As requested here is the dmesg of a failed connection between kernel and
synaptics touchpad. Minute I added i8042.noloop=1 back to boot options
so I can have my mouse back everything works as expected.
On 07/29/09 21:45, Dmitry Torokhov wrote:
Hi Jory,
On Tue, Jul 28, 2009 at 10:11:46PM -0500, Jory A. Pratt wrote:
After further testing I realized there was a mistake in the patch. The
DMI_BOARD_VENDOR should have been
ASUSTeK Computer Inc. instead of ASUSTeK Computer INC. Patch has been
fully tested with 20+ reboots and cold
boots to ensure it is working properly.
Since you are saying that AUX loop detection usually works on your
laptop simply disabling it is not the best solution. Could you please
provide me with dmesg of booting with i8042.debug=1 when touchpad
is not detected?
Linux version 2.6.30-gentoo-r4 (root@pepsi) (gcc version 4.4.1 (Gentoo 4.4.1 p1.0) ) #1 SMP Wed Jul 29 22:03:25 CDT 2009
Command line: root=/dev/sda3 vga=0x369 i8042.debug=1
KERNEL supported cpus:
Intel GenuineIntel
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bffb0000 (usable)
BIOS-e820: 00000000bffb0000 - 00000000bffbe000 (ACPI data)
BIOS-e820: 00000000bffbe000 - 00000000bfff0000 (ACPI NVS)
BIOS-e820: 00000000bfff0000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
DMI 2.4 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x140000 max_arch_pfn = 0x100000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 0C0000000 mask FC0000000 uncachable
1 base 000000000 mask F00000000 write-back
2 base 100000000 mask FC0000000 write-back
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000c0000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbffb0 max_arch_pfn = 0x100000000
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e4000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 00000000bffb0000 (usable)
modified: 00000000bffb0000 - 00000000bffbe000 (ACPI data)
modified: 00000000bffbe000 - 00000000bfff0000 (ACPI NVS)
modified: 00000000bfff0000 - 00000000c0000000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000ffb00000 - 0000000100000000 (reserved)
modified: 0000000100000000 - 0000000140000000 (usable)
init_memory_mapping: 0000000000000000-00000000bffb0000
0000000000 - 00bfe00000 page 2M
00bfe00000 - 00bffb0000 page 4k
kernel direct mapping tables up to bffb0000 @ 10000-15000
init_memory_mapping: 0000000100000000-0000000140000000
0100000000 - 0140000000 page 2M
kernel direct mapping tables up to 140000000 @ 13000-19000
ACPI: RSDP 00000000000f81d0 00024 (v02 ACPIAM)
ACPI: XSDT 00000000bffb0100 0007C (v01 _ASUS_ Notebook 12000725 MSFT 00000097)
ACPI: FACP 00000000bffb0290 000F4 (v03 A_M_I_ OEMFACP 12000725 MSFT 00000097)
ACPI: DSDT 00000000bffb0680 0ADF0 (v01 G1S00 G1S00000 00000000 INTL 20061109)
ACPI: FACS 00000000bffbe000 00040
ACPI: APIC 00000000bffb0390 0005C (v01 A_M_I_ OEMAPIC 12000725 MSFT 00000097)
ACPI: MCFG 00000000bffb0430 0003C (v01 A_M_I_ OEMMCFG 12000725 MSFT 00000097)
ACPI: SLIC 00000000bffb0470 00176 (v01 _ASUS_ Notebook 12000725 MSFT 00000097)
ACPI: DBGP 00000000bffb03f0 00034 (v01 A_M_I_ OEMDBGP 12000725 MSFT 00000097)
ACPI: BOOT 00000000bffb05f0 00028 (v01 A_M_I_ OEMBOOT 12000725 MSFT 00000097)
ACPI: ECDT 00000000bffb0620 00054 (v01 A_M_I_ OEMECDT 12000725 MSFT 00000097)
ACPI: OEMB 00000000bffbe040 00060 (v01 A_M_I_ AMI_OEM 12000725 MSFT 00000097)
ACPI: HPET 00000000bffbb490 00038 (v01 A_M_I_ OEMHPET 12000725 MSFT 00000097)
ACPI: ATKG 00000000bffbe2a0 08024 (v01 A_M_I_ OEMATKG 05000702 MSFT 00000097)
ACPI: SSDT 00000000bffc6de0 004E6 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
(7 early reservations) ==> bootmem [0000000000 - 0140000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 0001830cd8] TEXT DATA BSS ==> [0001000000 - 0001830cd8]
#3 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#4 [0001831000 - 0001831240] BRK ==> [0001831000 - 0001831240]
#5 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000]
#6 [0000013000 - 0000014000] PGTABLE ==> [0000013000 - 0000014000]
[ffffe20000000000-ffffe200045fffff] PMD -> [ffff880028200000-ffff88002c7fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00140000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000bffb0
0: 0x00100000 -> 0x00140000
On node 0 totalpages: 1048383
DMA zone: 56 pages used for memmap
DMA zone: 103 pages reserved
DMA zone: 3824 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 767976 pages, LIFO batch:31
Normal zone: 3584 pages used for memmap
Normal zone: 258560 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
PM: Registered nosave memory: 00000000bffb0000 - 00000000bffbe000
PM: Registered nosave memory: 00000000bffbe000 - 00000000bfff0000
