On Thu, 22 Aug 2019 16:52:31 +0200 Linus Walleij <linus.walleij@xxxxxxxxxx> wrote: > This is a new driver for the ST-Ericsson AB8500 GPADC, which > replaces the old driver in drivers/mfd/ab8500-gpadc.c and > thus gets rid of another necessarily different custom driver > from the times before IIO existed. > > The AB8500 GPADC can convert 10 different channels and these > are used for monitoring voltages in the U8500 chipset, some > are used for battery charging, some for temperature > monitoring. > > As this is very core functionality that a lot of drivers > depend on and was formerly compiled in with the AB8500 core > driver, we deafault it to 'y' in Kconfig: it can be compiled > out but it is really not advisible: the platform can > for example overheat if we do. > > Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx> Good to see this come back ;) I'll confess I've completely forgotten it so will just do a fresh review as if it were a v1. Note we have standardized the specification of ADC channels since v1. See Documentation/devicetree/bindings/iio/adc/adc.txt It's fairly similar to what you have though so easy tweak to bindings. I don't think any change in here is needed. Some minor stuff inline otherwise. Fix those up and you can add Reviewed-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> What is your merge plan for these? Thanks, Jonathan > --- > ChangeLog v1 -> v2: > - Break out the IIO driver into a separate patch just adding > it instead of moving it in the same patch, this makes it > easier for the IIO maintainers to review the patch. > - Rename a slew of variables and fix up comment syntax etc. > - Drop the enums for sample numbers 1, 4, 8, 16 just use numerals. > - Use a bool to indicate trigger on falling edge rather than a number. > - Use a bool to indicate hardware conversion on a channel. > - Use an enum for the channels. > - Pass a pointer to the channel config struct instead of overly > talkative function prototype. > - Use devm_iio_device_register() > - Push the channels into the IIO device, do not keep a separate > copy of the IIO channels inside the driver state container. > - Do not mark interrupts as shared. They are not shared. > - Remove comments commenting the obvious. > - Add prefixed to definitions and enums to avoid clashes with > other namespaces and make it obvious where things are coming > from. > - Drop surplus local variable. > - Drop unused OTP retrieveal function for AB8540. > - Use runtime PM for system PM callbacks. > - Use builtin_platform_driver() for initializing the driver as > this is a bool menuconfig. > - Fix up processed reads from the ADC: I mistakedly dropped the > flag indicating we can do processed reads, falling us back to > just raw reads. > --- > MAINTAINERS | 1 + > drivers/iio/adc/Kconfig | 10 + > drivers/iio/adc/Makefile | 1 + > drivers/iio/adc/ab8500-gpadc.c | 1240 ++++++++++++++++++++++++++++++++ > 4 files changed, 1252 insertions(+) > create mode 100644 drivers/iio/adc/ab8500-gpadc.