Op 15-10-09 20:13, Dmitry Torokhov schreef:
It lokks like the keyboard controller switched from translated to
non-translated mode: '1c' is make code and 'f0 1c' is break (aka
release) code.
Could you tell me how the keyboard indentified (in dmesg) after fresh
boot and after you do the bind/unbind trick on the older kernel?
What do you mean by "how the keyboard indentified"? Are you asking for
the debug trace in dmesg? I have the beginning of a boot with the debug
trace to see after a fresh boot. I don't have dmesg history with
i8042.debug of the bind/unbind trick, so I'll reboot in an old kernel
and do it again (but I cannot do this before tuesday, when i have
physical access to the machine).
sftp://piel@localhost:2226/home/piel/busy/i8042-begin-boot-keyboard.dmesg
BTW, do you have i8042.reset parameyer on your command line? What
happens if you remove it?
The two logs where done with i8042.reset. However, without this
parameter, the behaviour is identical: the keyboard needs the
unbind/bind trick after the first resume.
Eric
Linux version 2.6.32-rc3-git-eric-00343-g35578ca (piel@dutifh) (gcc version 4.4.1 (GCC) ) #17 SMP PREEMPT Mon Oct 12 18:54:14 CEST 2009
Command line: BOOT_IMAGE=2632-rc3-git-eric-00343-g35578c root=UUID=01dc5fcc-55d3-4bae-932b-1119dbe7ff0b resume=UUID=0d777318-dc2d-4ec3-aa25-fbad7e0fa039 splash=silent i8042.debug i8042.reset vga=791
KERNEL supported cpus:
Intel GenuineIntel
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f7b0000 (usable)
BIOS-e820: 000000007f7b0000 - 000000007f7c5400 (reserved)
BIOS-e820: 000000007f7c5400 - 000000007f7e7fb8 (ACPI NVS)
BIOS-e820: 000000007f7e7fb8 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed9a000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI 2.4 present.
last_pfn = 0x7f7b0 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-D3FFF write-protect
D4000-EFFFF uncachable
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07F800000 mask FFF800000 uncachable
2 base 0FEDA0000 mask FFFFE0000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2040MB, range: 8MB, type UC
reg 2, base: 4175488KB, range: 128KB, type UC
total RAM coverred: 2040M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 16M num_reg: 2 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2040MB, range: 8MB, type UC
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-000000007f7b0000
0000000000 - 007f600000 page 2M
007f600000 - 007f7b0000 page 4k
kernel direct mapping tables up to 7f7b0000 @ 8000-c000
RAMDISK: 37666000 - 37fefab0
ACPI: RSDP 00000000000f7980 00024 (v02 HP )
ACPI: XSDT 000000007f7c81c4 00074 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
ACPI: FACP 000000007f7c8084 000F4 (v04 HP 30C9 00000003 HP 00000001)
ACPI: DSDT 000000007f7c84c0 13484 (v01 HP nc2500 00010000 MSFT 03000001)
ACPI: FACS 000000007f7e7d80 00040
ACPI: SLIC 000000007f7c8238 00176 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
ACPI: HPET 000000007f7c83b0 00038 (v01 HP 30C9 00000001 HP 00000001)
ACPI: APIC 000000007f7c83e8 00068 (v01 HP 30C9 00000001 HP 00000001)
ACPI: MCFG 000000007f7c8450 0003C (v01 HP 30C9 00000001 HP 00000001)
ACPI: TCPA 000000007f7c848c 00032 (v02 HP 30C9 00000001 HP 00000001)
ACPI: SSDT 000000007f7db944 002BE (v01 HP HPQPAT 00000001 MSFT 03000001)
ACPI: SSDT 000000007f7dc586 0025F (v01 HP Cpu0Tst 00003000 INTL 20060317)
ACPI: SSDT 000000007f7dc7e5 000A6 (v01 HP Cpu1Tst 00003000 INTL 20060317)
ACPI: SSDT 000000007f7dc88b 004D7 (v01 HP CpuPm 00003000 INTL 20060317)
ACPI: Local APIC address 0xfee00000
(7 early reservations) ==> bootmem [0000000000 - 007f7b0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 00019daa64] TEXT DATA BSS ==> [0001000000 - 00019daa64]
#3 [0037666000 - 0037fefab0] RAMDISK ==> [0037666000 - 0037fefab0]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [00019db000 - 00019db18c] BRK ==> [00019db000 - 00019db18c]
#6 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0007f7b0
On node 0 totalpages: 522063
DMA zone: 56 pages used for memmap
DMA zone: 101 pages reserved
DMA zone: 3842 pages, LIFO batch:0
DMA32 zone: 7083 pages used for memmap
DMA32 zone: 510981 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
Booting paravirtualized kernel on bare hardware