PM: Registered nosave memory: 00000000bfff0000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffb00000
PM: Registered nosave memory: 00000000ffb00000 - 0000000100000000
Allocating PCI resources starting at c4000000 (gap: c0000000:3ee00000)
NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 25 pages at ffff880028022000, static data 71840 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030360
Kernel command line: root=/dev/sda3 vga=0x369 i8042.debug=1
Initializing CPU#0
Experimental hierarchical RCU implementation.
Experimental hierarchical RCU init done.
NR_IRQS:2304
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 2194.656 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 4039964k/5242880k available (4636k kernel code, 1049348k absent, 152588k reserved, 1861k data, 360k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 4389.31 BogoMIPS (lpj=2194656)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring handled by SMI
using mwait in idle threads.
ACPI: Core revision 20090320
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping 0b
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4388.78 BogoMIPS (lpj=2194390)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8778.09 BogoMIPS).
net_namespace: 560 bytes
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base c0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base c0000000 segment 0 buses 0 - 255
PCI: MCFG area at c0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at c0000000 - cfffffff
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI Warning (tbutils-0246): Incorrect checksum in table [ATKG] - 2A, should be 59 [20090320]
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0xe080-0xe09f]
pci 0000:00:1a.1: reg 20 io port: [0xe000-0xe01f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfebff400-0xfebff7ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfebf8000-0xfebfbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xdc00-0xdc1f]
pci 0000:00:1d.1: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:1d.2: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebff000-0xfebff3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0250 (mask 000f)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x8f0-0x8f7]
pci 0000:00:1f.1: reg 1c io port: [0x8f8-0x8fb]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: reg 10 io port: [0xec00-0xec07]
pci 0000:00:1f.2: reg 14 io port: [0xe880-0xe883]
pci 0000:00:1f.2: reg 18 io port: [0xe800-0xe807]
pci 0000:00:1f.2: reg 1c io port: [0xe480-0xe483]
pci 0000:00:1f.2: reg 20 io port: [0xe400-0xe41f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfebff800-0xfebfffff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0x9c00-0x9c7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0xfdee0000-0xfdefffff]
pci 0000:00:01.0: bridge io port: [0x9000-0x9fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf7e00000-0xfdefffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd5d00000-0xf5cfffff]
pci 0000:02:00.0: reg 10 io port: [0xa800-0xa8ff]
pci 0000:02:00.0: reg 18 64bit mmio: [0xfdfff000-0xfdffffff]
pci 0000:02:00.0: reg 30 32bit mmio: [0xfdfc0000-0xfdfdffff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xa000-0xafff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfdf00000-0xfdffffff]
pci 0000:03:00.0: reg 10 64bit mmio: [0xfe0fe000-0xfe0fffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge 32bit mmio: [0xfe000000-0xfe0fffff]
pci 0000:00:1c.2: bridge io port: [0xb000-0xbfff]
pci 0000:00:1c.2: bridge 32bit mmio: [0xfe100000-0xfe8fffff]
pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf5d00000-0xf7cfffff]
pci 0000:07:00.0: reg 10 io port: [0xcc00-0xcc07]
pci 0000:07:00.0: reg 14 io port: [0xc880-0xc883]
pci 0000:07:00.0: reg 18 io port: [0xc800-0xc807]
pci 0000:07:00.0: reg 1c io port: [0xc480-0xc483]
pci 0000:07:00.0: reg 20 io port: [0xc400-0xc40f]
pci 0000:07:00.0: reg 24 32bit mmio: [0xfe9fe000-0xfe9fffff]
pci 0000:07:00.0: PME# supported from D3hot
pci 0000:07:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
pci 0000:08:01.0: reg 10 32bit mmio: [0xfeaff800-0xfeafffff]
pci 0000:08:01.0: PME# supported from D0 D3hot D3cold
pci 0000:08:01.0: PME# disabled
pci 0000:08:01.1: reg 10 32bit mmio: [0xfeaff400-0xfeaff4ff]
pci 0000:08:01.1: supports D1 D2
pci 0000:08:01.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:01.1: PME# disabled
pci 0000:08:01.2: reg 10 32bit mmio: [0xfeaff000-0xfeaff0ff]
pci 0000:08:01.2: supports D1 D2
pci 0000:08:01.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:01.2: PME# disabled
pci 0000:08:01.3: reg 10 32bit mmio: [0xfeafec00-0xfeafecff]
pci 0000:08:01.3: supports D1 D2
