>From d2842ba67e142e78b2554cebb01341c76b84b693 Mon Sep 17 00:00:00 2001 From: Hemanth V <hemanthv@xxxxxx> Date: Fri, 30 Apr 2010 11:55:10 +0530 Subject: [PATCH] CMA3000 Accelerometer Driver This patch adds support for CMA3000 Tri-axis accelerometer, which supports Motion detect, Measurement and Free fall modes. CMA3000 supports both I2C/SPI bus for communication, currently the driver supports I2C based communication. Driver reports acceleration data through input subsystem and supports sysfs for configuration changes. This chip is currently used with OMAP4 based boards Thanks to Ossi Kauppinen <Ossi.Kauppinen@xxxxxx> for the support provided during development Signed-off-by: Hemanth V <hemanthv@xxxxxx> --- drivers/input/misc/Kconfig | 9 + drivers/input/misc/Makefile | 1 + drivers/input/misc/cma3000_d0x.c | 627 ++++++++++++++++++++++++++++++++++ drivers/input/misc/cma3000_d0x.h | 46 +++ drivers/input/misc/cma3000_d0x_i2c.c | 136 ++++++++ include/linux/i2c/cma3000.h | 60 ++++ 6 files changed, 879 insertions(+), 0 deletions(-) create mode 100644 drivers/input/misc/cma3000_d0x.c create mode 100644 drivers/input/misc/cma3000_d0x.h create mode 100644 drivers/input/misc/cma3000_d0x_i2c.c create mode 100644 include/linux/i2c/cma3000.h diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 16ec523..4752a00 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -319,4 +319,13 @@ config INPUT_PCAP To compile this driver as a module, choose M here: the module will be called pcap_keys. +config INPUT_CMA3000_I2C + tristate "VTI CMA3000 Tri-axis accelerometer" + depends on I2C + help + Say Y here if you want to use VTI CMA3000 Accelerometer + through I2C interface. + + To compile this driver as a module, choose M here: the + module will be called cma3000_dxx endif diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index a8b8485..94d6eda 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -30,4 +30,4 @@ obj-$(CONFIG_INPUT_WINBOND_CIR) += winbond-cir.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_WM831X_ON) += wm831x-on.o obj-$(CONFIG_INPUT_YEALINK) += yealink.o - +obj-$(CONFIG_INPUT_CMA3000_I2C) += cma3000_d0x_i2c.o cma3000_d0x.o diff --git a/drivers/input/misc/cma3000_d0x.c b/drivers/input/misc/cma3000_d0x.c new file mode 100644 index 0000000..c0d0ea1 --- /dev/null +++ b/drivers/input/misc/cma3000_d0x.c @@ -0,0 +1,627 @@ +/* + * cma3000_d0x.c + * VTI CMA3000_D0x Accelerometer driver + * Supports I2C/SPI interfaces + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/input.h> +#include <linux/platform_device.h> +#include <linux/i2c/cma3000.h> + +#include "cma3000_d0x.h" + +#define CMA3000_WHOAMI 0x00 +#define CMA3000_REVID 0x01 +#define CMA3000_CTRL 0x02 +#define CMA3000_STATUS 0x03 +#define CMA3000_RSTR 0x04 +#define CMA3000_INTSTATUS 0x05 +#define CMA3000_DOUTX 0x06 +#define CMA3000_DOUTY 0x07 +#define CMA3000_DOUTZ 0x08 +#define CMA3000_MDTHR 0x09 +#define CMA3000_MDFFTMR 0x0A +#define CMA3000_FFTHR 0x0B + +#define CMA3000_RANGE2G (1 << 7) +#define CMA3000_RANGE8G (0 << 7) +#define CMA3000_MODEMASK (7 << 1) +#define CMA3000_GRANGEMASK (1 << 7) + +#define CMA3000_STATUS_PERR 1 +#define CMA3000_INTSTATUS_FFDET (1 << 2) + +/* Settling time delay in ms */ +#define CMA3000_SETDELAY 30 + +/* Delay for clearing interrupt in us */ +#define CMA3000_INTDELAY 44 + + +/* + * Bit weights in mg for each of the seven bits, + * eight bit is the sign bit + */ +static int bit_to_2g[7] = {18, 36, 71, 143, 286, 571, 1142}; +static int bit_to_8g[7] = {71, 143, 286, 571, 1142, 2286, 