Re: [PATCH v2 2/3] iio: sps30: add support for serial interface

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, 2 May 2021 15:44:30 +0200
Tomasz Duszynski <tomasz.duszynski@xxxxxxxxxxx> wrote:

> Sensor has support for both i2c and serial communication interfaces.
> Both offer very similar set of features. Minor differences don't impact
> overall functionality like doing measurements, etc.
> 
> Support for i2c have already been added, this patch adds support
> for the latter ie. serial interface.
> 
> Signed-off-by: Tomasz Duszynski <tomasz.duszynski@xxxxxxxxxxx>
Two trivial comments inline.  I'm happy to tidy those up whilst applying if
everyone else is happy with this and you don't need to do a v3.

Thanks,

Jonathan

> ---
>  MAINTAINERS                         |   1 +
>  drivers/iio/chemical/Kconfig        |  11 +
>  drivers/iio/chemical/Makefile       |   1 +
>  drivers/iio/chemical/sps30_serial.c | 428 ++++++++++++++++++++++++++++
>  4 files changed, 441 insertions(+)
>  create mode 100644 drivers/iio/chemical/sps30_serial.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 4b39a9c48736..cab9a63ad2cf 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -16138,6 +16138,7 @@ S:	Maintained
>  F:	Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.yaml
>  F:	drivers/iio/chemical/sps30.c
>  F:	drivers/iio/chemical/sps30_i2c.c
> +F:	drivers/iio/chemical/sps30_serial.c
>  
>  SERIAL DEVICE BUS
>  M:	Rob Herring <robh@xxxxxxxxxx>
> diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig
> index 2b45a76ab7bc..a4920646e9be 100644
> --- a/drivers/iio/chemical/Kconfig
> +++ b/drivers/iio/chemical/Kconfig
> @@ -148,6 +148,17 @@ config SPS30_I2C
>  	  To compile this driver as a module, choose M here: the module will
>  	  be called sps30_i2c.
>  
> +config SPS30_SERIAL
> +	tristate "SPS30 particulate matter sensor serial driver"
> +	depends on SERIAL_DEV_BUS
> +	select SPS30
> +	help
> +	  Say Y here to build support for the Sensirion SPS30 serial interface
> +	  driver.
> +
> +	  To compile this driver as a module, choose M here: the module will
> +	  be called sps30_serial.
> +
>  config VZ89X
>  	tristate "SGX Sensortech MiCS VZ89X VOC sensor"
>  	depends on I2C
> diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile
> index 41c264a229c0..4898690cc155 100644
> --- a/drivers/iio/chemical/Makefile
> +++ b/drivers/iio/chemical/Makefile
> @@ -18,4 +18,5 @@ obj-$(CONFIG_SCD30_SERIAL) += scd30_serial.o
>  obj-$(CONFIG_SENSIRION_SGP30)	+= sgp30.o
>  obj-$(CONFIG_SPS30) += sps30.o
>  obj-$(CONFIG_SPS30_I2C) += sps30_i2c.o
> +obj-$(CONFIG_SPS30_SERIAL) += sps30_serial.o