pci 0000:08:01.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:01.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 10 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *7 10 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs *6)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 10 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 12)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: WMI: Mapper loaded
PCI: Using ACPI for IRQ routing
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:08: ioport range 0x500-0x53f has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0a: ioport range 0x250-0x253 has been reserved
system 00:0a: ioport range 0x256-0x25f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xc0000000-0xcfffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff has been reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0xbfffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x9000-0x9fff
pci 0000:00:01.0: MEM window: 0xf7e00000-0xfdefffff
pci 0000:00:01.0: PREFETCH window: 0x000000d5d00000-0x000000f5cfffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0xa000-0xafff
pci 0000:00:1c.0: MEM window: 0xfdf00000-0xfdffffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: disabled
pci 0000:00:1c.1: MEM window: 0xfe000000-0xfe0fffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.2: IO window: 0xb000-0xbfff
pci 0000:00:1c.2: MEM window: 0xfe100000-0xfe8fffff
pci 0000:00:1c.2: PREFETCH window: 0x000000f5d00000-0x000000f7cfffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:06
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: disabled
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:07
pci 0000:00:1c.4: IO window: 0xc000-0xcfff
pci 0000:00:1c.4: MEM window: 0xfe900000-0xfe9fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:08
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
pci_bus 0000:01: resource 1 mem: [0xf7e00000-0xfdefffff]
pci_bus 0000:01: resource 2 pref mem [0xd5d00000-0xf5cfffff]
pci_bus 0000:02: resource 0 io: [0xa000-0xafff]
pci_bus 0000:02: resource 1 mem: [0xfdf00000-0xfdffffff]
pci_bus 0000:03: resource 1 mem: [0xfe000000-0xfe0fffff]
pci_bus 0000:04: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:04: resource 1 mem: [0xfe100000-0xfe8fffff]
pci_bus 0000:04: resource 2 pref mem [0xf5d00000-0xf7cfffff]
pci_bus 0000:07: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:07: resource 1 mem: [0xfe900000-0xfe9fffff]
pci_bus 0000:08: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:08: resource 3 io: [0x00-0xffff]
pci_bus 0000:08: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x52 set to 0x1
Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1248905526.323:1): initialized
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 7892
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.2: irq 27 for MSI/MSI-X
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.3: irq 28 for MSI/MSI-X
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.4: irq 29 for MSI/MSI-X
pcieport-driver 0000:00:1c.4: setting latency timer to 64
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
vesafb: framebuffer at 0xfb000000, mapped to 0xffffc20010100000, using 13781k, total 14336k
vesafb: mode is 1680x1050x32, linelength=6720, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Console: switching to colour frame buffer device 210x65
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC0] (on-line)
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Lid Switch [LID]
acpi device:07: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input3
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: SSDT 00000000bffc63a0 00286 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000bffc66c0 00712 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor ACPI_CPU:00: registered as cooling_device1
ACPI: Processor [P001] (supports 8 throttling states)
ACPI: SSDT 00000000bffc62d0 000C8 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000bffc6630 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2])
processor ACPI_CPU:01: registered as cooling_device2
ACPI: Processor [P002] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (76 C)
ACPI: Battery Slot [BAT0] (battery present)
floppy0: no floppy controllers found
loop: module loaded
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x2850 rev 0x03)
PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-T20L, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-cd driver 5.00
ide-cd: hda: ATAPI 24X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 20 (level, low) -> IRQ 20
ahci 0000:00:1f.2: irq 30 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfebff800 port 0xfebff900 irq 30
