The SADC component in JZ47xx SoCs provides support for touchscreen
operations (pen position and pen down pressure) in single-ended and
differential modes.
Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
utilize the touchscreen mode by having their joystick(s) attached to the
X/Y positive/negative input pins.
GCW Zero comes with a single joystick and is sufficiently handled with the
currently implemented single-ended mode. Support for boards with two
joysticks, where one is hooked up to Xn/Yn and the other to Xp/Yp channels
will need to be provided in the future.
The touchscreen component of SADC takes a significant time to stabilize
after first receiving the clock and a delay of 50ms has been empirically
proven to be a safe value before data sampling can begin.
All the boards which probe this driver have the interrupt provided from
devicetree, with no need to handle a case where the irq was not provided.
Signed-off-by: Artur Rojek <contact@xxxxxxxxxxxxxx>
Tested-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
---
Changes:
v2: - improve description of the touchscreen mode,
- get rid of the unneeded kfifo,
- drop IIO_BUFFER_CB from Kconfig,
- remove extended names from the touchscreen channels
v3: remove unneeded `linux/iio/kfifo_buf.h` include
v4: clarify irq provider source in the patch description
v5: no change
drivers/iio/adc/Kconfig | 1 +
drivers/iio/adc/ingenic-adc.c | 109 +++++++++++++++++++++++++++++++++-
2 files changed, 108 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 82e33082958c..d3fd4b6e2d47 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -453,6 +453,7 @@ config INA2XX_ADC
config INGENIC_ADC
tristate "Ingenic JZ47xx SoCs ADC driver"
depends on MIPS || COMPILE_TEST
+ select IIO_BUFFER
help
Say yes here to build support for the Ingenic JZ47xx SoCs ADC unit.
diff --git a/drivers/iio/adc/ingenic-adc.c b/drivers/iio/adc/ingenic-adc.c
index 7a24bc1dabe1..0dafc8d5d0d8 100644
--- a/drivers/iio/adc/ingenic-adc.c
+++ b/drivers/iio/adc/ingenic-adc.c
@@ -8,7 +8,9 @@
#include <dt-bindings/iio/adc/ingenic,adc.h>
#include <linux/clk.h>
+#include <linux/iio/buffer.h>
#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
@@ -20,6 +22,8 @@
#define JZ_ADC_REG_CFG 0x04
#define JZ_ADC_REG_CTRL 0x08
#define JZ_ADC_REG_STATUS 0x0c
+#define JZ_ADC_REG_ADSAME 0x10
+#define JZ_ADC_REG_ADWAIT 0x14
#define JZ_ADC_REG_ADTCH 0x18
#define JZ_ADC_REG_ADBDAT 0x1c
#define JZ_ADC_REG_ADSDAT 0x20
@@ -28,6 +32,9 @@
#define JZ_ADC_REG_ENABLE_PD BIT(7)
#define JZ_ADC_REG_CFG_AUX_MD (BIT(0) | BIT(1))
#define JZ_ADC_REG_CFG_BAT_MD BIT(4)
+#define JZ_ADC_REG_CFG_PULL_UP(n) ((n) << 16)
+#define JZ_ADC_REG_CFG_SAMPLE_NUM(n) ((n) << 10)
+#define JZ_ADC_REG_CFG_TOUCH_OPS_MASK (BIT(31) | GENMASK(23, 10))
#define JZ_ADC_REG_ADCLK_CLKDIV_LSB 0
#define JZ4725B_ADC_REG_ADCLK_CLKDIV10US_LSB 16
#define JZ4770_ADC_REG_ADCLK_CLKDIV10US_LSB 8
@@ -44,6 +51,14 @@
#define JZ4770_ADC_BATTERY_VREF 6600
#define JZ4770_ADC_BATTERY_VREF_BITS 12
+#define JZ_ADC_IRQ_AUX BIT(0)
+#define JZ_ADC_IRQ_BATTERY BIT(1)
+#define JZ_ADC_IRQ_TOUCH BIT(2)
+#define JZ_ADC_IRQ_PEN_DOWN BIT(3)
+#define JZ_ADC_IRQ_PEN_UP BIT(4)
+#define JZ_ADC_IRQ_PEN_DOWN_SLEEP BIT(5)
+#define JZ_ADC_IRQ_SLEEP BIT(7)
+
struct ingenic_adc;
struct ingenic_adc_soc_data {
@@ -411,6 +426,28 @@ static const struct iio_info ingenic_adc_info = {
};
static const struct iio_chan_spec ingenic_channels[] = {
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_XP,
+ .scan_index = 0,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16
+ },
+ },
+ {
+ .type = IIO_POSITIONRELATIVE,