NR_CPUS:4096 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff880001a00000 s85400 r8192 d21096 u1048576
pcpu-alloc: s85400 r8192 d21096 u1048576 alloc=1*2097152
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514823
Kernel command line: BOOT_IMAGE=2632-rc3-git-eric-00343-g35578c root=UUID=01dc5fcc-55d3-4bae-932b-1119dbe7ff0b resume=UUID=0d777318-dc2d-4ec3-aa25-fbad7e0fa039 splash=silent i8042.debug i8042.reset vga=791
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Initializing CPU#0
Memory: 2035536k/2088640k available (4036k kernel code, 388k absent, 51984k reserved, 4576k data, 552k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Experimental preemptable hierarchical RCU implementation.
NR_IRQS:33024 nr_irqs:424
Extended CMOS year: 2000
Console: colour dummy device 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 1196.971 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 2393.94 BogoMIPS (lpj=1196971)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring handled by SMI
using mwait in idle threads.
Performance Events: Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
ACPI: Core revision 20090903
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU U7600 @ 1.20GHz stepping 0d
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2393.89 BogoMIPS (lpj=1196949)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 Duo CPU U7600 @ 1.20GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (4787.84 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
PCI: MCFG area at f8000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at f8000000 - fbffffff
ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [C29F] (on)
ACPI: Power Resource [C1C7] (off)
ACPI: Power Resource [C3AD] (off)
ACPI: Power Resource [C3B0] (off)
ACPI: Power Resource [C3C3] (off)
ACPI: Power Resource [C3C4] (off)
ACPI: Power Resource [C3C5] (off)
ACPI: Power Resource [C3C6] (off)
ACPI: Power Resource [C3C7] (off)
ACPI: No dock devices found.
ACPI: PCI Root Bridge [C003] (0000:00)
pci 0000:00:02.0: reg 10 64bit mmio: [0xe0400000-0xe04fffff]
pci 0000:00:02.0: reg 18 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 20 io port: [0x2000-0x2007]
pci 0000:00:02.1: reg 10 64bit mmio: [0xe0500000-0xe05fffff]
pci 0000:00:19.0: reg 10 32bit mmio: [0xe0600000-0xe061ffff]
pci 0000:00:19.0: reg 14 32bit mmio: [0xe0620000-0xe0620fff]
pci 0000:00:19.0: reg 18 io port: [0x2020-0x203f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x2040-0x205f]
pci 0000:00:1a.1: reg 20 io port: [0x2060-0x207f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xe0621000-0xe06213ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xe0624000-0xe0627fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f]
pci 0000:00:1d.1: reg 20 io port: [0x20a0-0x20bf]
pci 0000:00:1d.2: reg 20 io port: [0x20c0-0x20df]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xe0628000-0xe06283ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0500 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 02e8 (mask 0007)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x20e0-0x20ef]
pci 0000:10:00.0: reg 10 64bit mmio: [0xe0000000-0xe0003fff]
pci 0000:10:00.0: supports D1 D2
pci 0000:00:1c.1: bridge 32bit mmio: [0xe0000000-0xe00fffff]
pci 0000:02:06.0: reg 10 32bit mmio: [0xe0100000-0xe0100fff]
pci 0000:02:06.0: supports D1 D2
pci 0000:02:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:06.0: PME# disabled
pci 0000:02:06.1: reg 10 32bit mmio: [0xe0101000-0xe01017ff]
pci 0000:02:06.1: supports D1 D2
pci 0000:02:06.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:06.1: PME# disabled
pci 0000:02:06.2: reg 10 32bit mmio: [0xe0102000-0xe01020ff]
pci 0000:02:06.2: supports D1 D2
pci 0000:02:06.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:06.2: PME# disabled
pci 0000:02:06.3: reg 10 32bit mmio: [0xe0103000-0xe01030ff]
pci 0000:02:06.3: supports D1 D2
pci 0000:02:06.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:06.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xe0100000-0xe03fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.C003._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C003.C0B2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C003.C11F._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C003.C133._PRT]