ata2: SATA max UDMA/133 abar m2048@0xfebff800 port 0xfebff980 irq 30
ata3: SATA max UDMA/133 abar m2048@0xfebff800 port 0xfebffa00 irq 30
ahci 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ahci 0000:07:00.0: AHCI 0001.0000 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:07:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ahci 0000:07:00.0: setting latency timer to 64
scsi3 : ahci
ata4: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe100 irq 16
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 31 for MSI/MSI-X
eth0: RTL8168b/8111b at 0xffffc2000004e000, 00:1d:60:6b:6a:5e, XID 38000000 IRQ 31
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27k
iwlagn: Copyright(c) 2003-2009 Intel Corporation
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: setting latency timer to 64
iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
iwlagn 0000:03:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels
iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X
phy0: Selected rate control algorithm 'iwl-agn-rs'
firewire_ohci 0000:08:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
firewire_ohci: Added fw-ohci device 0000:08:01.0, OHCI version 1.0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.30-gentoo-r4 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebff000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.30-gentoo-r4 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e080
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.30-gentoo-r4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.30-gentoo-r4 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000dc00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.30-gentoo-r4 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.30-gentoo-r4 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.1
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.30-gentoo-r4 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.2
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver berry_charge
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
drivers/input/serio/i8042.c: 20 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 45 <- i8042 (return) [1]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 54 -> i8042 (parameter) [1]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 5a -> i8042 (parameter) [1]
drivers/input/serio/i8042.c: 5a <- i8042 (return) [1]
drivers/input/serio/i8042.c: a7 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 20 -> i8042 (command) [1]
drivers/input/serio/i8042.c: 74 <- i8042 (return) [1]
drivers/input/serio/i8042.c: a8 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 20 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 54 <- i8042 (return) [2]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [2]
drivers/input/serio/i8042.c: 56 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
drivers/input/serio/i8042.c: a5 -> i8042 (parameter) [2]
drivers/input/serio/i8042.c: a5 <- i8042 (flush, aux) [252]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [252]
drivers/input/serio/i8042.c: 74 -> i8042 (parameter) [252]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [252]
drivers/input/serio/i8042.c: 65 -> i8042 (parameter) [252]
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
drivers/input/serio/i8042.c: f2 -> i8042 (kbd-data) [253]
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [255]
drivers/input/serio/i8042.c: ab <- i8042 (interrupt, 0, 1) [2194]
usb 1-1: new high speed USB device using ehci_hcd and address 2
ata4: SATA link down (SStatus 0 SControl 300)
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
drivers/input/serio/i8042.c: 41 <- i8042 (interrupt, 0, 1) [2194]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [2194]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2257]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [2257]
ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:08:01.1: SDHCI controller found [1180:0822] (rev 22)
sdhci-pci 0000:08:01.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2260]
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:08:01.1] using PIO
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usbcore: registered new interface driver asus-oled
asus-laptop: Asus Laptop Support version 0.42
asus-laptop: G1S model detected
asus-laptop: Brightness ignored, must be controlled by ACPI video driver
input: Asus Laptop extra buttons as /devices/virtual/input/input4
Registered led device: asus::mail
Registered led device: asus::touchpad
Registered led device: asus::gaming
Advanced Linux Sound Architecture Driver Version 1.0.20.