4571}; + +/* + * Conversion for each of the eight modes to g, depending + * on G range i.e 2G or 8G + */ + +static int *mode_to_mg[8][2] = { + {NULL, NULL }, + {bit_to_8g, bit_to_2g}, + {bit_to_8g, bit_to_2g}, + {bit_to_8g, bit_to_8g}, + {bit_to_8g, bit_to_8g}, + {bit_to_8g, bit_to_2g}, + {bit_to_8g, bit_to_2g}, + {NULL, NULL }, +}; + +static ssize_t cma3000_show_attr_mode(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + ssize_t ret = 0; + uint8_t mode; + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + + mode = cma3000_read(data, CMA3000_CTRL, "ctrl"); + ret = sprintf(buf, "%d\n", (mode & CMA3000_MODEMASK) >> 1); + return ret; +} + +static ssize_t cma3000_store_attr_mode(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + unsigned long val; + int error; + uint8_t ctrl; + + error = strict_strtoul(buf, 0, &val); + if (error) + return error; + + if (val < CMAMODE_DEFAULT || val > CMAMODE_POFF) + return -EINVAL; + + mutex_lock(&data->mutex); + val &= (CMA3000_MODEMASK >> 1); + ctrl = cma3000_read(data, CMA3000_CTRL, "ctrl"); + ctrl &= ~CMA3000_MODEMASK; + ctrl |= (val << 1); + + data->pdata.mode = val; + + disable_irq(data->client->irq); + cma3000_set(data, CMA3000_CTRL, ctrl, "ctrl"); + + /* Settling time delay required after mode change */ + msleep(CMA3000_SETDELAY); + + enable_irq(data->client->irq); + mutex_unlock(&data->mutex); + + return count; +} + +static ssize_t cma3000_show_attr_grange(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + ssize_t ret = 0; + uint8_t mode; + int g_range; + + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + + mode = cma3000_read(data, CMA3000_CTRL, "ctrl"); + g_range = (mode & CMA3000_GRANGEMASK) ? CMARANGE_2G : CMARANGE_8G; + ret = sprintf(buf, "%d\n", g_range); + + return ret; +} + +static ssize_t cma3000_store_attr_grange(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + unsigned long val; + int error, g_range, fuzz_x, fuzz_y, fuzz_z; + uint8_t ctrl; + + error = strict_strtoul(buf, 0, &val); + if (error) + return error; + + mutex_lock(&data->mutex); + ctrl = cma3000_read(data, CMA3000_CTRL, "ctrl"); + ctrl &= ~CMA3000_GRANGEMASK; + + if (val == CMARANGE_2G) { + ctrl |= CMA3000_RANGE2G; + data->pdata.g_range = CMARANGE_2G; + } else if (val == CMARANGE_8G) { + ctrl |= CMA3000_RANGE8G; + data->pdata.g_range = CMARANGE_8G; + } else { + error = -EINVAL; + goto err_op_failed; + } + + g_range = data->pdata.g_range; + fuzz_x = data->pdata.fuzz_x; + fuzz_y = data->pdata.fuzz_y; + fuzz_z = data->pdata.fuzz_z; + + disable_irq(data->client->irq); + cma3000_set(data, CMA3000_CTRL, ctrl, "ctrl"); + + input_set_abs_params(data->input_dev, ABS_X, -g_range, + g_range, fuzz_x, 0); + input_set_abs_params(data->input_dev, ABS_Y, -g_range, + g_range, fuzz_y, 0); + input_set_abs_params(data->input_dev, ABS_Z, -g_range, + g_range, fuzz_z, 0); + + enable_irq(data->client->irq); + mutex_unlock(&data->mutex); + + return count; + +err_op_failed: + mutex_unlock(&data->mutex); + return error; +} + +static ssize_t cma3000_show_attr_mdthr(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + ssize_t ret = 0; + uint8_t mode; + + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + + mode = cma3000_read(data, CMA3000_MDTHR, "mdthr"); + ret = sprintf(buf, "%d\n", mode); + + return ret; +} + +static ssize_t cma3000_store_attr_mdthr(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + unsigned long val; + int error; + + error = strict_strtoul(buf, 0, &val); + if (error) + return error; + + mutex_lock(&data->mutex); + data->pdata.mdthr = val; + + disable_irq(data->client->irq); + cma3000_set(data, CMA3000_MDTHR, val, "mdthr"); + enable_irq(data->client->irq); + mutex_unlock(&data->mutex); + + return count; +} + +static ssize_t cma3000_show_attr_mdfftmr(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + ssize_t ret = 0; + uint8_t mode; + + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + + mode = cma3000_read(data, CMA3000_MDFFTMR, "mdfftmr"); + ret = sprintf(buf, "%d\n", mode); + + return ret; +} + +static ssize_t cma3000_store_attr_mdfftmr(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + unsigned long val; + int error; + + error = strict_strtoul(buf, 0, &val); + if (error) + return error; + + mutex_lock(&data->mutex); + data->pdata.mdfftmr = val; + + disable_irq(data->client->irq); + cma3000_set(data, CMA3000_MDFFTMR, val, "mdthr"); + enable_irq(data->client->irq); + mutex_unlock(&data->mutex); + + return count; +} + +static ssize_t cma3000_show_attr_ffthr(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + ssize_t ret = 0; + uint8_t mode; + + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + + mode = cma3000_read(data, CMA3000_FFTHR, "ffthr"); + ret = sprintf(buf, "%d\n", mode); + + return ret; +} + +static ssize_t cma3000_store_attr_ffthr(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct cma3000_accl_data *data = platform_get_drvdata(pdev); + unsigned long val; + int error; + + error = strict_strtoul(buf, 0, &val); + if (error) + return error; + + mutex_lock(&data->mutex); + data->pdata.ffthr = val; + + disable_irq(data->client->irq); + cma3000_set(data, CMA3000_FFTHR, val, "mdthr"); + enable_irq(data->client->irq); + mutex_unlock(&data->mutex); + + return count; +} + +static DEVICE_ATTR(mode, S_IWUSR | S_IRUGO, + cma3000_show_attr_mode, cma3000_store_attr_mode); + +static DEVICE_ATTR(grange, S_IWUSR | S_IRUGO, + cma3000_show_attr_grange, cma3000_store_attr_grange); + +static DEVICE_ATTR(mdthr, S_IWUSR | S_IRUGO, + cma3000_show_attr_mdthr, cma3000_store_attr_mdthr); + +static DEVICE_ATTR(mdfftmr, S_IWUSR | S_IRUGO, + cma3000_show_attr_mdfftmr, cma3000_store_attr_mdfftmr); + +static DEVICE_ATTR(ffthr, S_IWUSR | S_IRUGO, + cma3000_show_attr_ffthr, cma3000_store_attr_ffthr); + + +static struct attribute *cma_attrs[] = { + &dev_attr_mode.attr, + &dev_attr_grange.attr, + &dev_attr_mdthr.attr, + &dev_attr_mdfftmr.attr, + &dev_attr_ffthr.attr, + NULL, +}; + +static struct attribute_group cma3000_attr_group = { + .attrs = cma_attrs, +}; + +static void cma3000_create_sysfs(struct cma3000_accl_data *data) +{ + int ret; + ret = sysfs_create_group(&data->client->dev.kobj, &cma3000_attr_group); + if (ret) + dev_err(&data->client->dev, + "failed to create sysfs entries\n"); + +} + +static void cma3000_remove_sysfs(struct cma3000_accl_data *data) +{ + sysfs_remove_group(&data->client->dev.kobj, &cma3000_attr_group); +} + +static void decode_mg(struct cma3000_accl_data *data, int *datax, + int *datay, int *dataz) +{ + int i, tmpx = 0, tmpy = 0, tmpz = 0; + + for (i = 0; i < 7; ++i) { + tmpx += (((*datax) & BIT(i)) >> i) * (data->bit_to_mg[i]); + tmpy += (((*datay) & BIT(i)) >> i) * (data->bit_to_mg[i]); + tmpz += (((*dataz) & BIT(i)) >> i) * (data->bit_to_mg[i]); + + } + + if ((*datax) & BIT(7)) + *datax = -tmpx; + else + *datax = tmpx; + + if ((*datay) & BIT(7)) + *datay = -tmpy; + else + *datay = tmpy; + + if ((*dataz) & BIT(7)) + *dataz = -tmpz; + else + *dataz = tmpz; +} + +static irqreturn_t cma3000_thread_irq(int irq, void *dev_id) +{ + struct cma3000_accl_data *data = dev_id; + int datax, datay, dataz; + u8 