When buffered sampling is enabled, the accelerometer will dump data into
the internal fifo and interrupt at watermark. Then the driver flushes
all data to the iio buffer.
As the accelerometer doesn't have internal timestamps, they are aproximated
between to interrupts.
Signed-off-by: Sean Nyekjaer <sean@xxxxxxxxxx>
---
This series depends on "iio: accel: add support for
FXLS8962AF/FXLS8964AF accelerometers"
Any good pratice in general to how much to fill the fifo?
The accelerometer a internal buffer with 32 samples and I have set the watermark to 16.
drivers/iio/accel/fxls8962af-core.c | 215 +++++++++++++++++++++++++++-
1 file changed, 214 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
index 848f3d68f5d4..2bd5c6d76b63 100644
--- a/drivers/iio/accel/fxls8962af-core.c
+++ b/drivers/iio/accel/fxls8962af-core.c
@@ -20,13 +20,17 @@
#include <linux/regulator/consumer.h>
#include <linux/regmap.h>
+#include <linux/iio/buffer.h>
#include <linux/iio/iio.h>
+#include <linux/iio/kfifo_buf.h>
#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
#include "fxls8962af.h"
#define FXLS8962AF_INT_STATUS 0x00
#define FXLS8962AF_INT_STATUS_SRC_BOOT BIT(0)
+#define FXLS8962AF_INT_STATUS_SRC_BUF BIT(5)
#define FXLS8962AF_INT_STATUS_SRC_DRDY BIT(7)
#define FXLS8962AF_TEMP_OUT 0x01
#define FXLS8962AF_VECM_LSB 0x02
@@ -34,6 +38,9 @@
#define FXLS8962AF_OUT_Y_LSB 0x06
#define FXLS8962AF_OUT_Z_LSB 0x08
#define FXLS8962AF_BUF_STATUS 0x0b
+#define FXLS8962AF_BUF_STATUS_BUF_CNT GENMASK(5, 0)
+#define FXLS8962AF_BUF_STATUS_BUF_OVF BIT(6)
+#define FXLS8962AF_BUF_STATUS_BUF_WMRK BIT(7)
#define FXLS8962AF_BUF_X_LSB 0x0c
#define FXLS8962AF_BUF_Y_LSB 0x0e
#define FXLS8962AF_BUF_Z_LSB 0x10
@@ -66,6 +73,7 @@
#define FXLS8962AF_ASLP_COUNT_LSB 0x1e
#define FXLS8962AF_INT_EN 0x20
+#define FXLS8962AF_INT_EN_BUF_EN BIT(6)
#define FXLS8962AF_INT_PIN_SEL 0x21
#define FXLS8962AF_INT_PIN_SEL_MASK GENMASK(7, 0)
#define FXLS8962AF_INT_PIN_SEL_INT1 0x00
@@ -76,7 +84,10 @@
#define FXLS8962AF_OFF_Z 0x24
#define FXLS8962AF_BUF_CONFIG1 0x26
+#define FXLS8962AF_BC1_BUF_MODE_MASK GENMASK(6, 5)
+#define FXLS8962AF_BC1_BUF_MODE_PREP(x) FIELD_PREP(FXLS8962AF_BC1_BUF_MODE_MASK, x)
#define FXLS8962AF_BUF_CONFIG2 0x27
+#define FXLS8962AF_BUF_CONFIG2_BUF_WMRK GENMASK(5, 0)
#define FXLS8962AF_ORIENT_STATUS 0x28
#define FXLS8962AF_ORIENT_CONFIG 0x29
@@ -106,6 +117,7 @@
#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS 2000
+#define FXLS8962AF_FIFO_LENGTH 32
#define FXLS8962AF_SCALE_TABLE_LEN 4
#define FXLS8962AF_SAMP_FREQ_TABLE_LEN 13
@@ -133,6 +145,11 @@ struct fxls8962af_data {
struct regmap *regmap;
const struct fxls8962af_chip_info *chip_info;
struct regulator *vdd_reg;
+ struct {
+ __le16 channels[3];
+ s64 ts __aligned(8);
+ } scan;
+ int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
struct iio_mount_matrix orientation;
};
@@ -433,7 +450,10 @@ static int fxls8962af_read_raw(struct iio_dev *indio_dev,
ret = fxls8962af_get_temp(data, val);
break;
case IIO_ACCEL:
- ret = fxls8962af_get_axis(data, chan, val);
+ if (iio_buffer_enabled(indio_dev))
+ ret = -EBUSY;
+ else
+ ret = fxls8962af_get_axis(data, chan, val);
break;
default:
ret = -EINVAL;
@@ -572,6 +592,174 @@ static int fxls8962af_reset(struct fxls8962af_data *data)
return ret;
}
+static int fxls8962af_fifo_set_mode(struct fxls8962af_data *data, bool onoff)
+{
+ int ret;
+
+ ret = regmap_update_bits(data->regmap, FXLS8962AF_BUF_CONFIG1,
+ FXLS8962AF_BC1_BUF_MODE_MASK,
+ FXLS8962AF_BC1_BUF_MODE_PREP(onoff));
+
+ return ret;
+}
+
+
+static int fxls8962af_buffer_preenable(struct iio_dev *indio_dev)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+
+ return fxls8962af_power_on(data);
+}
+
+static int fxls8962af_buffer_postenable(struct iio_dev *indio_dev)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+ int ret = 0;
+
+ if (indio_dev->currentmode == INDIO_BUFFER_TRIGGERED)
+ return 0;
+
+ fxls8962af_standby(data);
+
+ /* Enable buffer interrupt*/
+ ret = regmap_update_bits(data->regmap, FXLS8962AF_INT_EN,
+ FXLS8962AF_INT_EN_BUF_EN,
+ FXLS8962AF_INT_EN_BUF_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Enable watermark at max fifo size*/
+ ret = regmap_update_bits(data->regmap, FXLS8962AF_BUF_CONFIG2,
