duty_cycle*10000/freq;
+ space_width = (unsigned long) 1000000L/freq-pulse_width;
+ if (pulse_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+ pulse_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+ if (space_width >= LIRC_ON_SA1100_TRANSMITTER_LATENCY)
+ space_width -= LIRC_ON_SA1100_TRANSMITTER_LATENCY;
+ break;
+#endif
+ default:
+ retval = -ENOIOCTLCMD;
+
+ }
+
+ if (retval)
+ return retval;
+ if (cmd == LIRC_SET_REC_MODE) {
+ if (value != LIRC_MODE_MODE2)
+ retval = -ENOSYS;
+ } else if (cmd == LIRC_SET_SEND_MODE) {
+ if (value != LIRC_MODE_PULSE)
+ retval = -ENOSYS;
+ }
+
+ return retval;
+}
+
+static void add_read_queue(int flag, unsigned long val)
+{
+ unsigned int new_rx_tail;
+ int newval;
+
+ dprintk("add flag %d with val %lu\n", flag, val);
+
+ newval = val & PULSE_MASK;
+
+ /*
+ * statistically, pulses are ~TIME_CONST/2 too long. we could
+ * maybe make this more exact, but this is good enough
+ */
+ if (flag) {
+ /* pulse */
+ if (newval > TIME_CONST/2)
+ newval -= TIME_CONST/2;
+ else /* should not ever happen */
+ newval = 1;
+ newval |= PULSE_BIT;
+ } else {
+ newval += TIME_CONST/2;
+ }
+ new_rx_tail = (rx_tail + 1) & (RBUF_LEN - 1);
+ if (new_rx_tail == rx_head) {
+ dprintk("Buffer overrun.\n");
+ return;
+ }
+ rx_buf[rx_tail] = newval;
+ rx_tail = new_rx_tail;
+ wake_up_interruptible(&lirc_read_queue);
+}
+
+static struct file_operations lirc_fops = {
+ .owner = THIS_MODULE,
+ .read = lirc_read,
+ .write = lirc_write,
+ .poll = lirc_poll,
+ .unlocked_ioctl = lirc_ioctl,
+ .open = lirc_dev_fop_open,
+ .release = lirc_dev_fop_close,
+};
+
+static int set_use_inc(void *data)
+{
+ return 0;
+}
+
+static void set_use_dec(void *data)
+{
+}
+
+static struct lirc_driver driver = {
+ .name = LIRC_DRIVER_NAME,
+ .minor = -1,
+ .code_length = 1,
+ .sample_rate = 0,
+ .data = NULL,
+ .add_to_buf = NULL,
+ .set_use_inc = set_use_inc,
+ .set_use_dec = set_use_dec,
+ .fops = &lirc_fops,
+ .dev = NULL,
+ .owner = THIS_MODULE,
+};
+
+
+static int init_chrdev(void)
+{
+ driver.minor = lirc_register_driver(&driver);
+ if (driver.minor < 0) {
+ printk(KERN_ERR LIRC_DRIVER_NAME ": init_chrdev() failed.\n");
+ return -EIO;
+ }
+ return 0;
+}
+
+static void drop_chrdev(void)
+{
+ lirc_unregister_driver(driver.minor);
+}
+
+/* SECTION: Hardware */
+static long delta(struct timeval *tv1, struct timeval *tv2)
+{
+ unsigned long deltv;
+
+ deltv = tv2->tv_sec - tv1->tv_sec;
+ if (deltv > 15)
+ deltv = 0xFFFFFF;
+ else
+ deltv = deltv*1000000 +
+ tv2->tv_usec -
+ tv1->tv_usec;
+ return deltv;
+}
+
+static void sir_timeout(unsigned long data)
+{
+ /*
+ * if last received signal was a pulse, but receiving stopped
+ * within the 9 bit frame, we need to finish this pulse and
+ * simulate a signal change to from pulse to space. Otherwise
+ * upper layers will receive two sequences next time.
