Add bindings for thermal monitor, part of Qualcomm PMIC5 chips. It is a close counterpart of VADC part of those PMICs. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> --- .../bindings/thermal/qcom-spmi-adc-tm5.yaml | 154 ++++++++++++++++++ 1 file changed, 154 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml new file mode 100644 index 000000000000..9da2b349030d --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm5.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's SPMI PMIC ADC Thermal Monitoring +maintainers: + - Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx> + +properties: + compatible: + const: qcom,spmi-adc-tm5 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + description: + Number of cells required to uniquely identify the thermal sensors. Since + we have multiple sensors this is set to 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + qcom,avg-samples: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of samples to be used for measurement. + enum: + - 1 + - 2 + - 4 + - 8 + - 16 + default: 1 + + qcom,decimation: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This parameter is used to decrease ADC sampling rate. + Quicker measurements can be made by reducing decimation ratio. + enum: + - 250 + - 420 + - 840 + default: 840 + +patternProperties: + "^([-a-z0-9]*)@[0-7]$": + type: object + description: + Represent one thermal sensor. + + properties: + reg: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM + minimum: 0 + maximum: 7 + + io-channels: + description: + From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor + + qcom,ratiometric: + $ref: /schemas/types.yaml#/definitions/flag + description: + Channel calibration type. + If this property is specified VADC will use the VDD reference + (1.875V) and GND for channel calibration. If property is not found, + channel will be calibrated with 0V and 1.25V reference channels, + also known as absolute calibration. + + qcom,hw-settle-time-us: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Time between AMUX getting configured and the ADC starting conversion. + enum: [15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 8000, 16000, 32000, 64000, 128000] + + qcom,pre-scaling: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: Used for scaling the channel input signal before the + signal is fed to VADC. The configuration for this node is to know the + pre-determined ratio and use it for post scaling. It is a pair of + integers, denoting the numerator and denominator of the fraction by + which input signal is multiplied. For example, <1 3> indicates the + signal is scaled down to 1/3 of its value before ADC measurement. If + property is not found default value depending on chip will be used. + items: + - const: 1 + - enum: [ 1, 3, 4, 6, 20, 8, 10 ] + + required: + - reg + - io-channels + + additionalProperties: + false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + - "#thermal-sensor-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/qcom,spmi-vadc.h> + #include <dt-bindings/interrupt-controller/irq.h> + spmi_bus { + #address-cells = <1>; + #size-cells = <0>; + pm8150b_adc: adc@3100 { + reg = <0x3100>; + compatible = "qcom,spmi-adc5"; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + io-channel-ranges; + + /* Other propreties are omitted */ + conn-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + }; + + pm8150b_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + conn-therm@0 { + reg = <0>; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + }; + }; +... -- 2.28.0
