Add helper functions to use the i2c auxiliary bus with the MPU i2c
master block.
Support only register based chip, reading and 1 byte writing. These
will be useful for initializing magnetometers inside MPU9x50 chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@xxxxxxxxxxxxxx>
---
drivers/iio/imu/inv_mpu6050/Makefile | 3 +-
drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c | 184 ++++++++++++++++++++++
drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h | 46 ++++++
3 files changed, 232 insertions(+), 1 deletion(-)
create mode 100644 drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c
create mode 100644 drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h
diff --git a/drivers/iio/imu/inv_mpu6050/Makefile b/drivers/iio/imu/inv_mpu6050/Makefile
index 33bec09fee9b..2cfbd926522f 100644
--- a/drivers/iio/imu/inv_mpu6050/Makefile
+++ b/drivers/iio/imu/inv_mpu6050/Makefile
@@ -4,7 +4,8 @@
#
obj-$(CONFIG_INV_MPU6050_IIO) += inv-mpu6050.o
-inv-mpu6050-y := inv_mpu_core.o inv_mpu_ring.o inv_mpu_trigger.o
+inv-mpu6050-y := inv_mpu_core.o inv_mpu_ring.o inv_mpu_trigger.o \
+ inv_mpu_aux.o
obj-$(CONFIG_INV_MPU6050_I2C) += inv-mpu6050-i2c.o
inv-mpu6050-i2c-y := inv_mpu_i2c.o inv_mpu_acpi.o
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c
new file mode 100644
index 000000000000..b4907c1a8bb6
--- /dev/null
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.c
@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 TDK-InvenSense, Inc.
+ */
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/delay.h>
+
+#include "inv_mpu_iio.h"
+
+/*
+ * i2c master auxiliary bus transfer function.
+ * Requires the i2c operations to be correctly setup before.
+ */
+static int inv_mpu_i2c_master_xfer(const struct inv_mpu6050_state *st)
+{
+ /* use 50hz frequency for xfer */
+ const unsigned int freq = 50;
+ const unsigned int period_ms = 1000 / freq;
+ uint8_t d;
+ unsigned int user_ctrl;
+ int ret;
+
+ /* set sample rate */
+ d = INV_MPU6050_FIFO_RATE_TO_DIVIDER(freq);
+ ret = regmap_write(st->map, st->reg->sample_rate_div, d);
+ if (ret)
+ return ret;
+
+ /* start i2c master */
+ user_ctrl = st->chip_config.user_ctrl | INV_MPU6050_BIT_I2C_MST_EN;
+ ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl);
+ if (ret)
+ goto error_restore_rate;
+
+ /* wait for xfer: 1 period + half-period margin */
+ msleep(period_ms + period_ms / 2);
+
+ /* stop i2c master */
+ user_ctrl = st->chip_config.user_ctrl;
+ ret = regmap_write(st->map, st->reg->user_ctrl, user_ctrl);
+ if (ret)
+ goto error_stop_i2c;
+
+ /* restore sample rate */
+ d = st->chip_config.divider;
+ ret = regmap_write(st->map, st->reg->sample_rate_div, d);
+ if (ret)
+ goto error_restore_rate;
+
+ return 0;
+
+error_stop_i2c:
+ regmap_write(st->map, st->reg->user_ctrl, st->chip_config.user_ctrl);
+error_restore_rate:
+ regmap_write(st->map, st->reg->sample_rate_div, st->chip_config.divider);
+ return ret;
+}
+
+int inv_mpu_aux_init(const struct inv_mpu6050_state *st)
+{
+ unsigned int val;
+ int ret;
+
+ /* configure i2c master */
+ val = INV_MPU6050_BITS_I2C_MST_CLK_400KHZ |
+ INV_MPU6050_BIT_WAIT_FOR_ES;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_MST_CTRL, val);
+ if (ret)
+ return ret;
+
+ /* configure i2c master delay */
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV4_CTRL, 0);
+ if (ret)
+ return ret;
+
+ val = INV_MPU6050_BIT_I2C_SLV0_DLY_EN |
+ INV_MPU6050_BIT_I2C_SLV1_DLY_EN |
+ INV_MPU6050_BIT_I2C_SLV2_DLY_EN |
+ INV_MPU6050_BIT_I2C_SLV3_DLY_EN |
+ INV_MPU6050_BIT_DELAY_ES_SHADOW;
+ return regmap_write(st->map, INV_MPU6050_REG_I2C_MST_DELAY_CTRL, val);
+}
+
+/*
+ * i2c slave reading using SLV0
+ */
+int inv_mpu_aux_read(const struct inv_mpu6050_state *st, uint8_t addr,