+ FXLS8962AF_BUF_CONFIG2_BUF_WMRK,
+ FXLS8962AF_BUF_CONFIG2_BUF_WMRK / 2);
+ if (ret < 0)
+ return ret;
+
+ ret = fxls8962af_fifo_set_mode(data, true);
+
+ fxls8962af_active(data);
+
+ return ret;
+}
+
+static int fxls8962af_buffer_predisable(struct iio_dev *indio_dev)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+ int ret = 0;
+
+ if (indio_dev->currentmode == INDIO_BUFFER_TRIGGERED)
+ return 0;
+
+ fxls8962af_standby(data);
+
+ /* Disable buffer interrupt*/
+ ret = regmap_update_bits(data->regmap, FXLS8962AF_INT_EN,
+ FXLS8962AF_INT_EN_BUF_EN, 0);
+ if (ret < 0)
+ return ret;
+
+ fxls8962af_fifo_set_mode(data, false);
+
+ fxls8962af_active(data);
+
+ return 0;
+}
+
+static int fxls8962af_buffer_postdisable(struct iio_dev *indio_dev)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+
+ return fxls8962af_power_off(data);
+}
+
+static const struct iio_buffer_setup_ops fxls8962af_buffer_ops = {
+ .preenable = fxls8962af_buffer_preenable,
+ .postenable = fxls8962af_buffer_postenable,
+ .predisable = fxls8962af_buffer_predisable,
+ .postdisable = fxls8962af_buffer_postdisable,
+};
+
+static int fxls8962af_fifo_transfer(struct fxls8962af_data *data,
+ char *buffer, int samples)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ int sample_length = 3 * 2;
+ int ret;
+ int total_length = samples * sample_length;
+
+ ret = regmap_raw_read(data->regmap, FXLS8962AF_BUF_X_LSB, buffer,
+ total_length);
+ if (ret < 0)
+ dev_err(dev, "Error transferring data from fifo: %d\n", ret);
+
+ return ret;
+}
+
+static int fxls8962af_fifo_flush(struct iio_dev *indio_dev)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+ struct device *dev = regmap_get_device(data->regmap);
+ u16 buffer[FXLS8962AF_FIFO_LENGTH * 3];
+ uint64_t sample_period;
+ unsigned int reg;
+ int64_t tstamp;
+ int ret, i;
+ u8 count;
+
+ ret = regmap_read(data->regmap, FXLS8962AF_BUF_STATUS, ®);
+ if (ret < 0)
+ return ret;
+
+ if (reg & FXLS8962AF_BUF_STATUS_BUF_OVF) {
+ dev_err(dev, "Buffer overflown");
+ return -1;
+ }
+
+ count = reg & FXLS8962AF_BUF_STATUS_BUF_CNT;
+
+ if (!count)
+ return 0;
+
+ data->old_timestamp = data->timestamp;
+ data->timestamp = iio_get_time_ns(indio_dev);
+
+ /* Approximate timestamps for each of the sample based on the sampling,
+ * frequency, timestamp for last sample and number of samples.
+ */
+ sample_period = (data->timestamp - data->old_timestamp);
+ do_div(sample_period, count);
+ tstamp = data->timestamp - (count - 1) * sample_period;
+
+
+ ret = fxls8962af_fifo_transfer(data, (u8 *)buffer, count);
+ if (ret)
+ return ret;
+
+ /*
+ * Ideally we want the IIO core to handle the demux when running in fifo
+ * mode but not when running in triggered buffer mode. Unfortunately
+ * this does not seem to be possible, so stick with driver demux for
+ * now.
+ */
+ for (i = 0; i < count; i++) {
+ int j, bit;
+
+ j = 0;
+ for_each_set_bit(bit, indio_dev->active_scan_mask,
+ indio_dev->masklength) {
+ memcpy(&data->scan.channels[j++], &buffer[i * 3 + bit],
+ sizeof(data->scan.channels[0]));
+ }
+
+ iio_push_to_buffers_with_timestamp(indio_dev, &data->scan,
+ tstamp);
+
+ tstamp += sample_period;
+ }
+
+ return count;
+}
+
static irqreturn_t fxls8962af_interrupt(int irq, void *p)
{
struct iio_dev *indio_dev = p;
@@ -583,9 +771,32 @@ static irqreturn_t fxls8962af_interrupt(int irq, void *p)
if (ret < 0)
return IRQ_NONE;
+ if (reg & FXLS8962AF_INT_STATUS_SRC_BUF) {
+ ret = fxls8962af_fifo_flush(indio_dev);
+ if (ret < 0)
+ return IRQ_NONE;
+
+ return IRQ_HANDLED;
+ }
+
return IRQ_NONE;
}
+static int fxls8962af_fifo_setup(struct iio_dev *indio_dev)
+{
+ struct iio_buffer *buffer;
+
+ buffer = devm_iio_kfifo_allocate(&indio_dev->dev);
+ if (!buffer)
+ return -ENOMEM;
+
+ iio_device_attach_buffer(indio_dev, buffer);
+ indio_dev->modes |= INDIO_BUFFER_SOFTWARE;
+ indio_dev->setup_ops = &fxls8962af_buffer_ops;
+
+ return 0;
+}
+
static void fxls8962af_regulator_disable(void *data_ptr)
{
struct fxls8962af_data *data = data_ptr;
@@ -751,6 +962,8 @@ int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
ret = fxls8962af_irq_setup(indio_dev, irq);
if (ret < 0)
return ret;
+
+ fxls8962af_fifo_setup(indio_dev);
}
ret = pm_runtime_set_active(dev);
--
2.31.0