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 43604d6ab96c..a2fee2f03530 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1978,6 +1978,7 @@ F: drivers/dma/ste_dma40* > F: drivers/hwspinlock/u8500_hsem.c > F: drivers/i2c/busses/i2c-nomadik.c > F: drivers/i2c/busses/i2c-stu300.c > +F: drivers/iio/adc/ab8500-gpadc.c > F: drivers/mfd/ab3100* > F: drivers/mfd/ab8500* > F: drivers/mfd/abx500* > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig > index 7e3286265a38..fba7ddcdd8e2 100644 > --- a/drivers/iio/adc/Kconfig > +++ b/drivers/iio/adc/Kconfig > @@ -6,6 +6,16 @@ > > menu "Analog to digital converters" > > +config AB8500_GPADC > + bool "ST-Ericsson AB8500 GPADC driver" > + depends on AB8500_CORE && REGULATOR_AB8500 > + default y > + help > + AB8500 Analog Baseband, mixed signal integrated circuit GPADC > + (General Purpose Analog to Digital Converter) driver used to monitor > + internal voltages, convert accessory and battery, AC (charger, mains) > + and USB voltages integral to the U8500 platform. > + > config AD_SIGMA_DELTA > tristate > select IIO_BUFFER > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile > index ef9cc485fb67..fc1b6ebb0cde 100644 > --- a/drivers/iio/adc/Makefile > +++ b/drivers/iio/adc/Makefile > @@ -4,6 +4,7 @@ > # > > # When adding new entries keep the list in alphabetical order > +obj-$(CONFIG_AB8500_GPADC) += ab8500-gpadc.o > obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o > obj-$(CONFIG_AD7124) += ad7124.o > obj-$(CONFIG_AD7266) += ad7266.o > diff --git a/drivers/iio/adc/ab8500-gpadc.c b/drivers/iio/adc/ab8500-gpadc.c > new file mode 100644 > index 000000000000..e8abaf002c1c > --- /dev/null > +++ b/drivers/iio/adc/ab8500-gpadc.c > @@ -0,0 +1,1240 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (C) ST-Ericsson SA 2010 > + * > + * Author: Arun R Murthy <arun.murthy@xxxxxxxxxxxxxx> > + * Author: Daniel Willerud <daniel.willerud@xxxxxxxxxxxxxx> > + * Author: Johan Palsson <johan.palsson@xxxxxxxxxxxxxx> > + * Author: M'boumba Cedric Madianga > + * Author: Linus Walleij <linus.walleij@xxxxxxxxxx> > + * > + * AB8500 General Purpose ADC driver. The AB8500 uses reference voltages: > + * VinVADC, and VADC relative to GND to do its job. It monitors main and backup > + * battery voltages, AC (mains) voltage, USB cable voltage, as well as voltages > + * representing the temperature of the chip die and battery, accessory > + * detection by resistance measurements using relative voltages and GSM burst > + * information. > + * > + * Some of the voltages are measured on external pins on the IC, such as > + * battery temperature or "ADC aux" 1 and 2. Other voltages are internal rails > + * from other parts of the ASIC such as main charger voltage, main and battery > + * backup voltage or USB VBUS voltage. For this reason drivers for other > + * parts of the system are required to obtain handles to the ADC to do work > + * for them and the IIO driver provides arbitration among these consumers. > + */ > +#include <linux/init.h> > +#include <linux/bits.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > +#include <linux/device.h> > +#include <linux/interrupt.h> > +#include <linux/spinlock.h> > +#include <linux/delay.h> > +#include <linux/pm_runtime.h> > +#include <linux/platform_device.h> > +#include <linux/completion.h> > +#include <linux/regulator/consumer.h> > +#include <linux/random.h> > +#include <linux/err.h> > +#include <linux/slab.h> > +#include <linux/mfd/abx500.h> > +#include <linux/mfd/abx500/ab8500.h> > + > +/* GPADC register offsets and bit definitions */ > + > +#define AB8500_GPADC_CTRL1_REG 0x00 > +/* GPADC control register 1 bits */ > +#define AB8500_GPADC_CTRL1_DISABLE 0x00 > +#define AB8500_GPADC_CTRL1_ENABLE BIT(0) > +#define AB8500_GPADC_CTRL1_TRIG_ENA BIT(1) > +#define