+ uint8_t reg, uint8_t *val, size_t size)
+{
+ unsigned int status;
+ int ret;
+
+ if (size > 0x0F)
+ return -EINVAL;
+
+ /* setup i2c SLV0 control: i2c addr, register, enable + size */
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(0),
+ INV_MPU6050_BIT_I2C_SLV_RNW | addr);
+ if (ret)
+ return ret;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(0), reg);
+ if (ret)
+ return ret;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0),
+ INV_MPU6050_BIT_SLV_EN | size);
+ if (ret)
+ return ret;
+
+ /* do i2c xfer */
+ ret = inv_mpu_i2c_master_xfer(st);
+ if (ret)
+ goto error_disable_i2c;
+
+ /* disable i2c slave */
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0);
+ if (ret)
+ goto error_disable_i2c;
+
+ /* check i2c status */
+ ret = regmap_read(st->map, INV_MPU6050_REG_I2C_MST_STATUS, &status);
+ if (ret)
+ return ret;
+ if (status & INV_MPU6050_BIT_I2C_SLV0_NACK)
+ return -EIO;
+
+ /* read data in registers */
+ return regmap_bulk_read(st->map, INV_MPU6050_REG_EXT_SENS_DATA,
+ val, size);
+
+error_disable_i2c:
+ regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0);
+ return ret;
+}
+
+/*
+ * i2c slave writing 1 byte using SLV0
+ */
+int inv_mpu_aux_write(const struct inv_mpu6050_state *st, uint8_t addr,
+ uint8_t reg, uint8_t val)
+{
+ unsigned int status;
+ int ret;
+
+ /* setup i2c SLV0 control: i2c addr, register, value, enable + size */
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(0), addr);
+ if (ret)
+ return ret;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(0), reg);
+ if (ret)
+ return ret;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_DO(0), val);
+ if (ret)
+ return ret;
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0),
+ INV_MPU6050_BIT_SLV_EN | 1);
+ if (ret)
+ return ret;
+
+ /* do i2c xfer */
+ ret = inv_mpu_i2c_master_xfer(st);
+ if (ret)
+ goto error_disable_i2c;
+
+ /* disable i2c slave */
+ ret = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0);
+ if (ret)
+ goto error_disable_i2c;
+
+ /* check i2c status */
+ ret = regmap_read(st->map, INV_MPU6050_REG_I2C_MST_STATUS, &status);
+ if (ret)
+ return ret;
+ if (status & INV_MPU6050_BIT_I2C_SLV0_NACK)
+ return -EIO;
+
+ return 0;
+
+error_disable_i2c:
+ regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(0), 0);
+ return ret;
+}
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h
new file mode 100644
index 000000000000..bae4eab58e6c
--- /dev/null
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_aux.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2019 TDK-InvenSense, Inc.
+ */
+
+#ifndef INV_MPU_AUX_H_
+#define INV_MPU_AUX_H_
+
+#include <linux/kernel.h>
+
+#include "inv_mpu_iio.h"
+
+/**
+ * inv_mpu_aux_init() - init i2c auxiliary bus
+ * @st: driver internal state
+ *
+ * Returns 0 on success, a negative error code otherwise.
+ */
+int inv_mpu_aux_init(const struct inv_mpu6050_state *st);
+
+/**
+ * inv_mpu_aux_read() - read register function for i2c auxiliary bus
+ * @st: driver internal state.
+ * @addr: chip i2c Address
+ * @reg: chip register address
+ * @val: buffer for storing read bytes
+ * @size: number of bytes to read
+ *
+ * Returns 0 on success, a negative error code otherwise.
+ */
+int inv_mpu_aux_read(const struct inv_mpu6050_state *st, uint8_t addr,
+ uint8_t reg, uint8_t *val, size_t size);
+
+/**
+ * inv_mpu_aux_write() - write register function for i2c auxiliary bus
+ * @st: driver internal state.
+ * @addr: chip i2c Address
+ * @reg: chip register address
+ * @val: 1 byte value to write
+ *
+ * Returns 0 on success, a negative error code otherwise.
+ */
+int inv_mpu_aux_write(const struct inv_mpu6050_state *st, uint8_t addr,
+ uint8_t reg, uint8_t val);
+
+#endif /* INV_MPU_AUX_H_ */
--
2.17.1