>  obj-$(CONFIG_VZ89X)		+= vz89x.o
> diff --git a/drivers/iio/chemical/sps30_serial.c b/drivers/iio/chemical/sps30_serial.c
> new file mode 100644
> index 000000000000..3dc1a9e2ae82
> --- /dev/null
> +++ b/drivers/iio/chemical/sps30_serial.c
> @@ -0,0 +1,428 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Sensirion SPS30 particulate matter sensor serial driver
> + *
> + * Copyright (c) 2021 Tomasz Duszynski <tomasz.duszynski@xxxxxxxxxxx>
> + */
> +#include <linux/completion.h>
> +#include <linux/device.h>
> +#include <linux/errno.h>
> +#include <linux/iio/iio.h>
> +#include <linux/minmax.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/serdev.h>
> +#include <linux/types.h>
> +
> +#include "sps30.h"
> +
> +#define SPS30_SERIAL_DEV_NAME "sps30"
> +
> +#define SPS30_SERIAL_SOF_EOF 0x7e
> +#define SPS30_SERIAL_TIMEOUT msecs_to_jiffies(20)
> +#define SPS30_SERIAL_MAX_BUF_SIZE 263
> +#define SPS30_SERIAL_ESCAPE_CHAR 0x7d
> +
> +#define SPS30_SERIAL_FRAME_MIN_SIZE 7
> +#define SPS30_SERIAL_FRAME_ADR_OFFSET 1
> +#define SPS30_SERIAL_FRAME_CMD_OFFSET 2
> +#define SPS30_SERIAL_FRAME_MOSI_LEN_OFFSET 3
> +#define SPS30_SERIAL_FRAME_MISO_STATE_OFFSET 3
> +#define SPS30_SERIAL_FRAME_MISO_LEN_OFFSET 4
> +#define SPS30_SERIAL_FRAME_MISO_DATA_OFFSET 5
> +
> +#define SPS30_SERIAL_START_MEAS 0x00
> +#define SPS30_SERIAL_STOP_MEAS 0x01
> +#define SPS30_SERIAL_READ_MEAS 0x03
> +#define SPS30_SERIAL_RESET 0xd3
> +#define SPS30_SERIAL_CLEAN_FAN 0x56
> +#define SPS30_SERIAL_PERIOD 0x80
> +#define SPS30_SERIAL_DEV_INFO 0xd0
> +#define SPS30_SERIAL_READ_VERSION 0xd1
> +
> +struct sps30_serial_priv {
> +	struct completion new_frame;
> +	unsigned char buf[SPS30_SERIAL_MAX_BUF_SIZE];
> +	size_t num;
> +	bool escaped;
> +	bool done;
> +};
> +
> +static int sps30_serial_xfer(struct sps30_state *state, const unsigned char *buf, size_t size)
> +{
> +	struct serdev_device *serdev = to_serdev_device(state->dev);
> +	struct sps30_serial_priv *priv = state->priv;
> +	int ret;
> +
> +	priv->num = 0;
> +	priv->escaped = false;
> +	priv->done = false;
> +
> +	ret = serdev_device_write(serdev, buf, size, SPS30_SERIAL_TIMEOUT);
> +	if (ret < 0)
> +		return ret;
> +	if (ret != size)
> +		return -EIO;
> +
> +	ret = wait_for_completion_interruptible_timeout(&priv->new_frame, SPS30_SERIAL_TIMEOUT);
> +	if (ret < 0)
> +		return ret;
> +	if (!ret)
> +		return -ETIMEDOUT;
> +
> +	return 0;
> +}
> +
> +static struct {
> +	unsigned char byte;
> +	unsigned char byte2;
> +} sps30_serial_bytes[] = {
> +	{ 0x11, 0x31 },
> +	{ 0x13, 0x33 },
> +	{ 0x7e, 0x5e },
> +	{ 0x7d, 0x5d },
> +};