AB8500_GPADC_CTRL1_START_SW_CONV BIT(2) > +#define AB8500_GPADC_CTRL1_BTEMP_PULL_UP BIT(3) > +/* 0 = use rising edge, 1 = use falling edge */ > +#define AB8500_GPADC_CTRL1_TRIG_EDGE BIT(4) > +/* 0 = use VTVOUT, 1 = use VRTC as pull-up supply for battery temp NTC */ > +#define AB8500_GPADC_CTRL1_PUPSUPSEL BIT(5) > +#define AB8500_GPADC_CTRL1_BUF_ENA BIT(6) > +#define AB8500_GPADC_CTRL1_ICHAR_ENA BIT(7) > + > +#define AB8500_GPADC_CTRL2_REG 0x01 > +#define AB8500_GPADC_CTRL3_REG 0x02 > +/* > + * GPADC control register 2 and 3 bits > + * the bit layout is the same for SW and HW conversion set-up > + */ > +#define AB8500_GPADC_CTRL2_AVG_1 0x00 > +#define AB8500_GPADC_CTRL2_AVG_4 BIT(5) > +#define AB8500_GPADC_CTRL2_AVG_8 BIT(6) > +#define AB8500_GPADC_CTRL2_AVG_16 (BIT(5) | BIT(6)) > + > +enum ab8500_gpadc_channel { > + AB8500_GPADC_CHAN_UNUSED = 0x00, > + AB8500_GPADC_CHAN_BAT_CTRL = 0x01, > + AB8500_GPADC_CHAN_BAT_TEMP = 0x02, > + /* This is not used on AB8505 */ > + AB8500_GPADC_CHAN_MAIN_CHARGER = 0x03, > + AB8500_GPADC_CHAN_ACC_DET_1 = 0x04, > + AB8500_GPADC_CHAN_ACC_DET_2 = 0x05, > + AB8500_GPADC_CHAN_ADC_AUX_1 = 0x06, > + AB8500_GPADC_CHAN_ADC_AUX_2 = 0x07, > + AB8500_GPADC_CHAN_VBAT_A = 0x08, > + AB8500_GPADC_CHAN_VBUS = 0x09, > + AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT = 0x0a, > + AB8500_GPADC_CHAN_USB_CHARGER_CURRENT = 0x0b, > + AB8500_GPADC_CHAN_BACKUP_BAT = 0x0c, > + /* Only on AB8505 */ > + AB8505_GPADC_CHAN_DIE_TEMP = 0x0d, > + AB8500_GPADC_CHAN_ID = 0x0e, > + AB8500_GPADC_CHAN_INTERNAL_TEST_1 = 0x0f, > + AB8500_GPADC_CHAN_INTERNAL_TEST_2 = 0x10, > + AB8500_GPADC_CHAN_INTERNAL_TEST_3 = 0x11, > + /* FIXME: Applicable to all ASIC variants? */ > + AB8500_GPADC_CHAN_XTAL_TEMP = 0x12, > + AB8500_GPADC_CHAN_VBAT_TRUE_MEAS = 0x13, > + /* FIXME: Doesn't seem to work with pure AB8500 */ > + AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT = 0x1c, > + AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT = 0x1d, > + AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT = 0x1e, > + AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT = 0x1f, > + /* > + * Virtual channel used only for ibat conversion to ampere. > + * Battery current conversion (ibat) cannot be requested as a > + * single conversion but it is always requested in combination > + * with other input requests. > + */ > + AB8500_GPADC_CHAN_IBAT_VIRTUAL = 0xFF, > +}; > + > +#define AB8500_GPADC_AUTO_TIMER_REG 0x03 > + > +#define AB8500_GPADC_STAT_REG 0x04 > +#define AB8500_GPADC_STAT_BUSY BIT(0) > + > +#define AB8500_GPADC_MANDATAL_REG 0x05 > +#define AB8500_GPADC_MANDATAH_REG 0x06 > +#define AB8500_GPADC_AUTODATAL_REG 0x07 > +#define AB8500_GPADC_AUTODATAH_REG 0x08 > +#define AB8500_GPADC_MUX_CTRL_REG 0x09 > +#define AB8540_GPADC_MANDATA2L_REG 0x09 > +#define AB8540_GPADC_MANDATA2H_REG 0x0A > +#define AB8540_GPADC_APEAAX_REG 0x10 > +#define AB8540_GPADC_APEAAT_REG 0x11 > +#define AB8540_GPADC_APEAAM_REG 0x12 > +#define AB8540_GPADC_APEAAH_REG 0x13 > +#define AB8540_GPADC_APEAAL_REG 0x14 > + > +/* > + * OTP register offsets > + * Bank : 0x15 > + */ > +#define AB8500_GPADC_CAL_1 0x0F > +#define AB8500_GPADC_CAL_2 0x10 > +#define AB8500_GPADC_CAL_3 0x11 > +#define AB8500_GPADC_CAL_4 0x12 > +#define AB8500_GPADC_CAL_5 0x13 > +#define AB8500_GPADC_CAL_6 0x14 > +#define AB8500_GPADC_CAL_7 0x15 > +/* New calibration for 8540 */ > +#define AB8540_GPADC_OTP4_REG_7 0x38 > +#define