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
drivers/input/serio/i8042.c: f3 -> i8042 (kbd-data) [2762]
firewire_core: created device fw0: GUID 00e0180003a482f6, S400
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2764]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [2764]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2765]
drivers/input/serio/i8042.c: f4 -> i8042 (kbd-data) [2784]
ata1.00: ATA-8: Hitachi HTS722016K9SA00, DCDOC54P, max UDMA/133
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2806]
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS72201 DCDO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
sda1 sda2 sda3 sda4 <<6>ALSA device list:
usb 1-1: New USB device found, idVendor=04f2, idProduct=b012
usb 1-1: New USB device strings: Mfr=2, Product=1, SerialNumber=3
usb 1-1: Product: USB2.0 1.3M UVC WebCam
usb 1-1: Manufacturer: Chicony Electronics Co., Ltd.
usb 1-1: SerialNumber: SN0001
usb 1-1: configuration #1 chosen from 1 choice
#0: HDA Intel at 0xfebf8000 irq 22
uvcvideo: Found UVC 1.00 device USB2.0 1.3M UVC WebCam (04f2:b012)
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
input: USB2.0 1.3M UVC WebCam as /devices/pci0000:00/0000:00:1a.7/usb1/1-1/1-1:1.0/input/input6
sda5<6>Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.11
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
usb 1-2: new high speed USB device using ehci_hcd and address 3
rtc_cmos 00:03: setting system clock to 2009-07-29 22:12:17 UTC (1248905537)
mmc0: new SD card at address b368
sda6<6>mmcblk0: mmc0:b368 SD01G 958 MiB
mmcblk0: p1
sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-2: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 0, changing to 9
usb 1-2: config 1 interface 0 altsetting 0 endpoint 0x2 has an invalid bInterval 0, changing to 9
usb 1-2: New USB device found, idVendor=0b05, idProduct=1726
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: LCM
usb 1-2: Manufacturer: ASUS
usb 1-2: configuration #1 chosen from 1 choice
asus-oled 1-2:1.0: Attached Asus OLED device: G1/G2 [width 128, pack_mode 0]
UDF-fs: No partition found (1)
XFS mounting filesystem sda3
usb 2-3: new high speed USB device using ehci_hcd and address 2
Ending clean XFS mount for filesystem: sda3
VFS: Mounted root (xfs filesystem) readonly on device 8:3.
Freeing unused kernel memory: 360k freed
usb 2-3: New USB device found, idVendor=0781, idProduct=5406
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: U3 Cruzer Micro
usb 2-3: Manufacturer: SanDisk
usb 2-3: SerialNumber: 173870168F82862A
usb 2-3: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 7-2: new full speed USB device using uhci_hcd and address 2
Clocksource tsc unstable (delta = -169025684 ns)
usb 7-2: New USB device found, idVendor=0b05, idProduct=1712
usb 7-2: New USB device strings: Mfr=0, Product=0, SerialNumber=3
usb 7-2: SerialNumber: 0194E8-5B-0002
usb 7-2: configuration #1 chosen from 1 choice
udev: starting version 141
udev: renamed network interface eth0 to lan0
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.29 Wed Jul 22 23:04:30 PDT 2009
scsi 4:0:0:0: Direct-Access SanDisk Cruzer 7.01 PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
sd 4:0:0:0: [sdb] 31306239 512-byte hardware sectors: (16.0 GB/14.9 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI removable disk
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
microcode: CPU0 updated from revision 0xb3 to 0xb6, date = 2007-07-13