ACPI: PCI Interrupt Link [C12F] (IRQs *10 11)
ACPI: PCI Interrupt Link [C130] (IRQs *10 11)
ACPI: PCI Interrupt Link [C131] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C132] (IRQs 10 11) *5
ACPI: PCI Interrupt Link [C142] (IRQs *10 11)
ACPI: PCI Interrupt Link [C143] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C144] (IRQs 10 *11)
ACPI Exception: AE_NOT_FOUND, Evaluating _PRS (20090903/pci_link-184)
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
alloc irq_desc for 23 on node -1
alloc kstat_irqs on node -1
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xe0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x7f7fffff could not be reserved
system 00:0a: ioport range 0x500-0x55f has been reserved
system 00:0a: ioport range 0x800-0x80f has been reserved
system 00:0a: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:0a: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0c: ioport range 0x4d0-0x4d1 has been reserved
system 00:0c: ioport range 0x2f8-0x2ff has been reserved
system 00:0c: ioport range 0x3f8-0x3ff has been reserved
system 00:0c: ioport range 0x1000-0x107f has been reserved
system 00:0c: ioport range 0x1100-0x113f has been reserved
system 00:0c: ioport range 0x1200-0x121f has been reserved
system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec000ff could not be reserved
system 00:0c: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:0c: iomem range 0xfed45000-0xfed8ffff has been reserved
system 00:0c: iomem range 0xfed90000-0xfed99fff has been reserved
system 00:0d: iomem range 0xcee00-0xcffff has been reserved
system 00:0d: iomem range 0xd2000-0xd3fff has been reserved
system 00:0d: iomem range 0xfeda0000-0xfedbffff has been reserved
system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: disabled
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:10
pci 0000:00:1c.1: IO window: disabled
pci 0000:00:1c.1: MEM window: 0xe0000000-0xe00fffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:02:06.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:06.0: IO window: 0x003000-0x0030ff
pci 0000:02:06.0: IO window: 0x003400-0x0034ff
pci 0000:02:06.0: PREFETCH window: 0x80000000-0x83ffffff
pci 0000:02:06.0: MEM window: 0x84000000-0x87ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0x3000-0x3fff
pci 0000:00:1e.0: MEM window: 0xe0100000-0xe03fffff
pci 0000:00:1e.0: PREFETCH window: 0x80000000-0x83ffffff
alloc irq_desc for 16 on node -1
alloc kstat_irqs on node -1
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 17 on node -1
alloc kstat_irqs on node -1
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
alloc irq_desc for 18 on node -1
alloc kstat_irqs on node -1
pci 0000:02:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:10: resource 1 mem: [0xe0000000-0xe00fffff]
pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:02: resource 1 mem: [0xe0100000-0xe03fffff]
pci_bus 0000:02: resource 2 pref mem [0x80000000-0x83ffffff]
pci_bus 0000:02: resource 3 io: [0x00-0xffff]
pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:03: resource 0 io: [0x3000-0x30ff]
pci_bus 0000:03: resource 1 io: [0x3400-0x34ff]
pci_bus 0000:03: resource 2 pref mem [0x80000000-0x83ffffff]
pci_bus 0000:03: resource 3 mem: [0x84000000-0x87ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 9766k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1255634791.705:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 3996
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
alloc irq_desc for 24 on node -1
alloc kstat_irqs on node -1
pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 25 on node -1
alloc kstat_irqs on node -1
pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90004100000, using 3072k, total 7616k
vesafb: mode is 1024x768x16, linelength=2048, pages=3
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 965GM Chipset
agpgart-intel 0000:00:00.0: detected 7676K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
brd: module loaded
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: quirky BIOS, skipping spindown on poweroff and hibernation
ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x20e0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x20e8 irq 15
ata2: port disabled. ignoring.