AB8540_GPADC_OTP4_REG_6 0x39 > +#define AB8540_GPADC_OTP4_REG_5 0x3A > + > +#define DIS_ZERO 0x00 > +#define EN_VBIAS_XTAL_TEMP 0x02 > + > +/* GPADC constants from AB8500 spec, UM0836 */ > +#define ADC_RESOLUTION 1024 Prefix? > +#define ADC_CH_BTEMP_MIN 0 > +#define ADC_CH_BTEMP_MAX 1350 > +#define ADC_CH_DIETEMP_MIN 0 > +#define ADC_CH_DIETEMP_MAX 1350 > +#define ADC_CH_CHG_V_MIN 0 > +#define ADC_CH_CHG_V_MAX 20030 > +#define ADC_CH_ACCDET2_MIN 0 > +#define ADC_CH_ACCDET2_MAX 2500 > +#define ADC_CH_VBAT_MIN 2300 > +#define ADC_CH_VBAT_MAX 4800 > +#define ADC_CH_CHG_I_MIN 0 > +#define ADC_CH_CHG_I_MAX 1500 > +#define ADC_CH_BKBAT_MIN 0 > +#define ADC_CH_BKBAT_MAX 3200 > + > +/* GPADC constants from AB8540 spec */ > +#define ADC_CH_IBAT_MIN (-6000) /* mA range measured by ADC for ibat */ > +#define ADC_CH_IBAT_MAX 6000 > +#define ADC_CH_IBAT_MIN_V (-60) /* mV range measured by ADC for ibat */ > +#define ADC_CH_IBAT_MAX_V 60 > +#define IBAT_VDROP_L (-56) /* mV */ > +#define IBAT_VDROP_H 56 > + > +/* This is used to not lose precision when dividing to get gain and offset */ > +#define CALIB_SCALE 1000 > +/* > + * Number of bits shift used to not lose precision > + * when dividing to get ibat gain. > + */ > +#define CALIB_SHIFT_IBAT 20 > + > +/* Time in ms before disabling regulator */ > +#define GPADC_AUDOSUSPEND_DELAY 1 > + > +#define CONVERSION_TIME 500 /* ms */ > + > +enum ab8500_cal_channels { > + AB8500_CAL_VMAIN = 0, > + AB8500_CAL_BTEMP, > + AB8500_CAL_VBAT, > + AB8500_CAL_IBAT, > + AB8500_CAL_NR, > +}; > + > +/** > + * struct ab8500_adc_cal_data - Table for storing gain and offset for the > + * calibrated ADC channels > + * @gain: Gain of the ADC channel > + * @offset: Offset of the ADC channel > + * @otp_calib_hi: Calibration from OTP > + * @otp_calib_lo: Calibration from OTP > + */ > +struct ab8500_adc_cal_data { > + s64 gain; > + s64 offset; > + u16 otp_calib_hi; > + u16 otp_calib_lo; > +}; > + > +/** > + * struct ab8500_gpadc_chan_info - per-channel GPADC info > + * @name: name of the channel > + * @id: the internal AB8500 ID number for the channel > + * @hardware_control: indicate that we want to use hardware ADC control > + * on this channel, the default is software ADC control. Hardware control > + * is normally only used to test the battery voltage during GSM bursts > + * and needs a hardware trigger on the GPADCTrig pin of the ASIC. > + * @falling_edge: indicate that we want to trigger on falling edge > + * rather than rising edge, rising edge is the default > + * @avg_sample: how many samples to average: must be 1, 4, 8 or 16. > + * @trig_timer: how long to wait for the trigger, in 32kHz periods: > + * 0 .. 255 periods > + */ > +struct ab8500_gpadc_chan_info { > + const char *name; > + u8 id; > + bool hardware_control; > + bool falling_edge; > + u8 avg_sample; > + u8 trig_timer; > +}; > + > +/** > + * struct ab8500_gpadc - AB8500 GPADC device information > + * @dev: pointer to the containing device > + * @ab8500: pointer to the parent AB8500 device > + * @chans: internal per-channel information container > + * @nchans: number of channels > + * @complete: pointer to the completion that indicates > + * the completion of an gpadc conversion cycle > + * @vddadc: pointer to the regulator supplying VDDADC > + * @irq_sw: interrupt number that is used by gpadc for software ADC conversion > + * @irq_hw: interrupt number that is used by