ctrl, mode, range, intr_status; + + intr_status = cma3000_read(data, CMA3000_INTSTATUS, "interrupt status"); + + /* Check if free fall is detected, report immediately */ + if (intr_status & CMA3000_INTSTATUS_FFDET) { + input_report_abs(data->input_dev, ABS_MISC, 1); + input_sync(data->input_dev); + } else { + input_report_abs(data->input_dev, ABS_MISC, 0); + } + + + /* Delay required between each read for interrupt clearing */ + datax = cma3000_read(data, CMA3000_DOUTX, "X"); + udelay(CMA3000_INTDELAY); + datay = cma3000_read(data, CMA3000_DOUTY, "Y"); + udelay(CMA3000_INTDELAY); + dataz = cma3000_read(data, CMA3000_DOUTZ, "Z"); + + ctrl = cma3000_read(data, CMA3000_CTRL, "ctrl"); + mode = (ctrl & CMA3000_MODEMASK) >> 1; + range = (ctrl & CMA3000_GRANGEMASK) >> 7; + + data->bit_to_mg = mode_to_mg[mode][range]; + + /* Interrupt not for this device */ + if (data->bit_to_mg == NULL) + return IRQ_NONE; + + /* Decode register values to milli g */ + decode_mg(data, &datax, &datay, &dataz); + + input_report_abs(data->input_dev, ABS_X, datax); + input_report_abs(data->input_dev, ABS_Y, datay); + input_report_abs(data->input_dev, ABS_Z, dataz); + input_sync(data->input_dev); + + return IRQ_HANDLED; +} + +static int cma3000_reset(struct cma3000_accl_data *data) +{ + int ret; + + /* Reset sequence */ + cma3000_set(data, CMA3000_RSTR, 0x02, "Reset"); + cma3000_set(data, CMA3000_RSTR, 0x0A, "Reset"); + cma3000_set(data, CMA3000_RSTR, 0x04, "Reset"); + + /* Settling time delay */ + mdelay(10); + + ret = cma3000_read(data, CMA3000_STATUS, "Status"); + if ((ret < 0) || (ret & CMA3000_STATUS_PERR)) { + dev_err(&data->client->dev, "Reset failed\n"); + return -EIO; + } + + return 0; +} + +int cma3000_poweron(struct cma3000_accl_data *data) +{ + uint8_t ctrl = 0, mdthr, mdfftmr, ffthr, mode; + int g_range, ret; + + g_range = data->pdata.g_range; + mode = data->pdata.mode; + mdthr = data->pdata.mdthr; + mdfftmr = data->pdata.mdfftmr; + ffthr = data->pdata.ffthr; + + if (mode < CMAMODE_DEFAULT || mode > CMAMODE_POFF) { + data->pdata.mode = CMAMODE_MOTDET; + mode = data->pdata.mode; + dev_info(&data->client->dev, + "Invalid mode specified, assuming Motion Detect\n"); + } + + if (g_range == CMARANGE_2G) { + ctrl = (mode << 1) | CMA3000_RANGE2G; + } else if (g_range == CMARANGE_8G) { + ctrl = (mode << 1) | CMA3000_RANGE8G; + } else { + dev_info(&data->client->dev, + "Invalid G range specified, assuming 8G\n"); + ctrl = (mode << 1) | CMA3000_RANGE8G; + data->pdata.g_range = CMARANGE_8G; + } + + + cma3000_set(data, CMA3000_MDTHR, mdthr, "Motion Detect Threshold"); + cma3000_set(data, CMA3000_MDFFTMR, mdfftmr, "Time register"); + cma3000_set(data, CMA3000_FFTHR, ffthr, "Free fall threshold"); + ret = cma3000_set(data, CMA3000_CTRL, ctrl, "Mode setting"); + if (ret < 0) + return -EIO; + + mdelay(CMA3000_SETDELAY); + + return 0; +} + +int cma3000_poweroff(struct cma3000_accl_data *data) +{ + int ret; + + ret = cma3000_set(data, CMA3000_CTRL, CMAMODE_POFF, "Mode setting"); + mdelay(CMA3000_SETDELAY); + + return ret; +} + +int cma3000_init(struct cma3000_accl_data *data) +{ + int ret = 0, fuzz_x, fuzz_y, fuzz_z, g_range; + uint32_t irqflags; + + if (data->client->dev.platform_data == NULL) { + dev_err(&data->client->dev, "platform data not found \n"); + goto err_op2_failed; + } + + memcpy(&(data->pdata), data->client->dev.platform_data, + sizeof(struct cma3000_platform_data)); + + ret = cma3000_reset(data); + if (ret) + goto err_op2_failed; + + ret = cma3000_read(data, CMA3000_REVID, "Revid"); + if (ret < 0) + goto err_op2_failed; + + pr_info("CMA3000 Acclerometer : Revision %x\n", ret); + + /* Bring it out of default power down state */ + ret = cma3000_poweron(data); + if (ret < 0) + goto err_op2_failed; + + fuzz_x = data->pdata.fuzz_x; + fuzz_y = data->pdata.fuzz_y; + fuzz_z = data->pdata.fuzz_z; + g_range = data->pdata.g_range; + irqflags = data->pdata.irqflags; + + data->input_dev = input_allocate_device(); + if (data->input_dev == NULL) { + ret = -ENOMEM; + dev_err(&data->client->dev, + "Failed to allocate input device\n"); + goto err_op2_failed; + } + + data->input_dev->name = "cma3000-acclerometer"; + +#ifdef CONFIG_INPUT_CMA3000_I2C + data->input_dev->id.bustype = BUS_I2C; +#endif + + __set_bit(EV_ABS, data->input_dev->evbit); + __set_bit(EV_MSC, data->input_dev->evbit); + + input_set_abs_params(data->input_dev, ABS_X, -g_range, + g_range, fuzz_x, 0); + input_set_abs_params(data->input_dev, ABS_Y, -g_range, + g_range, fuzz_y, 0); + input_set_abs_params(data->input_dev, ABS_Z, -g_range, + g_range, fuzz_z, 0); + input_set_abs_params(data->input_dev, ABS_MISC, 0, + 1, 0, 0); + + ret = input_register_device(data->input_dev); + if (ret) { + dev_err(&data->client->dev, + "Unable to register input device\n"); + goto err_op2_failed; + } + + mutex_init(&data->mutex); + + if (data->client->irq) { + ret = request_threaded_irq(data->client->irq, NULL, + cma3000_thread_irq, + irqflags | IRQF_ONESHOT, + data->client->name, data); + + if (ret < 0) { + dev_err(&data->client->dev, + "request_threaded_irq failed\n"); + goto err_op1_failed; + } + } + + cma3000_create_sysfs(data); + + return 0; + +err_op1_failed: + mutex_destroy(&data->mutex); + input_unregister_device(data->input_dev); +err_op2_failed: + if (data != NULL) { + if (data->input_dev != NULL) + input_free_device(data->input_dev); + } + + return ret; +} + +int cma3000_exit(struct cma3000_accl_data *data) +{ + int ret; + + ret = cma3000_poweroff(data); + + if (data->client->irq) + free_irq(data->client->irq, data); + + mutex_destroy(&data->mutex); + input_unregister_device(data->input_dev); + input_free_device(data->input_dev); + cma3000_remove_sysfs(data); + + return ret; +} diff --git a/drivers/input/misc/cma3000_d0x.h b/drivers/input/misc/cma3000_d0x.h new file mode 100644 index 0000000..906d29e --- /dev/null +++ b/drivers/input/misc/cma3000_d0x.h @@ -0,0 +1,46 @@ +/* + * cma3000_d0x.h + * VTI CMA3000_D0x Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef INPUT_CMA3000_H +#define INPUT_CMA3000_H + +#include <linux/i2c.h> +#include <linux/input.h> + +struct cma3000_accl_data { +#ifdef CONFIG_INPUT_CMA3000_I2C + struct i2c_client *client; +#endif + struct input_dev *input_dev; + struct cma3000_platform_data pdata; + + /* mutex for sysfs operations */ + struct mutex mutex; + int *bit_to_mg; +}; + +int cma3000_set(struct cma3000_accl_data *, u8, u8, char *); +int cma3000_read(struct cma3000_accl_data *, u8, char *); +int cma3000_init(struct cma3000_accl_data *); +int cma3000_exit(struct cma3000_accl_data *); +int cma3000_poweron(struct cma3000_accl_data *); +int cma3000_poweroff(struct cma3000_accl_data *); + +#endif diff --git a/drivers/input/misc/cma3000_d0x_i2c.c b/drivers/input/misc/cma3000_d0x_i2c.c new file mode 100644 index 0000000..d2ad638 --- /dev/null +++ b/drivers/input/misc/cma3000_d0x_i2c.c @@ -0,0 +1,136 @@ +/* + * cma3000_d0x_i2c.c + * + * Implements I2C interface for VTI CMA300_D0x Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/i2c/cma3000.h> +#include "cma3000_d0x.h" + +int cma3000_set(struct