+ */
+
+ unsigned long flags;
+ unsigned long pulse_end;
+
+ /* avoid interference with interrupt */
+ spin_lock_irqsave(&timer_lock, flags);
+ if (last_value) {
+#ifndef LIRC_ON_SA1100
+ /* clear unread bits in UART and restart */
+ outb(UART_FCR_CLEAR_RCVR, io + UART_FCR);
+#endif
+ /* determine 'virtual' pulse end: */
+ pulse_end = delta(&last_tv, &last_intr_tv);
+ dprintk("timeout add %d for %lu usec\n", last_value, pulse_end);
+ add_read_queue(last_value, pulse_end);
+ last_value = 0;
+ last_tv = last_intr_tv;
+ }
+ spin_unlock_irqrestore(&timer_lock, flags);
+}
+
+static irqreturn_t sir_interrupt(int irq, void *dev_id)
+{
+ unsigned char data;
+ struct timeval curr_tv;
+ static unsigned long deltv;
+#ifdef LIRC_ON_SA1100
+ int status;
+ static int n;
+
+ status = Ser2UTSR0;
+ /*
+ * Deal with any receive errors first. The bytes in error may be
+ * the only bytes in the receive FIFO, so we do this first.
+ */
+ while (status & UTSR0_EIF) {
+ int bstat;
+
+ if (debug) {
+ dprintk("EIF\n");
+ bstat = Ser2UTSR1;
+
+ if (bstat & UTSR1_FRE)
+ dprintk("frame error\n");
+ if (bstat & UTSR1_ROR)
+ dprintk("receive fifo overrun\n");
+ if (bstat & UTSR1_PRE)
+ dprintk("parity error\n");
+ }
+
+ bstat = Ser2UTDR;
+ n++;
+ status = Ser2UTSR0;
+ }
+
+ if (status & (UTSR0_RFS | UTSR0_RID)) {
+ do_gettimeofday(&curr_tv);
+ deltv = delta(&last_tv, &curr_tv);
+ do {
+ data = Ser2UTDR;
+ dprintk("%d data: %u\n", n, (unsigned int) data);
+ n++;
+ } while (status & UTSR0_RID && /* do not empty fifo in order to
+ * get UTSR0_RID in any case */
+ Ser2UTSR1 & UTSR1_RNE); /* data ready */
+
+ if (status&UTSR0_RID) {
+ add_read_queue(0 , deltv - n * TIME_CONST); /*space*/
+ add_read_queue(1, n * TIME_CONST); /*pulse*/
+ n = 0;
+ last_tv = curr_tv;
+ }
+ }
+
+ if (status & UTSR0_TFS)
+ printk(KERN_ERR "transmit fifo not full, shouldn't happen\n");
+
+ /* We must clear certain bits. */
+ status &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+ if (status)
+ Ser2UTSR0 = status;
+#else
+ unsigned long deltintrtv;
+ unsigned long flags;
+ int iir, lsr;
+
+ while ((iir = inb(io + UART_IIR) & UART_IIR_ID)) {
+ switch (iir&UART_IIR_ID) { /* FIXME toto treba preriedit */
+ case UART_IIR_MSI:
+ (void) inb(io + UART_MSR);
+ break;
+ case UART_IIR_RLSI:
+ (void) inb(io + UART_LSR);
+ break;
+ case UART_IIR_THRI:
+#if 0
+ if (lsr & UART_LSR_THRE) /* FIFO is empty */
+ outb(data, io + UART_TX)
+#endif
+ break;
+ case UART_IIR_RDI:
+ /* avoid interference with timer */
+ spin_lock_irqsave(&timer_lock, flags);
+ do {
+ del_timer(&timerlist);
+ data = inb(io + UART_RX);
+ do_gettimeofday(&curr_tv);
+ deltv = delta(&last_tv, &curr_tv);
+ deltintrtv = delta(&last_intr_tv, &curr_tv);
+ dprintk("t %lu, d %d\n", deltintrtv, (int)data);
+ /*
+ * if nothing came in last X cycles,
+ * it was gap
+ */
+ if (deltintrtv > TIME_CONST * threshold) {
+ if (last_value) {
+ dprintk("GAP\n");
+ /* simulate signal change */
+ add_read_queue(last_value,
+ deltv -
+ deltintrtv);
+ last_value = 0;
+ last_tv.tv_sec =
+ last_intr_tv.tv_sec;
+ last_tv.tv_usec =
+ last_intr_tv.tv_usec;
+ deltv = deltintrtv;
+ }
+ }
+ data = 1;
+ if (data ^ last_value) {
+ /*
+ * deltintrtv > 2*TIME_CONST, remember?