const?

> +
> +static int sps30_serial_put_byte(unsigned char *buf, unsigned char byte)
> +{
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(sps30_serial_bytes); i++) {
> +		if (sps30_serial_bytes[i].byte != byte)
> +			continue;
> +
> +		buf[0] = SPS30_SERIAL_ESCAPE_CHAR;
> +		buf[1] = sps30_serial_bytes[i].byte2;
> +
> +		return 2;
> +	}
> +
> +	buf[0] = byte;
> +
> +	return 1;
> +}
> +
> +static char sps30_serial_get_byte(bool escaped, unsigned char byte2)
> +{
> +	int i;
> +
> +	if (!escaped)
> +		return byte2;
> +
> +	for (i = 0; i < ARRAY_SIZE(sps30_serial_bytes); i++) {
> +		if (sps30_serial_bytes[i].byte2 != byte2)
> +			continue;
> +
> +		return sps30_serial_bytes[i].byte;
> +	}
> +
> +	return 0;
> +}
> +
> +static unsigned char sps30_serial_calc_chksum(const unsigned char *buf, size_t num)
> +{
> +	unsigned int chksum = 0;
> +	size_t i;
> +
> +	for (i = 0; i < num; i++)
> +		chksum += buf[i];
> +
> +	return ~chksum;
> +}
> +
> +static int sps30_serial_prep_frame(unsigned char *buf, unsigned char cmd,
> +				   const unsigned char *arg, size_t arg_size)
> +{
> +	unsigned char chksum;
> +	int num = 0;
> +	size_t i;
> +
> +	buf[num++] = SPS30_SERIAL_SOF_EOF;
> +	buf[num++] = 0;
> +	num += sps30_serial_put_byte(buf + num, cmd);
> +	num += sps30_serial_put_byte(buf + num, arg_size);
> +
> +	for (i = 0; i < arg_size; i++)
> +		num += sps30_serial_put_byte(buf + num, arg[i]);
> +
> +	/* SOF isn't checksummed */
> +	chksum = sps30_serial_calc_chksum(buf + 1, num - 1);
> +	num += sps30_serial_put_byte(buf + num, chksum);
> +	buf[num++] = SPS30_SERIAL_SOF_EOF;
> +
> +	return num;
> +}
> +
> +static bool sps30_serial_frame_valid(struct sps30_state *state, const unsigned char *buf)
> +{
> +	struct sps30_serial_priv *priv = state->priv;
> +	unsigned char chksum;
> +
> +	if ((priv->num < SPS30_SERIAL_FRAME_MIN_SIZE) ||
> +	    (priv->num != SPS30_SERIAL_FRAME_MIN_SIZE +
> +	     priv->buf[SPS30_SERIAL_FRAME_MISO_LEN_OFFSET])) {
> +		dev_err(state->dev, "frame has invalid number of bytes\n");
> +		return false;
> +	}
> +
> +	if ((priv->buf[SPS30_SERIAL_FRAME_ADR_OFFSET] != buf[SPS30_SERIAL_FRAME_ADR_OFFSET]) ||
> +	    (priv->buf[SPS30_SERIAL_FRAME_CMD_OFFSET] != buf[SPS30_SERIAL_FRAME_CMD_OFFSET])) {
> +		dev_err(state->dev, "frame has wrong ADR and CMD bytes\n");
> +		return false;
> +	}
> +
> +	if (priv->buf[SPS30_SERIAL_FRAME_MISO_STATE_OFFSET]) {
> +		dev_err(state->dev, "frame with non-zero state received (0x%02x)\n",
> +			priv->buf[SPS30_SERIAL_FRAME_MISO_STATE_OFFSET]);
> +		return false;
> +	}
> +
> +	/* SOF, checksum and EOF are not checksummed */
> +	chksum = sps30_serial_calc_chksum(priv->buf + 1, priv->num - 3);
> +	if (priv->buf[priv->num - 2] != chksum) {
> +		dev_err(state->dev, "frame integrity check failed\n");
> +		return false;
> +	}
> +
> +	return true;
> +}
> +
> +static int sps30_serial_command(struct sps30_state *state, unsigned char cmd,
> +				const void *arg, size_t arg_size, void *rsp, size_t rsp_size)
> +{
> +	struct sps30_serial_priv *priv = state->priv;
> +	unsigned char buf[SPS30_SERIAL_MAX_BUF_SIZE];
> +	int ret, size;
> +
> +	size = sps30_serial_prep_frame(buf, cmd, arg, arg_size);
> +	ret = sps30_serial_xfer(state, buf, size);
> +	if (ret)
> +		return ret;
> +
> +	if (!sps30_serial_frame_valid(state, buf))
> +		return -EIO;
> +
> +	if (rsp) {
> +		rsp_size = min_t(size_t, priv->buf[SPS30_SERIAL_FRAME_MISO_LEN_OFFSET], rsp_size);
> +		memcpy(rsp, &priv->buf[SPS30_SERIAL_FRAME_MISO_DATA_OFFSET], rsp_size);
> +	}
> +
> +	return rsp_size;
> +}
> +
> +static int sps30_serial_receive_buf(struct serdev_device *serdev,
> +				    const unsigned char *buf, size_t size)
> +{
> +	struct iio_dev *indio_dev = dev_get_drvdata(&serdev->dev);