+ .indexed = 1,
+ .channel = INGENIC_ADC_TOUCH_YP,
+ .scan_index = 1,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 12,
+ .storagebits = 16
+ },
+ },
{
.extend_name = "aux",
.type = IIO_VOLTAGE,
@@ -418,6 +455,7 @@ static const struct iio_chan_spec ingenic_channels[] = {
BIT(IIO_CHAN_INFO_SCALE),
.indexed = 1,
.channel = INGENIC_ADC_AUX,
+ .scan_index = -1
},
{
.extend_name = "battery",
@@ -428,6 +466,7 @@ static const struct iio_chan_spec ingenic_channels[] = {
BIT(IIO_CHAN_INFO_SCALE),
.indexed = 1,
.channel = INGENIC_ADC_BATTERY,
+ .scan_index = -1
},
{ /* Must always be last in the array. */
.extend_name = "aux2",
@@ -436,16 +475,69 @@ static const struct iio_chan_spec ingenic_channels[] = {
BIT(IIO_CHAN_INFO_SCALE),
.indexed = 1,
.channel = INGENIC_ADC_AUX2,
+ .scan_index = -1
},
};
+static int ingenic_adc_buffer_enable(struct iio_dev *iio_dev)
+{
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+
+ clk_enable(adc->clk);
+ /* It takes significant time for the touchscreen hw to stabilize. */
+ msleep(50);
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_TOUCH_OPS_MASK,
+ JZ_ADC_REG_CFG_SAMPLE_NUM(4) |
+ JZ_ADC_REG_CFG_PULL_UP(4));
+ writew(80, adc->base + JZ_ADC_REG_ADWAIT);
+ writew(2, adc->base + JZ_ADC_REG_ADSAME);
+ writeb((u8)~JZ_ADC_IRQ_TOUCH, adc->base + JZ_ADC_REG_CTRL);
+ writel(0, adc->base + JZ_ADC_REG_ADTCH);
+ ingenic_adc_enable(adc, 2, true);
+
+ return 0;
+}
+
+static int ingenic_adc_buffer_disable(struct iio_dev *iio_dev)
+{
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+
+ ingenic_adc_enable(adc, 2, false);
+ writeb(0xff, adc->base + JZ_ADC_REG_CTRL);
+ writeb(0xff, adc->base + JZ_ADC_REG_STATUS);
+ ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_TOUCH_OPS_MASK, 0);
+ writew(0, adc->base + JZ_ADC_REG_ADSAME);
+ writew(0, adc->base + JZ_ADC_REG_ADWAIT);
+ clk_disable(adc->clk);
+
+ return 0;
+}
+
+static const struct iio_buffer_setup_ops ingenic_buffer_setup_ops = {
+ .postenable = &ingenic_adc_buffer_enable,
+ .predisable = &ingenic_adc_buffer_disable
+};
+
+static irqreturn_t ingenic_adc_irq(int irq, void *data)
+{
+ struct iio_dev *iio_dev = data;
+ struct ingenic_adc *adc = iio_priv(iio_dev);
+ u32 tdat;
+
+ tdat = readl(adc->base + JZ_ADC_REG_ADTCH);
+ iio_push_to_buffers(iio_dev, &tdat);
+ writeb(JZ_ADC_IRQ_TOUCH, adc->base + JZ_ADC_REG_STATUS);
+
+ return IRQ_HANDLED;
+}
+
static int ingenic_adc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct iio_dev *iio_dev;
struct ingenic_adc *adc;
const struct ingenic_adc_soc_data *soc_data;
- int ret;
+ int irq, ret;
soc_data = device_get_match_data(dev);
if (!soc_data)
@@ -460,6 +552,18 @@ static int ingenic_adc_probe(struct platform_device *pdev)
mutex_init(&adc->aux_lock);
adc->soc_data = soc_data;
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "Failed to get irq: %d\n", irq);
+ return irq;
+ }
+ ret = devm_request_irq(dev, irq, ingenic_adc_irq, 0,
+ dev_name(dev), iio_dev);
+ if (ret < 0) {
+ dev_err(dev, "Failed to request irq: %d\n", ret);
+ return ret;
+ }
+
adc->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(adc->base))
return PTR_ERR(adc->base);
@@ -499,7 +603,8 @@ static int ingenic_adc_probe(struct platform_device *pdev)
iio_dev->dev.parent = dev;
iio_dev->name = "jz-adc";
- iio_dev->modes = INDIO_DIRECT_MODE;
+ iio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
+ iio_dev->setup_ops = &ingenic_buffer_setup_ops;
iio_dev->channels = ingenic_channels;
iio_dev->num_channels = ARRAY_SIZE(ingenic_channels);
/* Remove AUX2 from the list of supported channels. */
--
2.26.0