+ * the other case is timeout
+ */
+ add_read_queue(last_value,
+ deltv-TIME_CONST);
+ last_value = data;
+ last_tv = curr_tv;
+ if (last_tv.tv_usec >= TIME_CONST) {
+ last_tv.tv_usec -= TIME_CONST;
+ } else {
+ last_tv.tv_sec--;
+ last_tv.tv_usec += 1000000 -
+ TIME_CONST;
+ }
+ }
+ last_intr_tv = curr_tv;
+ if (data) {
+ /*
+ * start timer for end of
+ * sequence detection
+ */
+ timerlist.expires = jiffies +
+ SIR_TIMEOUT;
+ add_timer(&timerlist);
+ }
+
+ lsr = inb(io + UART_LSR);
+ } while (lsr & UART_LSR_DR); /* data ready */
+ spin_unlock_irqrestore(&timer_lock, flags);
+ break;
+ default:
+ break;
+ }
+ }
+#endif
+ return IRQ_RETVAL(IRQ_HANDLED);
+}
+
+#ifdef LIRC_ON_SA1100
+static void send_pulse(unsigned long length)
+{
+ unsigned long k, delay;
+ int flag;
+
+ if (length == 0)
+ return;
+ /*
+ * this won't give us the carrier frequency we really want
+ * due to integer arithmetic, but we can accept this inaccuracy
+ */
+
+ for (k = flag = 0; k < length; k += delay, flag = !flag) {
+ if (flag) {
+ off();
+ delay = space_width;
+ } else {
+ on();
+ delay = pulse_width;
+ }
+ safe_udelay(delay);
+ }
+ off();
+}
+
+static void send_space(unsigned long length)
+{
+ if (length == 0)
+ return;
+ off();
+ safe_udelay(length);
+}
+#else
+static void send_space(unsigned long len)
+{
+ safe_udelay(len);
+}
+
+static void send_pulse(unsigned long len)
+{
+ long bytes_out = len / TIME_CONST;
+ long time_left;
+
+ time_left = (long)len - (long)bytes_out * (long)TIME_CONST;
+ if (bytes_out == 0) {
+ bytes_out++;
+ time_left = 0;
+ }
+ while (bytes_out--) {
+ outb(PULSE, io + UART_TX);
+ /* FIXME treba seriozne cakanie z char/serial.c */
+ while (!(inb(io + UART_LSR) & UART_LSR_THRE))
+ ;
+ }
+#if 0
+ if (time_left > 0)
+ safe_udelay(time_left);
+#endif
+}
+#endif
+
+#ifdef CONFIG_SA1100_COLLIE
+static int sa1100_irda_set_power_collie(int state)
+{
+ if (state) {
+ /*
+ * 0 - off
+ * 1 - short range, lowest power
+ * 2 - medium range, medium power
+ * 3 - maximum range, high power
+ */
+ ucb1200_set_io_direction(TC35143_GPIO_IR_ON,
+ TC35143_IODIR_OUTPUT);
+ ucb1200_set_io(TC35143_GPIO_IR_ON, TC35143_IODAT_LOW);
+ udelay(100);
+ } else {
+ /* OFF */
+ ucb1200_set_io_direction(TC35143_GPIO_IR_ON,
+ TC35143_IODIR_OUTPUT);
+ ucb1200_set_io(TC35143_GPIO_IR_ON, TC35143_IODAT_HIGH);
+ }
+ return 0;
+}
+#endif
+
+static int init_hardware(void)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&hardware_lock, flags);
+ /* reset UART */
+#ifdef LIRC_ON_SA1100
+#ifdef CONFIG_SA1100_BITSY
+ if (machine_is_bitsy()) {
+ printk(KERN_INFO "Power on IR module\n");
+ set_bitsy_egpio(EGPIO_BITSY_IR_ON);
+ }
+#endif
+#ifdef CONFIG_SA1100_COLLIE
+ sa1100_irda_set_power_collie(3); /* power on */
+#endif
+ sr.hscr0 = Ser2HSCR0;
+
+ sr.utcr0 = Ser2UTCR0;
+ sr.utcr1 = Ser2UTCR1;
+ sr.utcr2 = Ser2UTCR2;
+ sr.utcr3 = Ser2UTCR3;
+ sr.utcr4 = Ser2UTCR4;
+
+ sr.utdr = Ser2UTDR;
+ sr.utsr0 = Ser2UTSR0;
+ sr.utsr1 = Ser2UTSR1;
+
+ /* configure GPIO */
+ /* output */
+ PPDR |= PPC_TXD2;
+ PSDR |= PPC_TXD2;
+ /* set output to 0 */
+ off();
+