cma3000_accl_data *accl, u8 reg, u8 val, char *msg) +{ + int ret = i2c_smbus_write_byte_data(accl->client, reg, val); + if (ret < 0) + dev_err(&accl->client->dev, + "i2c_smbus_write_byte_data failed (%s)\n", msg); + return ret; +} + +int cma3000_read(struct cma3000_accl_data *accl, u8 reg, char *msg) +{ + int ret = i2c_smbus_read_byte_data(accl->client, reg); + if (ret < 0) + dev_err(&accl->client->dev, + "i2c_smbus_read_byte_data failed (%s)\n", msg); + return ret; +} + +static int __devinit cma3000_accl_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct cma3000_accl_data *data = NULL; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (data == NULL) { + ret = -ENOMEM; + goto err_op_failed; + } + + data->client = client; + i2c_set_clientdata(client, data); + + ret = cma3000_init(data); + if (ret) + goto err_op_failed; + + return 0; + +err_op_failed: + + if (data != NULL) + kfree(data); + + return ret; +} + +static int __devexit cma3000_accl_remove(struct i2c_client *client) +{ + struct cma3000_accl_data *data = i2c_get_clientdata(client); + int ret; + + ret = cma3000_exit(data); + i2c_set_clientdata(client, NULL); + kfree(data); + + return ret; +} + +#ifdef CONFIG_PM +static int cma3000_accl_suspend(struct i2c_client *client, pm_message_t mesg) +{ + struct cma3000_accl_data *data = i2c_get_clientdata(client); + + return cma3000_poweroff(data); +} + +static int cma3000_accl_resume(struct i2c_client *client) +{ + struct cma3000_accl_data *data = i2c_get_clientdata(client); + + return cma3000_poweron(data); +} +#endif + +static const struct i2c_device_id cma3000_id[] = { + { "cma3000_accl", 0 }, + { }, +}; + +static struct i2c_driver cma3000_accl_driver = { + .probe = cma3000_accl_probe, + .remove = cma3000_accl_remove, + .id_table = cma3000_id, +#ifdef CONFIG_PM + .suspend = cma3000_accl_suspend, + .resume = cma3000_accl_resume, +#endif + .driver = { + .name = "cma3000_accl" + }, +}; + +static int __init cma3000_accl_init(void) +{ + + return i2c_add_driver(&cma3000_accl_driver); +} + +static void __exit cma3000_accl_exit(void) +{ + i2c_del_driver(&cma3000_accl_driver); +} + +module_init(cma3000_accl_init); +module_exit(cma3000_accl_exit); + +MODULE_DESCRIPTION("CMA3000-D0x Accelerometer Driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Hemanth V <hemanthv@xxxxxx>"); diff --git a/include/linux/i2c/cma3000.h b/include/linux/i2c/cma3000.h new file mode 100644 index 0000000..50aa3fc --- /dev/null +++ b/include/linux/i2c/cma3000.h @@ -0,0 +1,60 @@ +/* + * cma3000.h + * VTI CMA300_Dxx Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef _LINUX_CMA3000_I2C_H +#define _LINUX_CMA3000_I2C_H + +#define CMAMODE_DEFAULT 0 +#define CMAMODE_MEAS100 1 +#define CMAMODE_MEAS400 2 +#define CMAMODE_MEAS40 3 +#define CMAMODE_MOTDET 4 +#define CMAMODE_FF100 5 +#define CMAMODE_FF400 6 +#define CMAMODE_POFF 7 + +#define CMARANGE_2G 2000 +#define CMARANGE_8G 8000 + +/** + * struct cma3000_i2c_platform_data - CMA3000 Platform data + * @fuzz_x: Noise on X Axis + * @fuzz_y: Noise on Y Axis + * @fuzz_z: Noise on Z Axis + * @g_range: G range in milli g i.e 2000 or 8000 + * @mode: Operating mode + * @mdthr: Motion detect threshold value + * @mdfftmr: Motion detect and free fall time value + * @ffthr: Free fall threshold value + */ + +struct cma3000_platform_data { + int fuzz_x; + int fuzz_y; + int fuzz_z; + int g_range; + uint8_t mode; + uint8_t mdthr; + uint8_t mdfftmr; + uint8_t ffthr; + uint32_t irqflags; +}; + +#endif -- 1.5.6.3 -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
