From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> There are no remaining light drivers in staging/iio. The content of this file are either included in the non staging ABI docs, or don't seem to be used in any current driver. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> --- .../iio/Documentation/sysfs-bus-iio-light | 79 ------------------- 1 file changed, 79 deletions(-) diff --git a/drivers/staging/iio/Documentation/sysfs-bus-iio-light b/drivers/staging/iio/Documentation/sysfs-bus-iio-light deleted file mode 100644 index 7c7cd8456060..000000000000 --- a/drivers/staging/iio/Documentation/sysfs-bus-iio-light +++ /dev/null @@ -1,79 +0,0 @@ -What: /sys/bus/iio/devices/device[n]/in_illuminance0[_input|_raw] -KernelVersion: 2.6.35 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This should return the calculated lux from the light sensor. If - it comes back in SI units, it should also include _input else it - should include _raw to signify it is not in SI units. - -What: /sys/.../device[n]/proximity_on_chip_ambient_infrared_suppression -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - Hardware dependent mode for an ALS device to calculate the value - in proximity mode. When this is enabled, then the device should - use a infrared sensor reading to remove infrared noise from the - proximity reading. If this is not enabled, the driver can still - do this calculation manually by reading the infrared sensor - value and doing the negation in sw. - -What: /sys/bus/iio/devices/device[n]/in_proximity[_input|_raw] -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property is supported by proximity sensors and should be - used to return the value of a reading by the sensor. If this - value is returned in SI units, it should also include _input - but if it is not, then it should include _raw. - -What: /sys/bus/iio/devices/device[n]/intensity_infrared[_input|_raw] -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property is supported by sensors that have an infrared - sensing mode. This value should be the output from a reading - and if expressed in SI units, should include _input. If this - value is not in SI units, then it should include _raw. - -What: /sys/bus/iio/devices/device[n]/in_illuminance0_target -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property gets/sets the last known external - lux measurement used in/for calibration. - -What: /sys/bus/iio/devices/device[n]/in_illuminance0_integration_time -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property gets/sets the sensors ADC analog integration time. - -What: /sys/bus/iio/devices/device[n]/in_illuminance0_lux_table -KernelVersion: 2.6.37 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property gets/sets the table of coefficients - used in calculating illuminance in lux. - -What: /sys/bus/iio/devices/device[n]/in_intensity_clear[_input|_raw] -What: /sys/bus/iio/devices/device[n]/in_intensity_red[_input|_raw] -What: /sys/bus/iio/devices/device[n]/in_intensity_green[_input|_raw] -What: /sys/bus/iio/devices/device[n]/in_intensity_blue[_input|_raw] -KernelVersion: 3.6.0 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This property is supported by sensors that have a RGBC - sensing mode. This value should be the output from a reading - and if expressed in SI units, should include _input. If this - value is not in SI units (irradiance, uW/mm^2), then it should - include _raw. - -What: /sys/bus/iio/devices/device[n]/in_cct0[_input|_raw] -KernelVersion: 3.6.0 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - This should return the correlated color temperature from the - light sensor. If it comes back in SI units, it should also - include _input else it should include _raw to signify it is not - in SI units. - -- 2.28.0
