Document the LTC2983 temperature sensor devicetree bindings. Signed-off-by: Nuno Sá <nuno.sa@xxxxxxxxxx> --- .../bindings/iio/temperature/adi,ltc2983.yaml | 442 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 443 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml diff --git a/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file mode 100644 index 000000000000..2b468b3ed177 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml @@ -0,0 +1,442 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2983 Multi-sensor Temperature system + +maintainers: + - Nuno Sá <nuno.sa@xxxxxxxxxx> + +description: | + Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System + https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf + +properties: + compatible: + enum: + - adi,ltc2983 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + adi,temperature-celcius: + description: + If this property is present, the temperature is reported in Celsius. + type: boolean + maxItems: 1 + + adi,mux-delay-config: + description: + The LTC2983 performs 2 or 3 internal conversion cycles per temperature result. + Each conversion cycle is performed with different excitation and input multiplexer + configurations. Prior to each conversion, these excitation circuits and input + switch configurations are changed and an internal 1ms delay ensures settling prior + to the conversion cycle in most cases. An extra delay can be configured using this + property. The value written here is multiplied by 100us. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - maximum: 255 + maxItems: 1 + + adi,filter-notch-freq: + description: + Set's the default setting of the digital filter. The default is simultaneous + 50/60Hz rejection. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1, 2] + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^thermocouple@([1-9]|1[0-9]|20)$": + type: object + description: Represents a thermocouple sensor which is connected to one of the device channels. + + properties: + reg: + description: | + The channel number. It can be connected to one of the 20 channels of the device. + Note that, for differential thermocouples, the minimum is 2. + minimum: 1 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the type of thermocouple connected to the device. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [1 2 3 4 5 6 7 8] + maxItems: 1 + + adi,sensor-config: + description: | + Raw value which set's the sensor configuration. Look at table 14 of the + datasheet for how to set this value for thermocouples. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 1 + - maximun: 15 + maxItems: 1 + + adi,cold-junction-handle: + description: | + Phandle which points to a sensor object responsible for measuring the + thermocouple cold junction temperature. + $ref: "/schemas/types.yaml#/definitions/phandle" + maxItems: 1 + + adi,custom-sensor: + description: | + This is a table, where each entry should be a pair of voltage(mv)-temperature(K). + The entries must be given in nv and uK so that, the original values must be + multiplied by 1000000. For more details look at table 69 and 70. + allOf: + - $ref: /schemas/types.yaml#/definitions/int64-array + minItems: 6 + maxItems: 128 + required: + - reg + - adi,sensor-type + +patternProperties: + "^diode@([1-9]|1[0-9]|20)$": + type: object + description: Represents a diode sensor which is connected to one of the device channels. + + properties: + reg: + description: + The channel number. It can be connected to one of the 20 channels of the device. + Note that, for differential diodes, the minimum is 2. + minimum: 1 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the sensor as a diode. + const: 28 + maxItems: 1 + + adi,sensor-config: + description: | + Raw value which set's the sensor configuration. Look at table 17 of the + datasheet for how to set this value for diodes. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0 1 2 3 4 5 6 7] + maxItems: 1 + + adi,excitation-current: + description: | + This property controls the magnitude of the excitation current applied + to the diode. Look at table 19 of the datasheet for more info. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0 1 2 3] + maxItems: 1 + + adi,ideal-factor-value: + description: | + This property sets the diode ideality factor. The real value must be + multiplied by 1000000 to remove the fractional part. For more information + look at table 20 of the datasheet. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + + required: + - reg + - adi,sensor-type + +patternProperties: + "^rtd@([2-9]|1[0-9]|20)$": + type: object + description: Represents a rtd sensor which is connected to one of the device channels. + + properties: + reg: + description: | + The channel number. It can be connected to one of the 20 channels of the device. + minimum: 2 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the type of RTD connected to the device. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [10 11 12 13 14 15 16 17] + maxItems: 1 + + adi,rsense-handle: + description: | + Phandle pointing to a rsense object associated with this RTD. + $ref: "/schemas/types.yaml#/definitions/phandle" + maxItems: 1 + + adi,sensor-config: + description: | + Raw value which set's the sensor configuration. Look at table 28 of the + datasheet for how to set this value for RTD's. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0 1 4 5 8 9 10 12 13 14] + maxItems: 1 + + adi,excitation-current: + description: | + This property controls the magnitude of the excitation current applied + to the RTD. Look at table 29 of the datasheet for more info. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [1 2 3 4 5 6 7 8] + maxItems: 1 + + adi,rtd-curve: + description: | + This property set the RTD curve used and the corresponding Callendar-Van + Dusen constants. Look at table 30 of the datasheet. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0 1 2 3] + maxItems: 1 + + adi,custom-sensor: + description: | + This is a table, where each entry should be a pair of resistance(ohm)-temperature(K). + The entries added here are in uohm and uK. For more details values look at table 74 and 75. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-array + minItems: 6 + maxItems: 128 + required: + - reg + - adi,sensor-type + - adi,rsense-handle + +patternProperties: + "^thermistor@([1-9]|1[0-9]|20)$": + type: object + description: Represents a thermistor sensor which is connected to one of the device channels. + + properties: + reg: + description: | + The channel number. It can be connected to one of the 20 channels of the device. + Note that, for differential thermistors, the minimum is 2. + minimum: 1 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the type of thermistor connected to the device. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [19 20 21 22 23 24 25] + maxItems: 1 + + adi,rsense-handle: + description: | + Phandle pointing to a rsense object associated with this thermistor. + $ref: "/schemas/types.yaml#/definitions/phandle" + maxItems: 1 + + adi,sensor-config: + description: | + Raw value which set's the sensor configuration. Look at table 52 of the + datasheet for how to set this value for thermistors. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0 1 2 4] + maxItems: 1 + + adi,excitation-current: + description: | + This property controls the magnitude of the excitation current applied + to the thermistor. Look at table 53 of the datasheet for more info. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - enum: [1 2 3 4 5 6 7 8 9 10 11 12] + maxItems: 1 + + adi,custom-sensor: + description: | + This is a table, where each entry should be a pair of resistance(ohm)-temperature(K). + The entries added here are in uohm and uK only for custom thermistors. + For more details look at table 78 and 79. + Steinhart-Hart coefficients are also supported and can be programmed into the + device memory using this property. For Steinhart sensors, this table has a constant + size of 6 entries (defining the coefficients) and the values are given in the raw format. + Look at table 82 for more information. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-array + minItems: 6 + maxItems: 128 + required: + - reg + - adi,sensor-type + - adi,rsense-handle + +patternProperties: + "^adc@([1-9]|1[0-9]|20)$": + type: object + description: Represents a channel which is being used as a direct adc. + + properties: + reg: + description: | + The channel number. It can be connected to one of the 20 channels of the device. + Note that, for differential adc's, the minimum is 2. + minimum: 1 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the sensor as a direct adc. + const: 30 + maxItems: 1 + + adi,single-ended: + description: | + Boolean property which set's the adc as single-ended. + type: boolean + + required: + - reg + - adi,sensor-type + +patternProperties: + "^rsense@([2-9]|1[0-9]|20)$": + type: object + description: | + Represents a rsense which is connected to one of the device channels. + Rsense are used by thermistors and RTD's. + + properties: + reg: + description: | + The channel number. It can be connected to one of the 20 channels of the device. + minimum: 2 + maximum: 20 + maxItems: 1 + + adi,sensor-type: + description: | + Identifies the sensor as a rsense. + const: 29 + maxItems: 1 + + adi,rsense-val-micro-ohms: + description: | + Sets the value of the sense resistor. Look at table 20 of the datasheet + for information. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64 + maxItems: 1 + + required: + - reg + - adi,sensor-type + - adi, rsense-val + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor_ltc2983: ltc2983@0 { + compatible = "adi,ltc2983"; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + adi,temperature-celcius; + interrupts = <20 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + + thermocouple@18 { + reg = <18>; + adi,sensor-type = <8>; //Type B + adi,sensor-config = <1>; //Differential, open-circuit current + adi,cold-junction-handle = <&diode5>; + }; + + diode5: diode@5 { + reg = <5>; + adi,sensor-type = <28>; + }; + + rsense2: rsense@2 { + reg = <2>; + adi,sensor-type = <29>; + adi,rsense-val-micro-ohms = /bits/ 64 <1200000000>; //1.2Kohms + }; + + rtd@14 { + reg = <14>; + adi,sensor-type = <15>; //PT1000 + /*2-wire, internal gnd, no current rotation*/ + adi,sensor-config = <1>; + adi,excitation-current = <7>; //500uA + adi,rsense-handle = <&rsense2>; + }; + + adc@10 { + reg = <10>; + adi,sensor-type = <30>; + adi,single-ended; + }; + + thermistor@12 { + reg = <12>; + adi,sensor-type = <26>; //Steinhart + adi,rsense-handle = <&rsense2>; + adi,custom-sensor = /bits/ 64 <0x00F371EC 0x12345678 + 0x2C0F8733 0x10018C66 0xA0FEACCD + 0x90021D99>; //6 entries + }; + + thermocouple@20 { + reg = <20>; + adi,sensor-type = <9>; //custom thermocouple + adi,sensor-config = <8>; //single-ended + adi,custom-sensor = /bits/ 64 + <(-50220000) 0 + (-30200000) 99100000 + (-5300000) 135400000 + 0 273150000 + 40200000 361200000 + 55300000 522100000 + 88300000 720300000 + 132200000 811200000 + 188700000 922500000 + 460400000 1000000000>; //10 pairs + }; + + }; + }; +... diff --git a/MAINTAINERS b/MAINTAINERS index 14a256e785ca..f747a9dc27f5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9497,6 +9497,7 @@ W: http://ez.analog.com/community/linux-device-drivers L: linux-iio@xxxxxxxxxxxxxxx S: Supported F: drivers/iio/temperature/ltc2983.c +F: Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml LTC4261 HARDWARE MONITOR DRIVER M: Guenter Roeck <linux@xxxxxxxxxxxx> -- 2.23.0