PNP: PS/2 Controller [PNP0303:C29C,PNP0f13:C29D] at 0x60,0x64 irq 1,12
drivers/input/serio/i8042.c: aa -> i8042 (command) [1]
drivers/input/serio/i8042.c: 55 <- i8042 (return) [1]
drivers/input/serio/i8042.c: 20 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 30 <- i8042 (return) [1]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [1]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 5a -> i8042 (parameter) [1]
drivers/input/serio/i8042.c: 5a <- i8042 (return) [1]
drivers/input/serio/i8042.c: a7 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 20 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 30 <- i8042 (return) [2]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 20 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 10 <- i8042 (return) [2]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
drivers/input/serio/i8042.c: f0 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: f0 <- i8042 (return) [2]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 56 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: 56 <- i8042 (return) [2]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
drivers/input/serio/i8042.c: a4 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: 11 <- i8042 (return) [3]
i8042.c: Detected active multiplexing controller, rev 1.1.
drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [3]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [3]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 91 -> i8042 (command) [3]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 92 -> i8042 (command) [3]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [3]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 12 -> i8042 (parameter) [3]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [4]
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
Driver 'rtc_cmos' needs updating - please use bus_type methods
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
ata1.00: ATA-7: TOSHIBA MK8009GAH, BS021C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.01: ATAPI: HL-DT-ST DVDRAM GSA-U10N, HP06, max MWDMA2
ata1.00: configured for UDMA/100
ata1.01: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK8009GA BS02 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
scsi 0:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N HP06 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
registered taskstats version 1
rtc_cmos 00:06: setting system clock to 2009-10-15 19:26:32 UTC (1255634792)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 552k freed
Write protecting the kernel read-only data: 5604k
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
ACPI: Sleep Button [C2BF]
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [C155]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
alloc irq_desc for 26 on node -1
alloc kstat_irqs on node -1
i915 0000:00:02.0: irq 26 for MSI/MSI-X
[drm] set up 7M of stolen space
[drm] TV-14: set mode NTSC 480i 0
fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
Console: switching to colour dummy device 80x25
Console: switching to colour frame buffer device 160x50
[drm] DAC-6: set mode 1920x1200 2a
[drm] LVDS-8: set mode 1280x800 2b
fb0: inteldrmfb frame buffer device
registered panic notifier
acpi device:00: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
ACPI: Video Device [C09A] (multi-head: yes rom: no post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
drivers/input/serio/i8042.c: f2 -> i8042 (kbd-data) [2206]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2206]
drivers/input/serio/i8042.c: ab <- i8042 (interrupt, 0, 1) [2209]
drivers/input/serio/i8042.c: 83 <- i8042 (interrupt, 0, 1) [2212]
drivers/input/serio/i8042.c: f4 -> i8042 (kbd-data) [2212]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2215]
input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
drivers/input/serio/i8042.c: 90 -> i8042 (command) [2215]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2215]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [2218]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [2219]
drivers/input/serio/i8042.c: 91 -> i8042 (command) [2219]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2219]
drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [2219]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [2219]
drivers/input/serio/i8042.c: 91 -> i8042 (command) [2219]
drivers/input/serio/i8042.c: ed -> i8042 (parameter) [2219]
drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [2220]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [2220]
drivers/input/serio/i8042.c: 92 -> i8042 (command) [2220]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2220]
drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [2221]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [2221]