microcode: CPU1 updated from revision 0xb3 to 0xb6, date = 2007-07-13
Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k
r8169: lan0: link down
iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode
iwlagn 0000:03:00.0: loaded firmware version 228.57.2.23
Registered led device: iwl-phy0::radio
Registered led device: iwl-phy0::assoc
Registered led device: iwl-phy0::RX
Registered led device: iwl-phy0::TX
drivers/input/serio/i8042.c: 1d <- i8042 (interrupt, 0, 1) [27034]
drivers/input/serio/i8042.c: 38 <- i8042 (interrupt, 0, 1) [27162]
drivers/input/serio/i8042.c: 38 <- i8042 (interrupt, 0, 1) [27403]
drivers/input/serio/i8042.c: 38 <- i8042 (interrupt, 0, 1) [27437]
drivers/input/serio/i8042.c: 3b <- i8042 (interrupt, 0, 1) [27456]
drivers/input/serio/i8042.c: bb <- i8042 (interrupt, 0, 1) [27599]
drivers/input/serio/i8042.c: 9d <- i8042 (interrupt, 0, 1) [27682]
drivers/input/serio/i8042.c: b8 <- i8042 (interrupt, 0, 1) [27716]
wlan0: authenticate with AP 00:1d:7e:f8:d9:8a
wlan0: authenticated
wlan0: associate with AP 00:1d:7e:f8:d9:8a
wlan0: RX AssocResp from 00:1d:7e:f8:d9:8a (capab=0x411 status=0 aid=2)
wlan0: associated
drivers/input/serio/i8042.c: 1e <- i8042 (interrupt, 0, 1) [29563]
drivers/input/serio/i8042.c: 9e <- i8042 (interrupt, 0, 1) [29686]
drivers/input/serio/i8042.c: 31 <- i8042 (interrupt, 0, 1) [29738]
drivers/input/serio/i8042.c: 1e <- i8042 (interrupt, 0, 1) [29817]
drivers/input/serio/i8042.c: b1 <- i8042 (interrupt, 0, 1) [29861]
drivers/input/serio/i8042.c: 13 <- i8042 (interrupt, 0, 1) [29944]
drivers/input/serio/i8042.c: 9e <- i8042 (interrupt, 0, 1) [30013]
drivers/input/serio/i8042.c: 93 <- i8042 (interrupt, 0, 1) [30062]
drivers/input/serio/i8042.c: 2e <- i8042 (interrupt, 0, 1) [30183]
drivers/input/serio/i8042.c: 23 <- i8042 (interrupt, 0, 1) [30275]
drivers/input/serio/i8042.c: ae <- i8042 (interrupt, 0, 1) [30349]
drivers/input/serio/i8042.c: a3 <- i8042 (interrupt, 0, 1) [30384]
drivers/input/serio/i8042.c: 15 <- i8042 (interrupt, 0, 1) [30441]
drivers/input/serio/i8042.c: 95 <- i8042 (interrupt, 0, 1) [30534]
drivers/input/serio/i8042.c: 1c <- i8042 (interrupt, 0, 1) [30657]
drivers/input/serio/i8042.c: 9c <- i8042 (interrupt, 0, 1) [30794]
drivers/input/serio/i8042.c: 2a <- i8042 (interrupt, 0, 1) [30826]
drivers/input/serio/i8042.c: 2a <- i8042 (interrupt, 0, 1) [31066]
drivers/input/serio/i8042.c: 21 <- i8042 (interrupt, 0, 1) [31071]
drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 0, 1) [31203]
drivers/input/serio/i8042.c: a1 <- i8042 (interrupt, 0, 1) [31213]
drivers/input/serio/i8042.c: 16 <- i8042 (interrupt, 0, 1) [31228]
drivers/input/serio/i8042.c: 96 <- i8042 (interrupt, 0, 1) [31340]
drivers/input/serio/i8042.c: 2e <- i8042 (interrupt, 0, 1) [31346]
drivers/input/serio/i8042.c: ae <- i8042 (interrupt, 0, 1) [31468]
drivers/input/serio/i8042.c: 25 <- i8042 (interrupt, 0, 1) [31514]
drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 0, 1) [31631]
drivers/input/serio/i8042.c: a5 <- i8042 (interrupt, 0, 1) [31656]
drivers/input/serio/i8042.c: 13 <- i8042 (interrupt, 0, 1) [31685]
drivers/input/serio/i8042.c: 92 <- i8042 (interrupt, 0, 1) [31768]
drivers/input/serio/i8042.c: 1c <- i8042 (interrupt, 0, 1) [31828]
drivers/input/serio/i8042.c: 93 <- i8042 (interrupt, 0, 1) [31862]
drivers/input/serio/i8042.c: 9c <- i8042 (interrupt, 0, 1) [31974]
drivers/input/serio/i8042.c: 2e <- i8042 (interrupt, 0, 1) [32271]
drivers/input/serio/i8042.c: ae <- i8042 (interrupt, 0, 1) [32422]