> +	struct sps30_serial_priv *priv;
> +	struct sps30_state *state;
> +	unsigned char byte;
> +	size_t i;
> +
> +	if (!indio_dev)
> +		return 0;
> +
> +	state = iio_priv(indio_dev);
> +	priv = state->priv;
> +
> +	/* just in case device put some unexpected data on the bus */
> +	if (priv->done)
> +		return size;
> +
> +	/* wait for the start of frame */
> +	if (!priv->num && size && buf[0] != SPS30_SERIAL_SOF_EOF)
> +		return 1;
> +
> +	if (priv->num + size >= ARRAY_SIZE(priv->buf))
> +		size = ARRAY_SIZE(priv->buf) - priv->num;
> +
> +	for (i = 0; i < size; i++) {
> +		byte = buf[i];
> +		/* remove stuffed bytes on-the-fly */
> +		if (byte == SPS30_SERIAL_ESCAPE_CHAR) {
> +			priv->escaped = true;
> +			continue;
> +		}
> +
> +		byte = sps30_serial_get_byte(priv->escaped, byte);
> +		if (priv->escaped && !byte)
> +			dev_warn(state->dev, "unrecognized escaped char (0x%02x)\n", byte);
> +
> +		priv->buf[priv->num++] = byte;
> +
> +		/* EOF received */
> +		if (!priv->escaped && byte == SPS30_SERIAL_SOF_EOF) {
> +			if (priv->num < SPS30_SERIAL_FRAME_MIN_SIZE)
> +				continue;
> +
> +			priv->done = true;
> +			complete(&priv->new_frame);
> +			i++;
> +			break;
> +		}
> +
> +		priv->escaped = false;
> +	}
> +
> +	return i;
> +}
> +
> +static const struct serdev_device_ops sps30_serial_device_ops = {
> +	.receive_buf = sps30_serial_receive_buf,
> +	.write_wakeup = serdev_device_write_wakeup,
> +};
> +
> +static int sps30_serial_start_meas(struct sps30_state *state)
> +{
> +	/* request BE IEEE754 formatted data */
> +	unsigned char buf[] = { 0x01, 0x03 };
> +
> +	return sps30_serial_command(state, SPS30_SERIAL_START_MEAS, buf, sizeof(buf), NULL, 0);
> +}
> +
> +static int sps30_serial_stop_meas(struct sps30_state *state)
> +{
> +	return sps30_serial_command(state, SPS30_SERIAL_STOP_MEAS, NULL, 0, NULL, 0);
> +}
> +
> +static int sps30_serial_reset(struct sps30_state *state)
> +{
> +	int ret;
> +
> +	ret = sps30_serial_command(state, SPS30_SERIAL_RESET, NULL, 0, NULL, 0);
> +	msleep(500);
> +
> +	return ret;
> +}
> +
> +static int sps30_serial_read_meas(struct sps30_state *state, __be32 *meas, size_t num)
> +{
> +	int ret;
> +
> +	/* measurements are ready within a second */
> +	if (msleep_interruptible(1000))
> +		return -EINTR;
> +
> +	ret = sps30_serial_command(state, SPS30_SERIAL_READ_MEAS, NULL, 0, meas, num * sizeof(num));
> +	if (ret < 0)
> +		return ret;
> +	/* if measurements aren't ready sensor returns empty frame */
> +	if (ret == SPS30_SERIAL_FRAME_MIN_SIZE)
> +		return -ETIMEDOUT;
> +	if (ret != num * sizeof(*meas))
> +		return -EIO;
> +
> +	return 0;
> +}
> +
> +static int sps30_serial_clean_fan(struct sps30_state *state)
> +{
> +	return sps30_serial_command(state, SPS30_SERIAL_CLEAN_FAN, NULL, 0, NULL, 0);
> +}
> +
> +static int sps30_serial_read_cleaning_period(struct sps30_state *state, __be32 *period)
> +{
> +	unsigned char buf[] = { 0x00 };
> +	int ret;
> +
> +	ret = sps30_serial_command(state, SPS30_SERIAL_PERIOD, buf, sizeof(buf),
> +				   period, sizeof(*period));
> +	if (ret < 0)
> +		return ret;
> +	if (ret != sizeof(*period))
> +		return -EIO;
> +
> +	return 0;
> +}
> +
> +static int sps30_serial_write_cleaning_period(struct sps30_state *state, __be32 period)
> +{
> +	unsigned char buf[5] = { 0x00 };
> +
> +	memcpy(buf + 1, &period, sizeof(period));
> +
> +	return sps30_serial_command(state, SPS30_SERIAL_PERIOD, buf, sizeof(buf), NULL, 0);
> +}
> +
> +static int sps30_serial_show_info(struct sps30_state *state)
> +{
> +	/* extra nul byte just in case serial number isn't a valid string */
> +	unsigned char buf[32 + 1] = { 0x00 };
> +	struct device *dev = state->dev;
> +	int ret;
> +
> +	/* tell device to return serial number */
> +	buf[0] = 0x03;