+ /* Enable HP-SIR modulation, and ensure that the port is disabled. */
+ Ser2UTCR3 = 0;
+ Ser2HSCR0 = sr.hscr0 & (~HSCR0_HSSP);
+
+ /* clear status register to prevent unwanted interrupts */
+ Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+
+ /* 7N1 */
+ Ser2UTCR0 = UTCR0_1StpBit|UTCR0_7BitData;
+ /* 115200 */
+ Ser2UTCR1 = 0;
+ Ser2UTCR2 = 1;
+ /* use HPSIR, 1.6 usec pulses */
+ Ser2UTCR4 = UTCR4_HPSIR|UTCR4_Z1_6us;
+
+ /* enable receiver, receive fifo interrupt */
+ Ser2UTCR3 = UTCR3_RXE|UTCR3_RIE;
+
+ /* clear status register to prevent unwanted interrupts */
+ Ser2UTSR0 &= (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
+
+#elif defined(LIRC_SIR_TEKRAM)
+ /* disable FIFO */
+ soutp(UART_FCR,
+ UART_FCR_CLEAR_RCVR|
+ UART_FCR_CLEAR_XMIT|
+ UART_FCR_TRIGGER_1);
+
+ /* Set DLAB 0. */
+ soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+ /* First of all, disable all interrupts */
+ soutp(UART_IER, sinp(UART_IER) &
+ (~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI)));
+
+ /* Set DLAB 1. */
+ soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+ /* Set divisor to 12 => 9600 Baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 12);
+
+ /* Set DLAB 0. */
+ soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+ /* power supply */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ safe_udelay(50*1000);
+
+ /* -DTR low -> reset PIC */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+ udelay(1*1000);
+
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(100);
+
+
+ /* -RTS low -> send control byte */
+ soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(7);
+ soutp(UART_TX, TEKRAM_115200|TEKRAM_PW);
+
+ /* one byte takes ~1042 usec to transmit at 9600,8N1 */
+ udelay(1500);
+
+ /* back to normal operation */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(50);
+
+ udelay(1500);
+
+ /* read previous control byte */
+ printk(KERN_INFO LIRC_DRIVER_NAME
+ ": 0x%02x\n", sinp(UART_RX));
+
+ /* Set DLAB 1. */
+ soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+ /* Set divisor to 1 => 115200 Baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 1);
+
+ /* Set DLAB 0, 8 Bit */
+ soutp(UART_LCR, UART_LCR_WLEN8);
+ /* enable interrupts */
+ soutp(UART_IER, sinp(UART_IER)|UART_IER_RDI);
+#else
+ outb(0, io + UART_MCR);
+ outb(0, io + UART_IER);
+ /* init UART */
+ /* set DLAB, speed = 115200 */
+ outb(UART_LCR_DLAB | UART_LCR_WLEN7, io + UART_LCR);
+ outb(1, io + UART_DLL); outb(0, io + UART_DLM);
+ /* 7N1+start = 9 bits at 115200 ~ 3 bits at 44000 */
+ outb(UART_LCR_WLEN7, io + UART_LCR);
+ /* FIFO operation */
+ outb(UART_FCR_ENABLE_FIFO, io + UART_FCR);
+ /* interrupts */
+ /* outb(UART_IER_RLSI|UART_IER_RDI|UART_IER_THRI, io + UART_IER); */
+ outb(UART_IER_RDI, io + UART_IER);
+ /* turn on UART */
+ outb(UART_MCR_DTR|UART_MCR_RTS|UART_MCR_OUT2, io + UART_MCR);
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+ init_act200();
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+ init_act220();
+#endif
+#endif
+ spin_unlock_irqrestore(&hardware_lock, flags);
+ return 0;
+}
+
+static void drop_hardware(void)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&hardware_lock, flags);
+
+#ifdef LIRC_ON_SA1100
+ Ser2UTCR3 = 0;
+
+ Ser2UTCR0 = sr.utcr0;
+ Ser2UTCR1 = sr.utcr1;
+ Ser2UTCR2 = sr.utcr2;
+ Ser2UTCR4 = sr.utcr4;
+ Ser2UTCR3 = sr.utcr3;
+
+ Ser2HSCR0 = sr.hscr0;
+#ifdef CONFIG_SA1100_BITSY
+ if (machine_is_bitsy())
+ clr_bitsy_egpio(EGPIO_BITSY_IR_ON);
+#endif
+#ifdef CONFIG_SA1100_COLLIE
+ sa1100_irda_set_power_collie(0); /* power off */
+#endif
+#else
+ /* turn off interrupts */
+ outb(0, io + UART_IER);
+#endif
+ spin_unlock_irqrestore(&hardware_lock, flags);
+}
+
+/* SECTION: Initialisation */
+
+static int init_port(void)
+{
+ int retval;
+
+ /* get I/O port access and IRQ line */
+#ifndef LIRC_ON_SA1100
+ if (request_region(io, 8, LIRC_DRIVER_NAME) == NULL) {
+ printk(KERN_ERR LIRC_DRIVER_NAME
+ ": i/o port 0x%.4x already in use.\n", io);
+ return -EBUSY;
+ }
+#endif
+ retval = request_irq(irq, sir_interrupt, IRQF_DISABLED,
+ LIRC_DRIVER_NAME, NULL);
+ if (retval < 0) {
+# ifndef LIRC_ON_SA1100
+ release_region(io, 8);
+# endif
+ printk(KERN_ERR LIRC_DRIVER_NAME
+ ": IRQ %d already in use.\n",
+ irq);
+ return retval;
+ }
+#ifndef LIRC_ON_SA1100
+ printk(KERN_INFO LIRC_DRIVER_NAME
+ ": I/O port 0x%.4x, IRQ %d.\n",
+ io, irq);
+#endif
+
+ init_timer(&timerlist);
+ timerlist.function = sir_timeout;
+ timerlist.data = 0xabadcafe;
+
+ return 0;
+}
+
+static void drop_port(void)
+{
+ free_irq(irq, NULL);
+ del_timer_sync(&timerlist);
+#ifndef LIRC_ON_SA1100
+ release_region(io, 8);
+#endif
+}
+
+#ifdef LIRC_SIR_ACTISYS_ACT200L
+/* Crystal/Cirrus CS8130 IR transceiver, used in Actisys Act200L dongle */
+/* some code borrowed from Linux IRDA driver */
+
+/* Register 0: Control register #1 */
+#define ACT200L_REG0 0x00
+#define ACT200L_TXEN 0x01 /* Enable transmitter */
+#define ACT200L_RXEN 0x02 /* Enable receiver */
+#define ACT200L_ECHO 0x08 /* Echo control chars */
+
+/* Register 1: Control register #2 */
+#define ACT200L_REG1 0x10
+#define ACT200L_LODB 0x01 /* Load new baud rate count value */
+#define ACT200L_WIDE 0x04 /* Expand the maximum allowable pulse */
+
+/* Register 3: Transmit mode register #2 */
+#define ACT200L_REG3 0x30
+#define ACT200L_B0 0x01 /* DataBits, 0=6, 1=7, 2=8, 3=9(8P) */
+#define ACT200L_B1 0x02 /* DataBits, 0=6, 1=7, 2=8, 3=9(8P) */
+#define ACT200L_CHSY 0x04 /* StartBit Synced 0=bittime, 1=startbit */
+
+/* Register 4: Output Power register */
+#define ACT200L_REG4 0x40
+#define ACT200L_OP0 0x01 /* Enable LED1C output */
+#define ACT200L_OP1 0x02 /* Enable LED2C output */
+#define ACT200L_BLKR 0x04
+
+/* Register 5: Receive Mode register */
+#define ACT200L_REG5 0x50
+#define ACT200L_RWIDL 0x01 /* fixed 1.6us pulse mode */
+ /*.. other various IRDA bit modes, and TV remote modes..*/
+
+/* Register 6: Receive Sensitivity register #1 */
+#define ACT200L_REG6 0x60
+#define ACT200L_RS0 0x01 /* receive threshold bit 0 */
+#define ACT200L_RS1 0x02 /* receive threshold bit 1 */
+
+/* Register 7: Receive Sensitivity register #2 */
+#define ACT200L_REG7 0x70
+#define ACT200L_ENPOS 0x04 /* Ignore the falling edge */