drivers/input/serio/i8042.c: 26 <- i8042 (interrupt, 0, 1) [32448]
drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 0, 1) [32576]
drivers/input/serio/i8042.c: a6 <- i8042 (interrupt, 0, 1) [32580]
drivers/input/serio/i8042.c: 1e <- i8042 (interrupt, 0, 1) [32659]
drivers/input/serio/i8042.c: 92 <- i8042 (interrupt, 0, 1) [32698]
drivers/input/serio/i8042.c: 13 <- i8042 (interrupt, 0, 1) [32757]
drivers/input/serio/i8042.c: 9e <- i8042 (interrupt, 0, 1) [32845]
drivers/input/serio/i8042.c: 1c <- i8042 (interrupt, 0, 1) [32884]
drivers/input/serio/i8042.c: 93 <- i8042 (interrupt, 0, 1) [32889]
drivers/input/serio/i8042.c: 9c <- i8042 (interrupt, 0, 1) [33017]
drivers/input/serio/i8042.c: 20 <- i8042 (interrupt, 0, 1) [33289]
drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 0, 1) [33446]
drivers/input/serio/i8042.c: 32 <- i8042 (interrupt, 0, 1) [33456]
drivers/input/serio/i8042.c: b2 <- i8042 (interrupt, 0, 1) [33583]
drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 0, 1) [33934]
drivers/input/serio/i8042.c: 1f <- i8042 (interrupt, 0, 1) [34032]
drivers/input/serio/i8042.c: 92 <- i8042 (interrupt, 0, 1) [34062]
drivers/input/serio/i8042.c: 9f <- i8042 (interrupt, 0, 1) [34164]
drivers/input/serio/i8042.c: 22 <- i8042 (interrupt, 0, 1) [34236]
drivers/input/serio/i8042.c: 39 <- i8042 (interrupt, 0, 1) [34345]
drivers/input/serio/i8042.c: a2 <- i8042 (interrupt, 0, 1) [34369]
drivers/input/serio/i8042.c: b9 <- i8042 (interrupt, 0, 1) [34467]
drivers/input/serio/i8042.c: 36 <- i8042 (interrupt, 0, 1) [35248]
drivers/input/serio/i8042.c: 36 <- i8042 (interrupt, 0, 1) [35488]
drivers/input/serio/i8042.c: 36 <- i8042 (interrupt, 0, 1) [35522]
drivers/input/serio/i8042.c: 36 <- i8042 (interrupt, 0, 1) [35556]
drivers/input/serio/i8042.c: 34 <- i8042 (interrupt, 0, 1) [35562]
drivers/input/serio/i8042.c: b4 <- i8042 (interrupt, 0, 1) [35660]
drivers/input/serio/i8042.c: 34 <- i8042 (interrupt, 0, 1) [35718]
drivers/input/serio/i8042.c: b4 <- i8042 (interrupt, 0, 1) [35846]
drivers/input/serio/i8042.c: b6 <- i8042 (interrupt, 0, 1) [35870]
drivers/input/serio/i8042.c: 39 <- i8042 (interrupt, 0, 1) [36062]
drivers/input/serio/i8042.c: b9 <- i8042 (interrupt, 0, 1) [36204]
drivers/input/serio/i8042.c: 20 <- i8042 (interrupt, 0, 1) [36230]
drivers/input/serio/i8042.c: 32 <- i8042 (interrupt, 0, 1) [36352]
drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 0, 1) [36362]
drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 0, 1) [36465]
drivers/input/serio/i8042.c: b2 <- i8042 (interrupt, 0, 1) [36495]
drivers/input/serio/i8042.c: 1f <- i8042 (interrupt, 0, 1) [36534]
drivers/input/serio/i8042.c: 92 <- i8042 (interrupt, 0, 1) [36608]
drivers/input/serio/i8042.c: 9f <- i8042 (interrupt, 0, 1) [36686]
drivers/input/serio/i8042.c: 22 <- i8042 (interrupt, 0, 1) [36761]
drivers/input/serio/i8042.c: 34 <- i8042 (interrupt, 0, 1) [36874]
drivers/input/serio/i8042.c: a2 <- i8042 (interrupt, 0, 1) [36893]
drivers/input/serio/i8042.c: b4 <- i8042 (interrupt, 0, 1) [37021]
drivers/input/serio/i8042.c: 14 <- i8042 (interrupt, 0, 1) [37104]
drivers/input/serio/i8042.c: 94 <- i8042 (interrupt, 0, 1) [37226]
drivers/input/serio/i8042.c: 2d <- i8042 (interrupt, 0, 1) [37374]
drivers/input/serio/i8042.c: ad <- i8042 (interrupt, 0, 1) [37497]
drivers/input/serio/i8042.c: 14 <- i8042 (interrupt, 0, 1) [37605]
drivers/input/serio/i8042.c: 94 <- i8042 (interrupt, 0, 1) [37718]
drivers/input/serio/i8042.c: 1c <- i8042 (interrupt, 0, 1) [37739]
