Supplied is a driver for the TSC2003. There is actually a driver for TSC2007 which can be used in some cases.
The platform struct is reused from the TSC2007.
There is a big difference in the implementation between the drivers, this one does not use HR timers.
The TSC2007 driver performs synchronous I2C in the timer callback (SW IRQ context) which is bad when
the I2C driver is interrupt driven.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@xxxxxxxxxxxxxxx>
---
Index: linux-2.6.30-rc7/drivers/input/touchscreen/tsc2003.c
===================================================================
--- linux-2.6.30-rc7/drivers/input/touchscreen/tsc2003.c (revision 0)
+++ linux-2.6.30-rc7/drivers/input/touchscreen/tsc2003.c (revision 869)
@@ -0,0 +1,387 @@
+/*
+ * tsc2003.c Driver for TI TSC2003 touch screen controller
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * TI TSC2003
+ *
+ * Inspired by tsc2007, Copyright (c) 2008 MtekVision Co., Ltd.
+ */
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/i2c/tsc2007.h>
+#include <linux/kthread.h>
+#include <linux/semaphore.h>
+
+#define TSC2003_DRIVER_NAME "tsc2003"
+
+#define TS_POLL_PERIOD 20 /* ms delay between samples */
+
+#define TSC2003_MEASURE_TEMP0 (0x0 << 4)
+#define TSC2003_MEASURE_AUX (0x2 << 4)
+#define TSC2003_MEASURE_TEMP1 (0x4 << 4)
+#define TSC2003_ACTIVATE_XN (0x8 << 4)
+#define TSC2003_ACTIVATE_YN (0x9 << 4)
+#define TSC2003_ACTIVATE_YP_XN (0xa << 4)
+#define TSC2003_SETUP (0xb << 4)
+#define TSC2003_MEASURE_X (0xc << 4)
+#define TSC2003_MEASURE_Y (0xd << 4)
+#define TSC2003_MEASURE_Z1 (0xe << 4)
+#define TSC2003_MEASURE_Z2 (0xf << 4)
+
+#define TSC2003_POWER_OFF_IRQ_EN (0x0 << 2)
+#define TSC2003_ADC_ON_IRQ_DIS0 (0x1 << 2)
+#define TSC2003_ADC_OFF_IRQ_EN (0x2 << 2)
+#define TSC2003_ADC_ON_IRQ_DIS1 (0x3 << 2)
+
+#define TSC2003_12BIT (0x0 << 1)
+#define TSC2003_8BIT (0x1 << 1)
+
+#define MAX_12BIT ((1 << 12) - 1)
+
+#define ADC_ON_12BIT (TSC2003_12BIT | TSC2003_ADC_ON_IRQ_DIS0)
+
+#define READ_Y (ADC_ON_12BIT | TSC2003_MEASURE_Y)
+#define READ_Z1 (ADC_ON_12BIT | TSC2003_MEASURE_Z1)
+#define READ_Z2 (ADC_ON_12BIT | TSC2003_MEASURE_Z2)
+#define READ_X (ADC_ON_12BIT | TSC2003_MEASURE_X)
+#define PWRDOWN (TSC2003_12BIT | TSC2003_POWER_OFF_IRQ_EN)
+
+struct ts_event {
+ int x;
+ int y;
+ int z1, z2;
+};
+
+struct tsc2003 {
+ struct input_dev *input;
+ char phys[32];
+ struct task_struct *task;
+ struct ts_event tc;
+ struct completion penirq_completion;
+
+ struct i2c_client *client;
+
+ u16 model;
+ u16 x_plate_ohms;
+
+ unsigned pendown;
+};
+
+static inline int tsc2003_xfer(struct tsc2003 *tsc, u8 cmd)
+{
+ s32 data;
+ u16 val;
+
+ data = i2c_smbus_read_word_data(tsc->client, cmd);
+ if (data < 0) {
+ dev_err(&tsc->client->dev, "i2c io error: %d\n", data);
+ return data;
+ }
+
+ /* The protocol and raw data format from i2c interface:
+ * S Addr Wr [A] Comm [A] S Addr Rd [A] [DataLow] A [DataHigh] NA P
+ * Where DataLow has [D11-D4], DataHigh has [D3-D0 << 4 | Dummy 4bit].
+ */
+ val = swab16(data) >> 4;
+
+ dev_dbg(&tsc->client->dev, "data: 0x%x, val: 0x%x\n", data, val);
+
+ return val;
+}
+
+static void tsc2003_send_event(void *tsc)
+{
+ struct tsc2003 *ts = tsc;
+ struct input_dev *input = ts->input;
+ u32 rt = 0;
+ u16 x, y, z1, z2;
+
+ x = ts->tc.x;
+ y = ts->tc.y;
+ z1 = ts->tc.z1;
+ z2 = ts->tc.z2;
+
+ /* range filtering */
+ if (x == MAX_12BIT)
+ x = 0;
+
+ if (likely(x && z1)) {
+ /* compute touch pressure resistance using equation #1 */
+ rt = z2;
+ rt -= z1;
+ rt *= x;
+ rt *= ts->x_plate_ohms;
+ rt /= z1;
+ rt = (rt + 2047) >> 12;
+ }
+
+ /* Sample found inconsistent by debouncing or pressure is beyond
+ * the maximum. Don't report it to user space, repeat at least
+ * once more the measurement
+ */
+ if (rt > MAX_12BIT)
+ return;
+
+ /* NOTE: We can't rely on the pressure to determine the pen down
+ * state, even this controller has a pressure sensor. The pressure
+ * value can fluctuate for quite a while after lifting the pen and
+ * in some cases may not even settle at the expected value.
+ *
+ * The only safe way to check for the pen up condition is in the
+ * timer by reading the pen signal state (it's a GPIO _and_ IRQ).
+ */
+ if (rt) {
+ if (!ts->pendown) {
+ dev_dbg(&ts->client->dev, "DOWN\n");
+
+ input_report_key(input, BTN_TOUCH, 1);
+ ts->pendown = 1;
+ }
+
+ input_report_abs(input, ABS_X, x);
+ input_report_abs(input, ABS_Y, y);
+ input_report_abs(input, ABS_PRESSURE, rt);
+
+ input_sync(input);
+
+ dev_dbg(&ts->client->dev, "point(%4d,%4d), pressure (%4u)\n",
+ x, y, rt);
+ } else if (ts->pendown) {
+ /* pen up */
+ dev_dbg(&ts->client->dev, "UP\n");
+ input_report_key(input, BTN_TOUCH, 0);
+ input_report_abs(input, ABS_PRESSURE, 0);
+ input_sync(input);
+
+ ts->pendown = 0;
+ }
+}
+
+static int tsc2003_power_off_irq_en(struct tsc2003 *tsc)
+{
+ /* power down */
+ return tsc2003_xfer(tsc, PWRDOWN);
+}
+
+static int tsc2003_read_values(struct tsc2003 *tsc)
+{
+ /* y- still on; turn on only y+ (and ADC) */
+ tsc->tc.y = tsc2003_xfer(tsc, READ_Y);
+ if (tsc->tc.y < 0)
+ return tsc->tc.y;
+
+ /* turn y- off, x+ on, then leave in lowpower */
+ tsc->tc.x = tsc2003_xfer(tsc, READ_X);
+ if (tsc->tc.x < 0)
+ return tsc->tc.x;
+
+ /* turn y+ off, x- on; we'll use formula #1 */
+ tsc->tc.z1 = tsc2003_xfer(tsc, READ_Z1);
+ if (tsc->tc.z1 < 0)
+ return tsc->tc.z1;
+
+ tsc->tc.z2 = tsc2003_xfer(tsc, READ_Z2);
+ if (tsc->tc.z2 < 0)
+ return tsc->tc.z2;
+
+ return 0;
+}
+
+
+static irqreturn_t tsc2003_irq(int irq, void *handle)
+{
+ struct tsc2003 *ts = handle;
+
+ /* do not call the synced version -> deadlock */
+ disable_irq_nosync(irq);
+ /* signal the thread to continue */
+ complete(&ts->penirq_completion);
+
+ return IRQ_HANDLED;
+}
+
+static int tsc2003_thread(void *d)
+{
+ struct tsc2003 *ts = (struct tsc2003 *)d;
+ int ret;
+
+ allow_signal(SIGKILL);
+
+ while (!signal_pending(current)) {
+ /* power down and wait for interrupt */
+ do {
+ /* loop because the I2C bus might be busy */
+ ret = msleep_interruptible(TS_POLL_PERIOD);
+ if (!ret)
+ ret = tsc2003_power_off_irq_en(ts);
+ } while (ret == -EAGAIN && !signal_pending(current));
+
+ if (signal_pending(current))
+ break;
+
+ ret = wait_for_completion_interruptible(&ts->penirq_completion);
+ if (!ret) {
+ int first = 1;
+ /* got IRQ, start poll, until pen is up */
+ while (!ret && !signal_pending(current)
+ && (first || ts->pendown)) {
+ ret = tsc2003_read_values(ts);
+ if (!ret)
+ tsc2003_send_event(ts);
+ ret = msleep_interruptible(TS_POLL_PERIOD);
+ first = 0;
+ }
+
+ /* we re enable the interrupt */
+ if (!signal_pending(current))
+ enable_irq(ts->client->irq);
+ }
+ }
+
+ return 0;
+}
+
+static int tsc2003_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct tsc2003 *ts;
+ struct tsc2007_platform_data *pdata = client->dev.platform_data;
+ struct input_dev *input_dev;
+ int err;
+
+ if (!pdata) {
+ dev_err(&client->dev, "platform data is required!\n");
+ return -EINVAL;
+ }
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_WORD_DATA))
+ return -EIO;
+
+ ts = kzalloc(sizeof(struct tsc2003), GFP_KERNEL);
+ input_dev = input_allocate_device();
+ if (!ts || !input_dev) {
+ err = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ ts->client = client;
+ i2c_set_clientdata(client, ts);
+
+ ts->input = input_dev;
+
+ ts->model = pdata->model;
+ ts->x_plate_ohms = pdata->x_plate_ohms;
+
+ snprintf(ts->phys, sizeof(ts->phys),
+ "%s/input0", dev_name(&client->dev));
+
+ input_dev->name = TSC2003_DRIVER_NAME" Touchscreen";
+ input_dev->phys = ts->phys;
+ input_dev->id.bustype = BUS_I2C;
+
+ input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+
+ input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
+ input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
+
+ init_completion(&ts->penirq_completion);
+
+ ts->task = kthread_run(tsc2003_thread, ts, TSC2003_DRIVER_NAME);
+ if (IS_ERR(ts->task)) {
+ err = PTR_ERR(ts->task);
+ goto err_free_mem;
+ }
+
+ err = request_irq(client->irq, tsc2003_irq, 0,
+ client->dev.driver->name, ts);
+ if (err < 0) {
+ dev_err(&client->dev, "irq %d busy?\n", client->irq);
+ goto err_free_thread;
+ }
+
+ err = input_register_device(input_dev);
+ if (err)
+ goto err_free_irq;
+
+ dev_info(&client->dev, "registered with irq (%d)\n", client->irq);
+
+ return 0;
+
+ err_free_irq:
+ free_irq(client->irq, ts);
+ err_free_thread:
+ kthread_stop(ts->task);
+ err_free_mem:
+ input_free_device(input_dev);
+ kfree(ts);
+ return err;
+}
+
+static int tsc2003_remove(struct i2c_client *client)
+{
+ struct tsc2003 *ts = i2c_get_clientdata(client);
+
+ free_irq(client->irq, ts);
+ send_sig(SIGKILL, ts->task, 1);
+ kthread_stop(ts->task);
+ input_unregister_device(ts->input);
+ kfree(ts);
+
+ return 0;
+}
+
+static struct i2c_device_id tsc2003_idtable[] = {
+ { TSC2003_DRIVER_NAME, 0 },
+ { }
+};
+
+MODULE_DEVICE_TABLE(i2c, tsc2003_idtable);
+
+static struct i2c_driver tsc2003_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = TSC2003_DRIVER_NAME,
+ .bus = &i2c_bus_type,
+ },
+ .id_table = tsc2003_idtable,
+ .probe = tsc2003_probe,
+ .remove = tsc2003_remove,
+};
+
+static int __init tsc2003_init(void)
+{
+ return i2c_add_driver(&tsc2003_driver);
+}
+
+static void __exit tsc2003_exit(void)
+{
+ i2c_del_driver(&tsc2003_driver);
+}
+
+module_init(tsc2003_init);
+module_exit(tsc2003_exit);
+
+MODULE_AUTHOR("Mocean Laboratories <info@xxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("TSC2003 TouchScreen Driver");
+MODULE_LICENSE("GPL v2");
+
Index: linux-2.6.30-rc7/drivers/input/touchscreen/Kconfig
===================================================================
--- linux-2.6.30-rc7/drivers/input/touchscreen/Kconfig (revision 861)
+++ linux-2.6.30-rc7/drivers/input/touchscreen/Kconfig (revision 869)
@@ -455,6 +455,17 @@
To compile this driver as a module, choose M here: the
module will be called touchit213.
+config TOUCHSCREEN_TSC2003
+ tristate "TSC2003 based touchscreens"
+ depends on I2C
+ help
+ Say Y here if you have a TSC2003 based touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc2003.
+
config TOUCHSCREEN_TSC2007
tristate "TSC2007 based touchscreens"
depends on I2C
Index: linux-2.6.30-rc7/drivers/input/touchscreen/Makefile
===================================================================
--- linux-2.6.30-rc7/drivers/input/touchscreen/Makefile (revision 861)
+++ linux-2.6.30-rc7/drivers/input/touchscreen/Makefile (revision 869)
@@ -27,6 +27,7 @@
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
+obj-$(CONFIG_TOUCHSCREEN_TSC2003) += tsc2003.o
obj-$(CONFIG_TOUCHSCREEN_TSC2007) += tsc2007.o
obj-$(CONFIG_TOUCHSCREEN_UCB1400) += ucb1400_ts.o
obj-$(CONFIG_TOUCHSCREEN_WACOM_W8001) += wacom_w8001.o
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