+
+/* Register 8,9: Baud Rate Divider register #1,#2 */
+#define ACT200L_REG8 0x80
+#define ACT200L_REG9 0x90
+
+#define ACT200L_2400 0x5f
+#define ACT200L_9600 0x17
+#define ACT200L_19200 0x0b
+#define ACT200L_38400 0x05
+#define ACT200L_57600 0x03
+#define ACT200L_115200 0x01
+
+/* Register 13: Control register #3 */
+#define ACT200L_REG13 0xd0
+#define ACT200L_SHDW 0x01 /* Enable access to shadow registers */
+
+/* Register 15: Status register */
+#define ACT200L_REG15 0xf0
+
+/* Register 21: Control register #4 */
+#define ACT200L_REG21 0x50
+#define ACT200L_EXCK 0x02 /* Disable clock output driver */
+#define ACT200L_OSCL 0x04 /* oscillator in low power, medium accuracy mode */
+
+static void init_act200(void)
+{
+ int i;
+ __u8 control[] = {
+ ACT200L_REG15,
+ ACT200L_REG13 | ACT200L_SHDW,
+ ACT200L_REG21 | ACT200L_EXCK | ACT200L_OSCL,
+ ACT200L_REG13,
+ ACT200L_REG7 | ACT200L_ENPOS,
+ ACT200L_REG6 | ACT200L_RS0 | ACT200L_RS1,
+ ACT200L_REG5 | ACT200L_RWIDL,
+ ACT200L_REG4 | ACT200L_OP0 | ACT200L_OP1 | ACT200L_BLKR,
+ ACT200L_REG3 | ACT200L_B0,
+ ACT200L_REG0 | ACT200L_TXEN | ACT200L_RXEN,
+ ACT200L_REG8 | (ACT200L_115200 & 0x0f),
+ ACT200L_REG9 | ((ACT200L_115200 >> 4) & 0x0f),
+ ACT200L_REG1 | ACT200L_LODB | ACT200L_WIDE
+ };
+
+ /* Set DLAB 1. */
+ soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+
+ /* Set divisor to 12 => 9600 Baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 12);
+
+ /* Set DLAB 0. */
+ soutp(UART_LCR, UART_LCR_WLEN8);
+ /* Set divisor to 12 => 9600 Baud */
+
+ /* power supply */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ for (i = 0; i < 50; i++)
+ safe_udelay(1000);
+
+ /* Reset the dongle : set RTS low for 25 ms */
+ soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+ for (i = 0; i < 25; i++)
+ udelay(1000);
+
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(100);
+
+ /* Clear DTR and set RTS to enter command mode */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+ udelay(7);
+
+ /* send out the control register settings for 115K 7N1 SIR operation */
+ for (i = 0; i < sizeof(control); i++) {
+ soutp(UART_TX, control[i]);
+ /* one byte takes ~1042 usec to transmit at 9600,8N1 */
+ udelay(1500);
+ }
+
+ /* back to normal operation */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(50);
+
+ udelay(1500);
+ soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
+
+ /* Set DLAB 1. */
+ soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN7);
+
+ /* Set divisor to 1 => 115200 Baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 1);
+
+ /* Set DLAB 0. */
+ soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
+
+ /* Set DLAB 0, 7 Bit */
+ soutp(UART_LCR, UART_LCR_WLEN7);
+
+ /* enable interrupts */
+ soutp(UART_IER, sinp(UART_IER)|UART_IER_RDI);
+}
+#endif
+
+#ifdef LIRC_SIR_ACTISYS_ACT220L
+/*
+ * Derived from linux IrDA driver (net/irda/actisys.c)
+ * Drop me a mail for any kind of comment: maxx@xxxxxxxxxxxxx
+ */
+
+void init_act220(void)
+{
+ int i;
+
+ /* DLAB 1 */
+ soutp(UART_LCR, UART_LCR_DLAB|UART_LCR_WLEN7);
+