Bit odd when you just set it to 0 above.  Maybe just set 
	unsigned char buf[32 + 1] = { 0x03 }; and combine the comments?

If everything else is fine, I can do that whilst applying.

> +	ret = sps30_serial_command(state, SPS30_SERIAL_DEV_INFO, buf, 1, buf, sizeof(buf) - 1);
> +	if (ret < 0)
> +		return ret;
> +
> +	dev_info(dev, "serial number: %s\n", buf);
> +
> +	ret = sps30_serial_command(state, SPS30_SERIAL_READ_VERSION, NULL, 0, buf, sizeof(buf) - 1);
> +	if (ret < 0)
> +		return ret;
> +	if (ret < 2)
> +		return -EIO;
> +
> +	dev_info(dev, "fw version: %u.%u\n", buf[0], buf[1]);
> +
> +	return 0;
> +}
> +
> +static const struct sps30_ops sps30_serial_ops = {
> +	.start_meas = sps30_serial_start_meas,
> +	.stop_meas = sps30_serial_stop_meas,
> +	.read_meas = sps30_serial_read_meas,
> +	.reset = sps30_serial_reset,
> +	.clean_fan = sps30_serial_clean_fan,
> +	.read_cleaning_period = sps30_serial_read_cleaning_period,
> +	.write_cleaning_period = sps30_serial_write_cleaning_period,
> +	.show_info = sps30_serial_show_info,
> +};
> +
> +static int sps30_serial_probe(struct serdev_device *serdev)
> +{
> +	struct device *dev = &serdev->dev;
> +	struct sps30_serial_priv *priv;
> +	int ret;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	init_completion(&priv->new_frame);
> +	serdev_device_set_client_ops(serdev, &sps30_serial_device_ops);
> +
> +	ret = devm_serdev_device_open(dev, serdev);
> +	if (ret)
> +		return ret;
> +
> +	serdev_device_set_baudrate(serdev, 115200);
> +	serdev_device_set_flow_control(serdev, false);
> +
> +	ret = serdev_device_set_parity(serdev, SERDEV_PARITY_NONE);
> +	if (ret)
> +		return ret;
> +
> +	return sps30_probe(dev, SPS30_SERIAL_DEV_NAME, priv, &sps30_serial_ops);
> +}
> +
> +static const struct of_device_id sps30_serial_of_match[] = {
> +	{ .compatible = "sensirion,sps30" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, sps30_serial_of_match);
> +
> +static struct serdev_device_driver sps30_serial_driver = {
> +	.driver = {
> +		.name = KBUILD_MODNAME,
> +		.of_match_table = sps30_serial_of_match,
> +	},
> +	.probe = sps30_serial_probe,
> +};
> +module_serdev_device_driver(sps30_serial_driver);
> +
> +MODULE_AUTHOR("Tomasz Duszynski <tomasz.duszynski@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Sensirion SPS30 particulate matter sensor serial driver");
> +MODULE_LICENSE("GPL v2");




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux