Hi Alexandru,
ardeleanalex@xxxxxxxxx wrote on Thu, 16 Dec 2021 08:47:02 +0200:
> On Wed, Dec 15, 2021 at 10:03 PM Miquel Raynal
> <miquel.raynal@xxxxxxxxxxx> wrote:
> >
> > This is an internal variable of the core, let's use the
> > iio_buffer_enabled() helper which is exported for the following purpose:
> > telling if the current mode is a buffered mode, which is precisely what
> > this driver looks for.
> >
> > Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
> > ---
> > drivers/iio/adc/stm32-dfsdm-adc.c | 5 ++---
> > 1 file changed, 2 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/iio/adc/stm32-dfsdm-adc.c b/drivers/iio/adc/stm32-dfsdm-adc.c
> > index 1cfefb3b5e56..a3b8827d3bbf 100644
> > --- a/drivers/iio/adc/stm32-dfsdm-adc.c
> > +++ b/drivers/iio/adc/stm32-dfsdm-adc.c
> > @@ -466,8 +466,7 @@ static int stm32_dfsdm_channels_configure(struct iio_dev *indio_dev,
> > * In continuous mode, use fast mode configuration,
> > * if it provides a better resolution.
> > */
> > - if (adc->nconv == 1 && !trig &&
> > - (indio_dev->currentmode & INDIO_BUFFER_SOFTWARE)) {
> > + if (adc->nconv == 1 && !trig && iio_buffer_enabled(indio_dev)) {
>
> This may become tricky if other modes get added later.
> STM does a relatively good job in updating and re-using their drivers
> (even if some of them do look quirky sometimes).
>
> So, the question here would be: is "iio_buffer_enabled(indio_dev)"
> going to be valid [in this place] once INDIO_BUFFER_TRIGGERED or
> INDIO_BUFFER_HARDWARE get added?
I would argue, is this a real problem? Today iio_buffer_enabled() seem
to handle well what this driver is expecting. If tomorrow someone adds
another mode, that is his/her responsibility to state "okay, this
section is not common to all buffer styles *anymore*, so we need to do
a more fine grained check against ->currentmodes than
iio_buffer_enabled() does". In that case using the ->currentmodes
getter would be the right way to go, but only at that particular
moment, not today.
>
> I'd also ping some STM people for some feedback, acks or testing.
>
> > if (fl->flo[1].res >= fl->flo[0].res) {
> > fl->fast = 1;
> > flo = &fl->flo[1];
> > @@ -562,7 +561,7 @@ static int stm32_dfsdm_filter_configure(struct iio_dev *indio_dev,
> > cr1 = DFSDM_CR1_RCH(chan->channel);
> >
> > /* Continuous conversions triggered by SPI clk in buffer mode */
> > - if (indio_dev->currentmode & INDIO_BUFFER_SOFTWARE)
> > + if (iio_buffer_enabled(indio_dev))
> > cr1 |= DFSDM_CR1_RCONT(1);
> >
> > cr1 |= DFSDM_CR1_RSYNC(fl->sync_mode);
> > --
> > 2.27.0
> >
Thanks,
Miquèl