gpadc for hardware ADC conversion > + * @cal_data: array of ADC calibration data structs > + */ > +struct ab8500_gpadc { > + struct device *dev; > + struct ab8500 *ab8500; > + struct ab8500_gpadc_chan_info *chans; > + unsigned int nchans; > + struct completion complete; > + struct regulator *vddadc; > + int irq_sw; > + int irq_hw; > + struct ab8500_adc_cal_data cal_data[AB8500_CAL_NR]; > +}; > + > +static struct ab8500_gpadc_chan_info * > +ab8500_gpadc_get_channel(struct ab8500_gpadc *gpadc, u8 chan) > +{ > + struct ab8500_gpadc_chan_info *ch; > + int i; > + > + for (i = 0; i < gpadc->nchans; i++) { > + ch = &gpadc->chans[i]; > + if (ch->id == chan) > + break; > + } > + if (i == gpadc->nchans) > + return NULL; > + > + return ch; > +} > + > +/** > + * ab8500_gpadc_ad_to_voltage() - Convert a raw ADC value to a voltage Kernel doc should be complete if you are going to do it... > + */ > +static int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, > + enum ab8500_gpadc_channel ch, > + int ad_value) > +{ > + int res; > + > + switch (ch) { > + case AB8500_GPADC_CHAN_MAIN_CHARGER: > + /* No calibration data available: just interpolate */ > + if (!gpadc->cal_data[AB8500_CAL_VMAIN].gain) { > + res = ADC_CH_CHG_V_MIN + (ADC_CH_CHG_V_MAX - > + ADC_CH_CHG_V_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + } > + /* Here we can use calibration */ > + res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VMAIN].gain + > + gpadc->cal_data[AB8500_CAL_VMAIN].offset) / CALIB_SCALE; > + break; > + > + case AB8500_GPADC_CHAN_BAT_CTRL: > + case AB8500_GPADC_CHAN_BAT_TEMP: > + case AB8500_GPADC_CHAN_ACC_DET_1: > + case AB8500_GPADC_CHAN_ADC_AUX_1: > + case AB8500_GPADC_CHAN_ADC_AUX_2: > + case AB8500_GPADC_CHAN_XTAL_TEMP: > + /* No calibration data available: just interpolate */ > + if (!gpadc->cal_data[AB8500_CAL_BTEMP].gain) { > + res = ADC_CH_BTEMP_MIN + (ADC_CH_BTEMP_MAX - > + ADC_CH_BTEMP_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + } > + /* Here we can use calibration */ > + res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_BTEMP].gain + > + gpadc->cal_data[AB8500_CAL_BTEMP].offset) / CALIB_SCALE; > + break; > + > + case AB8500_GPADC_CHAN_VBAT_A: > + case AB8500_GPADC_CHAN_VBAT_TRUE_MEAS: > + /* No calibration data available: just interpolate */ > + if (!gpadc->cal_data[AB8500_CAL_VBAT].gain) { > + res = ADC_CH_VBAT_MIN + (ADC_CH_VBAT_MAX - > + ADC_CH_VBAT_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + } > + /* Here we can use calibration */ > + res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VBAT].gain + > + gpadc->cal_data[AB8500_CAL_VBAT].offset) / CALIB_SCALE; > + break; > + > + case AB8505_GPADC_CHAN_DIE_TEMP: > + res = ADC_CH_DIETEMP_MIN + > + (ADC_CH_DIETEMP_MAX - ADC_CH_DIETEMP_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + > + case AB8500_GPADC_CHAN_ACC_DET_2: > + res = ADC_CH_ACCDET2_MIN + > + (ADC_CH_ACCDET2_MAX - ADC_CH_ACCDET2_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + > + case AB8500_GPADC_CHAN_VBUS: > + res = ADC_CH_CHG_V_MIN + > + (ADC_CH_CHG_V_MAX - ADC_CH_CHG_V_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + > + case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT: > + case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT: > + res = ADC_CH_CHG_I_MIN + > + (ADC_CH_CHG_I_MAX - ADC_CH_CHG_I_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + > + case AB8500_GPADC_CHAN_BACKUP_BAT: > + res = ADC_CH_BKBAT_MIN + > + (ADC_CH_BKBAT_MAX - ADC_CH_BKBAT_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + > + case AB8500_GPADC_CHAN_IBAT_VIRTUAL: > + /* No calibration data available: just interpolate */ > + if (!gpadc->cal_data[AB8500_CAL_IBAT].gain) { > + res = ADC_CH_IBAT_MIN + (ADC_CH_IBAT_MAX - > + ADC_CH_IBAT_MIN) * ad_value / > + ADC_RESOLUTION; > + break; > + } > + /* Here we can use calibration */ > + res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_IBAT].gain + > + gpadc->cal_data[AB8500_CAL_IBAT].offset) > + >> CALIB_SHIFT_IBAT; > + break; > + > + default: > + dev_err(gpadc->dev, > + "unknown channel ID: %d, not possible to convert\n", > + ch); > + res = -EINVAL; > + break; > + > + } > + > + return res; > +} > + > +static int ab8500_gpadc_read(struct ab8500_gpadc *gpadc, > + const struct ab8500_gpadc_chan_info *ch, > + int *ibat) > +{ > + int ret; > + int looplimit = 0; > + unsigned long completion_timeout; > + u8 val; > + u8 low_data, high_data, low_data2, high_data2; > + u8 ctrl1; > + u8 ctrl23; > + unsigned int delay_min = 0; > + unsigned int delay_max = 0; > + u8 data_low_addr, data_high_addr; > + > + if (!gpadc) > + return -ENODEV; > + > + /* check if conversion is supported */ > + if ((gpadc->irq_sw <= 0) && !ch->hardware_control) > + return -ENOTSUPP; > + if ((gpadc->irq_hw <= 0) && ch->hardware_control) > + return -ENOTSUPP; > + > + /* Enable vddadc by grabbing PM runtime */ > + pm_runtime_get_sync(gpadc->dev); > + > + /* Check if ADC is not busy, lock and proceed */ > + do { > + ret = abx500_get_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_STAT_REG, &val); > + if (ret < 0) > + goto out; > + if (!(val & AB8500_GPADC_STAT_BUSY)) > + break; > + msleep(20); > + } while (++looplimit < 10); > + if (looplimit >= 10 && (val & AB8500_GPADC_STAT_BUSY)) { > + dev_err(gpadc->dev, "gpadc_conversion: GPADC busy"); > + ret = -EINVAL; > + goto out; > + } > + > + /* Enable GPADC */ > + ctrl1 = AB8500_GPADC_CTRL1_ENABLE; > + > + /* Select the channel source and set average samples */ > + switch (ch->avg_sample) { > + case 1: > + ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_1; > + break; > + case 4: > + ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_4; > + break; > + case 8: > + ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_8; > + break; > + default: > + ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_16; > + break; > + } > + > + if (ch->hardware_control) { > + ret = abx500_set_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_CTRL3_REG, ctrl23); > + ctrl1 |= AB8500_GPADC_CTRL1_TRIG_ENA; > + if (ch->falling_edge) > + ctrl1 |= AB8500_GPADC_CTRL1_TRIG_EDGE; > + } else { > + ret = abx500_set_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_CTRL2_REG, ctrl23); > + } > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: set avg samples failed\n"); > + goto out; > + } > + > + /* > + * Enable ADC, buffering, select rising edge and enable ADC path > + * charging current sense if it needed, ABB 3.0 needs some special > + * treatment too. > + */ > + switch (ch->id) { > + case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT: > + case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT: > + ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA | > + AB8500_GPADC_CTRL1_ICHAR_ENA; > + break; > + case AB8500_GPADC_CHAN_BAT_TEMP: > + if (!is_ab8500_2p0_or_earlier(gpadc->ab8500)) { > + ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA | > + AB8500_GPADC_CTRL1_BTEMP_PULL_UP; > + /* > + * Delay might be needed for ABB8500 cut 3.0, if not, > + * remove when hardware will be available > + */ > + delay_min = 1000; /* Delay in micro seconds */ > + delay_max = 10000; /* large range optimises sleepmode */ > + break; > + } > + /* Fall through */ > + default: > + ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA; > + break; > + } > + > + /* Write configuration to control register 1 */ > + ret = abx500_set_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ctrl1); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: set Control register failed\n"); > + goto out; > + } > + > + if (delay_min != 0) > + usleep_range(delay_min, delay_max); > + > + if (ch->hardware_control) { > + /* Set trigger delay timer */ > + ret = abx500_set_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_AUTO_TIMER_REG, > + ch->trig_timer); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: trig timer failed\n"); > + goto out; > + } > + completion_timeout = 2 * HZ; > + data_low_addr = AB8500_GPADC_AUTODATAL_REG; > + data_high_addr = AB8500_GPADC_AUTODATAH_REG; > + } else { > + /* Start SW conversion */ > + ret = abx500_mask_and_set_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8500_GPADC_CTRL1_REG, > + AB8500_GPADC_CTRL1_START_SW_CONV, > + AB8500_GPADC_CTRL1_START_SW_CONV); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: start s/w conv failed\n"); > + goto out; > + } > + completion_timeout = msecs_to_jiffies(CONVERSION_TIME); > + data_low_addr = AB8500_GPADC_MANDATAL_REG; > + data_high_addr = AB8500_GPADC_MANDATAH_REG; > + } > + > + /* Wait for completion of conversion */ > + if (!wait_for_completion_timeout(&gpadc->complete, > + completion_timeout)) { > + dev_err(gpadc->dev, > + "timeout didn't receive GPADC conv interrupt\n"); > + ret = -EINVAL; > + goto out; > + } > + > + /* Read the converted RAW data */ > + ret = abx500_get_register_interruptible(gpadc->dev, > + AB8500_GPADC, data_low_addr, &low_data); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: read low data failed\n"); > + goto out; > + } > + > + ret = abx500_get_register_interruptible(gpadc->dev, > + AB8500_GPADC, data_high_addr, &high_data); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: read high data failed\n"); > + goto out; > + } > + > + /* Check if double conversion is required */ > + if ((ch->id == AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT) || > + (ch->id == AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT) || > + (ch->id == AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT) || > + (ch->id == AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT)) { > + > + if (ch->hardware_control) { > + /* not supported */ > + ret = -ENOTSUPP; > + dev_err(gpadc->dev, > + "gpadc_conversion: only SW double conversion supported\n"); > + goto out; > + } else { > + /* Read the converted RAW data 2 */ > + ret = abx500_get_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8540_GPADC_MANDATA2L_REG, > + &low_data2); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: read sw low data 2 failed\n"); > + goto out; > + } > + > + ret = abx500_get_register_interruptible(gpadc->dev, > + AB8500_GPADC, AB8540_GPADC_MANDATA2H_REG, > + &high_data2); > + if (ret < 0) { > + dev_err(gpadc->dev, > + "gpadc_conversion: read sw high data 2 