+ /* 9600 baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 12);
+
+ /* DLAB 0 */
+ soutp(UART_LCR, UART_LCR_WLEN7);
+
+ /* reset the dongle, set DTR low for 10us */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2);
+ udelay(10);
+
+ /* back to normal (still 9600) */
+ soutp(UART_MCR, UART_MCR_DTR|UART_MCR_RTS|UART_MCR_OUT2);
+
+ /*
+ * send RTS pulses until we reach 115200
+ * i hope this is really the same for act220l/act220l+
+ */
+ for (i = 0; i < 3; i++) {
+ udelay(10);
+ /* set RTS low for 10 us */
+ soutp(UART_MCR, UART_MCR_DTR|UART_MCR_OUT2);
+ udelay(10);
+ /* set RTS high for 10 us */
+ soutp(UART_MCR, UART_MCR_RTS|UART_MCR_DTR|UART_MCR_OUT2);
+ }
+
+ /* back to normal operation */
+ udelay(1500); /* better safe than sorry ;) */
+
+ /* Set DLAB 1. */
+ soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN7);
+
+ /* Set divisor to 1 => 115200 Baud */
+ soutp(UART_DLM, 0);
+ soutp(UART_DLL, 1);
+
+ /* Set DLAB 0, 7 Bit */
+ /* The dongle doesn't seem to have any problems with operation at 7N1 */
+ soutp(UART_LCR, UART_LCR_WLEN7);
+
+ /* enable interrupts */
+ soutp(UART_IER, UART_IER_RDI);
+}
+#endif
+
+static int init_lirc_sir(void)
+{
+ int retval;
+
+ init_waitqueue_head(&lirc_read_queue);
+ retval = init_port();
+ if (retval < 0)
+ return retval;
+ init_hardware();
+ printk(KERN_INFO LIRC_DRIVER_NAME
+ ": Installed.\n");
+ return 0;
+}
+
+
+static int __init lirc_sir_init(void)
+{
+ int retval;
+
+ retval = init_chrdev();
+ if (retval < 0)
+ return retval;
+ retval = init_lirc_sir();
+ if (retval) {
+ drop_chrdev();
+ return retval;
+ }
+ return 0;
+}
+
+static void __exit lirc_sir_exit(void)
+{
+ drop_hardware();
+ drop_chrdev();
+ drop_port();
+ printk(KERN_INFO LIRC_DRIVER_NAME ": Uninstalled.\n");
+}
+
+module_init(lirc_sir_init);
+module_exit(lirc_sir_exit);
+
+#ifdef LIRC_SIR_TEKRAM
+MODULE_DESCRIPTION("Infrared receiver driver for Tekram Irmate 210");
+MODULE_AUTHOR("Christoph Bartelmus");
+#elif defined(LIRC_ON_SA1100)
+MODULE_DESCRIPTION("LIRC driver for StrongARM SA1100 embedded microprocessor");
+MODULE_AUTHOR("Christoph Bartelmus");
+#elif defined(LIRC_SIR_ACTISYS_ACT200L)
+MODULE_DESCRIPTION("LIRC driver for Actisys Act200L");
+MODULE_AUTHOR("Karl Bongers");
+#elif defined(LIRC_SIR_ACTISYS_ACT220L)
+MODULE_DESCRIPTION("LIRC driver for Actisys Act220L(+)");
+MODULE_AUTHOR("Jan Roemisch");
+#else
+MODULE_DESCRIPTION("Infrared receiver driver for SIR type serial ports");
+MODULE_AUTHOR("Milan Pikula");
+#endif
+MODULE_LICENSE("GPL");
+
+#ifdef LIRC_ON_SA1100
+module_param(irq, int, S_IRUGO);
+MODULE_PARM_DESC(irq, "Interrupt (16)");
+#else
+module_param(io, int, S_IRUGO);
+MODULE_PARM_DESC(io, "I/O address base (0x3f8 or 0x2f8)");
+
+module_param(irq, int, S_IRUGO);
+MODULE_PARM_DESC(irq, "Interrupt (4 or 3)");
+
+module_param(threshold, int, S_IRUGO);
+MODULE_PARM_DESC(threshold, "space detection threshold (3)");
+#endif
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Enable debugging messages");
--
1.7.1.1
--
Jarod Wilson
jarod@xxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