drivers/input/serio/i8042.c: 92 -> i8042 (command) [2221]
drivers/input/serio/i8042.c: ed -> i8042 (parameter) [2221]
drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [2222]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [2222]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [2222]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2222]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [2225]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [2226]
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0621000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
alloc irq_desc for 20 on node -1
alloc kstat_irqs on node -1
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe0628000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
b43-pci-bridge 0000:10:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
b43-pci-bridge 0000:10:00.0: setting latency timer to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:10:00.0
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00002040
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 17, io base 0x00002060
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002080
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
alloc irq_desc for 22 on node -1
alloc kstat_irqs on node -1
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 22, io base 0x000020a0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000020c0
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
usb 2-6: new high speed USB device using ehci_hcd and address 3
usb 2-6: configuration #1 chosen from 1 choice
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 2 ports detected
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 5-2: new full speed USB device using uhci_hcd and address 2
usb 5-2: configuration #1 chosen from 1 choice
usb 2-6.1: new high speed USB device using ehci_hcd and address 4
usb 2-6.1: configuration #1 chosen from 1 choice
hub 2-6.1:1.0: USB hub found
hub 2-6.1:1.0: 4 ports detected
usb 2-6.2: new low speed USB device using ehci_hcd and address 5
usb 2-6.2: configuration #1 chosen from 1 choice
input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6.2/2-6.2:1.0/input/input5
generic-usb 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.7-6.2/input0
usb 2-6.1.1: new high speed USB device using ehci_hcd and address 6
usb 2-6.1.1: configuration #1 chosen from 1 choice
usb 2-6.1.2: new low speed USB device using ehci_hcd and address 7
usb 2-6.1.2: configuration #1 chosen from 1 choice
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6.1/2-6.1.2/2-6.1.2:1.0/input/input6
generic-usb 0003:046D:C018.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.7-6.1.2/input0
usb 2-6: USB disconnect, address 3
usb 2-6.1: USB disconnect, address 4
usb 2-6.1.1: USB disconnect, address 6
usb 2-6.1.2: USB disconnect, address 7
usb 2-6.2: USB disconnect, address 5
udev: starting version 146
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 0:0:1:0: Attached scsi generic sg1 type 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: AC Adapter [C23B] (on-line)
ACPI: Battery Slot [C23D] (battery present)
lis3lv02d: hardware type NC2510 found.
lis3lv02d: 12 bits sensor found
input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input7
Registered led device: hp::hddprotect
lis3lv02d driver loaded.
cfg80211: Calling CRDA to update world regulatory domain
input: PC Speaker as /devices/platform/pcspkr/input/input8
ACPI: WMI: Mapper loaded
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ6] (25 C)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [TZ0] (68 C)
thermal LNXTHERM:03: registered as thermal_zone2
ACPI: Thermal Zone [TZ1] (69 C)
thermal LNXTHERM:04: registered as thermal_zone3
ACPI: Thermal Zone [TZ3] (54 C)
thermal LNXTHERM:05: registered as thermal_zone4
ACPI: Thermal Zone [TZ4] (29 C)
thermal LNXTHERM:06: registered as thermal_zone5
ACPI: Thermal Zone [TZ5] (30 C)
alloc irq_desc for 19 on node -1
alloc kstat_irqs on node -1
ohci1394 0000:02:06.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0101000-e01017ff] Max Packet=[2048] IR/IT contexts=[4/4]
ACPI: SSDT 000000007f7dbcca 0023D (v01 HP Cpu0Ist 00003000 INTL 20060317)
ACPI: SSDT 000000007f7dbf8c 005FA (v01 HP Cpu0Cst 00003001 INTL 20060317)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Marking TSC unstable due to TSC halts in idle
Switching to clocksource hpet
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 000000007f7dbc02 000C8 (v01 HP Cpu1Ist 00003000 INTL 20060317)
ACPI: SSDT 000000007f7dbf07 00085 (v01 HP Cpu1Cst 00003000 INTL 20060317)
processor LNXCPU:01: registered as cooling_device2
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
ricoh-mmc: Ricoh MMC controller found at 0000:02:06.3 [1180:0843] (rev 11)
ricoh-mmc: Controller is now disabled.
yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30c9]
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
e1000e 0000:00:19.0: setting latency timer to 64
alloc irq_desc for 27 on node -1
alloc kstat_irqs on node -1
e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34491]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [34491]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34494]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34495]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34495]
drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34495]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34498]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34498]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34498]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34500]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34500]
drivers/input/serio/i8042.c: 0a -> i8042 (parameter) [34500]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34503]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34503]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34503]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34506]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34506]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34506]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34509]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34509]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34509]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34511]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34511]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34512]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34514]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34514]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34514]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34517]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34517]
drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [34517]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34520]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34520]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34520]
tpm_inf_pnp 00:02: Found C284 with ID IFX0102
tpm_inf_pnp 00:02: TPM found: config base 0x560, data base 0x570, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34526]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34526]
drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [34526]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34529]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34529]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34529]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34531]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34531]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34532]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34534]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34534]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34534]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34537]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34537]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34537]
yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0cb8, PCI irq 18
yenta_cardbus 0000:02:06.0: Socket status: 30000006
pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe03fffff
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0x80000000 - 0x83ffffff
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34540]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34540]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34540]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34543]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34543]
drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [34543]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34546]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34546]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34546]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34548]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34548]
drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [34549]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34551]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34551]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34551]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34554]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34554]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34554]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34557]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34557]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34557]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34560]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34560]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34560]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34562]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34569]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [34569]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34571]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34572]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34572]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34572]
b43-phy0: Broadcom 4311 WLAN found (core revision 13)
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34575]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34575]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34575]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34578]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34578]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34578]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34581]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34581]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34581]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34584]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34584]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34584]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34587]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34587]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34587]
b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 9
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34590]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34590]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34590]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34592]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34592]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34592]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34595]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34595]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34595]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34598]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34599]
drivers/input/serio/i8042.c: 46 <- i8042 (interrupt, 2, 12) [34601]
drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 2, 12) [34603]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34603]
drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34603]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34606]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34606]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34606]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34609]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34609]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [34609]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34612]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34612]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34612]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34614]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34615]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34615]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34617]
fan PNP0C0B:00: registered as cooling_device3
ACPI: Fan [C3B1] (off)
fan PNP0C0B:01: registered as cooling_device4
ACPI: Fan [C3B2] (off)
fan PNP0C0B:02: registered as cooling_device5
ACPI: Fan [C3C8] (off)
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34619]
fan PNP0C0B:03: registered as cooling_device6
ACPI: Fan [C3C9] (off)
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34619]
fan PNP0C0B:04: registered as cooling_device7
ACPI: Fan [C3CA] (off)
fan PNP0C0B:05: registered as cooling_device8
ACPI: Fan [C3CB] (off)
fan PNP0C0B:06: registered as cooling_device9
ACPI: Fan [C3CC] (off)
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34622]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34622]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34622]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34625]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34625]
drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 2, 12) [34627]
drivers/input/serio/i8042.c: 64 <- i8042 (interrupt, 2, 12) [34630]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34630]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34630]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34633]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34633]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34633]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34635]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34635]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34635]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34638]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34638]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34638]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34641]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34641]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34641]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34644]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34644]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34644]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34647]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34648]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34649]
drivers/input/serio/i8042.c: 64 <- i8042 (interrupt, 2, 12) [34652]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34652]
drivers/input/serio/i8042.c: e1 -> i8042 (parameter) [34652]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 2, 12) [34655]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34655]
drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34655]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34657]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34657]
drivers/input/serio/i8042.c: ff -> i8042 (parameter) [34657]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34660]
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1b:24:ae:b7:02
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 6, PHY: 6, PBA No: ffffff-0ff
udev: renamed network interface eth0 to eth1
phy0: Selected rate control algorithm 'pid'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 2, 12) [34991]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34993]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34993]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34993]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34996]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34996]
drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [34996]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34999]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [34999]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34999]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35002]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35002]
drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35002]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35005]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35005]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35005]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35008]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35008]
drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35008]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35010]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35010]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35010]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35013]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35015]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35015]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35015]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35017]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35017]
drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35017]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35020]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35020]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35020]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35023]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35023]
drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35023]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35026]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35026]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35026]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35029]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35029]
drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35029]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35031]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35031]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35031]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35034]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35035]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35035]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35035]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35038]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35038]
drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35038]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35041]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35041]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35041]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35044]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35044]
drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35044]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35047]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35047]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35047]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35050]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35050]
drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35050]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35053]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35053]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35053]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35055]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35057]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35057]
drivers/input/serio/i8042.c: ff -> i8042 (parameter) [35057]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35060]
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001b249929bd0f10]
drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 2, 12) [35393]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35395]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35395]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35395]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35398]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35398]
drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35398]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35400]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35400]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35400]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35403]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35403]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [35403]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35406]
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35406]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35406]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35409]
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input9
drivers/input/serio/i8042.c: 90 -> i8042 (command) [35409]
drivers/input/serio/i8042.c: f4 -> i8042 (parameter) [35409]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35411]
drivers/input/serio/i8042.c: 91 -> i8042 (command) [35412]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35412]
drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [35412]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [35412]
drivers/input/serio/i8042.c: 92 -> i8042 (command) [35412]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35412]
drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [35413]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [35413]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35413]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35413]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35416]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35417]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35418]
drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [35418]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35420]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35421]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35421]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35423]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35423]
drivers/input/serio/i8042.c: 0a -> i8042 (parameter) [35423]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35427]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35427]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35427]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35430]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35430]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35430]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35433]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35433]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35433]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35435]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35435]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35435]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35439]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35439]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35439]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35442]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35442]
drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [35442]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35445]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35445]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35445]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35448]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35448]
drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [35448]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35450]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35451]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35451]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35453]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35453]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35453]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35456]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35456]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35456]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35459]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35459]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35459]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35462]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35462]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35462]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35465]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35465]
drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [35465]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35468]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35468]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35468]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35471]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35471]
drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [35471]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35474]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35474]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35474]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35478]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35478]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35478]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35480]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35481]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35481]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35483]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35483]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35483]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35486]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35486]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35486]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35489]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35491]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35491]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35491]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35494]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35494]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35494]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35497]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35497]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35497]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35500]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35500]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35500]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35503]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35503]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35503]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35506]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35507]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35507]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35510]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35510]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35510]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35513]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35513]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35513]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35516]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35516]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35516]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35519]
drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 5, 12) [35520]
drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [35523]
drivers/input/serio/i8042.c: 16 <- i8042 (interrupt, 5, 12) [35526]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35526]
drivers/input/serio/i8042.c: ff -> i8042 (parameter) [35526]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35532]
sdhci-pci 0000:02:06.2: SDHCI controller found [1180:0822] (rev 21)
sdhci-pci 0000:02:06.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:02:06.2] using PIO
HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 5, 12) [35894]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35897]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35897]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35897]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35900]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35900]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35900]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35903]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35903]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35903]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35906]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35906]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35906]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35909]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35909]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35909]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35912]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35912]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35912]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35915]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35915]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35915]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35918]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35918]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35918]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35921]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35921]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35921]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35924]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35924]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35924]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35927]
drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 5, 12) [35928]
drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [35930]
drivers/input/serio/i8042.c: 16 <- i8042 (interrupt, 5, 12) [35933]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35933]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35933]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35936]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35936]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35936]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35939]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35939]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35939]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35942]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35942]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35942]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35945]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35945]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35945]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35948]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35948]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35948]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35951]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35951]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35951]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35954]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35954]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35954]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35957]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35957]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [35957]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35960]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35960]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35960]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35963]
drivers/input/serio/i8042.c: 01 <- i8042 (interrupt, 5, 12) [35964]
drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [35967]
drivers/input/serio/i8042.c: b1 <- i8042 (interrupt, 5, 12) [35970]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35970]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35970]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35973]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35973]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35973]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35976]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35976]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35976]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35979]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35979]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35979]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35982]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35982]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35982]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35985]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35985]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35985]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35988]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35988]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35988]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35991]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35991]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35991]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35994]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35994]
drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [35994]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35997]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [35997]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35997]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36000]
drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [36001]
drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [36004]
drivers/input/serio/i8042.c: 13 <- i8042 (interrupt, 5, 12) [36007]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36007]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36007]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36010]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36010]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36010]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36013]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36013]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36013]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36016]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36016]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36016]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36019]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36019]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36019]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36022]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36022]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36022]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36025]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36025]
drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36025]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36028]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36028]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36028]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36031]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36031]
drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36031]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36034]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36034]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [36034]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36037]
drivers/input/serio/i8042.c: 20 <- i8042 (interrupt, 5, 12) [36039]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [36042]
drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [36045]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36045]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36045]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36048]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36048]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36048]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36051]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36051]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36051]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36054]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36054]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36054]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36056]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36056]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36056]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36059]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36059]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36059]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36062]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36062]
drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36062]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36065]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36065]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36065]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36068]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36068]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36068]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36071]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36071]
drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [36071]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36074]
drivers/input/serio/i8042.c: 4a <- i8042 (interrupt, 5, 12) [36076]
drivers/input/serio/i8042.c: 80 <- i8042 (interrupt, 5, 12) [36079]
drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [36082]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36082]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36082]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36085]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36085]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36085]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36088]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36088]
drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36088]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36091]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36091]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36091]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36094]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36094]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36094]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36096]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36096]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36097]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36099]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36099]
drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36100]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36102]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36102]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36102]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36105]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36105]
drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36105]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36108]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36108]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [36108]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36111]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36111]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [36111]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36114]
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36114]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36114]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36117]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36117]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36117]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36120]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36120]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [36120]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36123]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36123]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36123]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36126]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36126]
drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36126]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36129]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36129]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36129]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36132]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36132]
drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36132]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36135]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36135]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36135]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36138]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36138]
drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36138]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36141]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36141]
drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [36141]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36144]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36144]
drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [36144]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36147]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36147]
drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36147]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36150]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36150]
drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [36150]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36153]
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36153]
drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36153]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36156]
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input11
drivers/input/serio/i8042.c: 93 -> i8042 (command) [36157]
drivers/input/serio/i8042.c: f4 -> i8042 (parameter) [36157]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36160]
input: HP WMI hotkeys as /devices/virtual/input/input12
Non-volatile memory driver v1.3
EXT3 FS on sda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
fuse init (API version 7.13)
loop: module loaded
Adding 2401676k swap on /dev/sda6. Priority:-1 extents:1 across:2401676k
microcode: CPU0 sig=0x6fd, pf=0x80, revision=0xa3
platform microcode: firmware: requesting intel-ucode/06-0f-0d
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [43419]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [43420]
drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [43420]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [43423]
microcode: CPU1 sig=0x6fd, pf=0x80, revision=0xa3
platform microcode: firmware: requesting intel-ucode/06-0f-0d
Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
cfg80211: Calling CRDA for country: NL
cfg80211: Regulatory domain changed to country: NL
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
(5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth1: link is not ready
b43 ssb0:0: firmware: requesting b43/ucode13.fw
b43 ssb0:0: firmware: requesting b43/b0g0initvals13.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
ADDRCONF(NETDEV_UP): wlan0: link is not ready
e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
0000:00:19.0: eth1: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
NET: Registered protocol family 17
wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
wlan0: direct probe to AP 00:1b:90:76:d3:f0 (try 1)
wlan0: direct probe responded
wlan0: authenticate with AP 00:1b:90:76:d3:f0 (try 1)
wlan0: authenticated
wlan0: associate with AP 00:1b:90:76:d3:f0 (try 1)
wlan0: RX AssocResp from 00:1b:90:76:d3:f0 (capab=0x431 status=0 aid=142)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
cfg80211: Calling CRDA for country: NL
wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
cfg80211: Current regulatory domain updated by AP to: NL
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [52092]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52093]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [52093]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52096]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [52267]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52267]
drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [52267]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52270]
eth1: no IPv6 routers present
wlan0: no IPv6 routers present
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [827841]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [827842]
drivers/input/serio/i8042.c: 03 -> i8042 (kbd-data) [827842]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [827844]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3600107]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3600107]
drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [3600107]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3600110]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3660206]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3660207]
drivers/input/serio/i8042.c: 03 -> i8042 (kbd-data) [3660207]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3660209]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3900629]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3900630]
drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [3900630]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3900633]