failed\n"); > + goto out; > + } > + if (ibat != NULL) { > + *ibat = (high_data2 << 8) | low_data2; > + } else { > + dev_warn(gpadc->dev, > + "gpadc_conversion: ibat not stored\n"); > + } > + > + } > + } > + > + /* Disable GPADC */ > + ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC, > + AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE); > + if (ret < 0) { > + dev_err(gpadc->dev, "gpadc_conversion: disable gpadc failed\n"); > + goto out; > + } > + > + /* This eventually drops the regulator */ > + pm_runtime_mark_last_busy(gpadc->dev); > + pm_runtime_put_autosuspend(gpadc->dev); > + > + return (high_data << 8) | low_data; > + > +out: > + /* > + * It has shown to be needed to turn off the GPADC if an error occurs, > + * otherwise we might have problem when waiting for the busy bit in the > + * GPADC status register to go low. In V1.1 there wait_for_completion > + * seems to timeout when waiting for an interrupt.. Not seen in V2.0 > + */ > + (void) abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC, > + AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE); > + pm_runtime_put(gpadc->dev); > + dev_err(gpadc->dev, > + "gpadc_conversion: Failed to AD convert channel %d\n", ch->id); > + > + return ret; > +} > + > +/** > + * ab8500_bm_gpadcconvend_handler() - isr for gpadc conversion completion > + * @irq: irq number > + * @data: pointer to the data passed during request irq > + * > + * This is a interrupt service routine for gpadc conversion completion. > + * Notifies the gpadc completion is completed and the converted raw value > + * can be read from the registers. > + * Returns IRQ status(IRQ_HANDLED) > + */ > +static irqreturn_t ab8500_bm_gpadcconvend_handler(int irq, void *data) > +{ > + struct ab8500_gpadc *gpadc = data; > + > + complete(&gpadc->complete); > + > + return IRQ_HANDLED; > +} > + > +static int otp_cal_regs[] = { > + AB8500_GPADC_CAL_1, > + AB8500_GPADC_CAL_2, > + AB8500_GPADC_CAL_3, > + AB8500_GPADC_CAL_4, > + AB8500_GPADC_CAL_5, > + AB8500_GPADC_CAL_6, > + AB8500_GPADC_CAL_7, > +}; > + > +static int otp4_cal_regs[] = { > + AB8540_GPADC_OTP4_REG_7, > + AB8540_GPADC_OTP4_REG_6, > + AB8540_GPADC_OTP4_REG_5, > +}; > + > +static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc) > +{ > + int i; > + int ret[ARRAY_SIZE(otp_cal_regs)]; > + u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)]; > + int ret_otp4[ARRAY_SIZE(otp4_cal_regs)]; > + u8 gpadc_otp4[ARRAY_SIZE(otp4_cal_regs)]; > + int vmain_high, vmain_low; > + int btemp_high, btemp_low; > + int vbat_high, vbat_low; > + int ibat_high, ibat_low; > + s64 V_gain, V_offset, V2A_gain, V2A_offset; > + > + /* First we read all OTP registers and store the error code */ > + for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) { > + ret[i] = abx500_get_register_interruptible(gpadc->dev, > + AB8500_OTP_EMUL, otp_cal_regs[i], &gpadc_cal[i]); > + if (ret[i] < 0) { > + /* Continue anyway: maybe the other registers are OK */ > + dev_err(gpadc->dev, "%s: read otp reg 0x%02x failed\n", > + __func__, otp_cal_regs[i]); > + } else { > + /* Put this in the entropy pool as device-unique */ > + add_device_randomness(&ret[i], sizeof(ret[i])); > + } > + } > + > + /* > + * The ADC calibration data is stored in OTP registers. > + * The layout of the calibration data is outlined below and a more > + * detailed description can be found in UM0836 > + * > + * vm_h/l = vmain_high/low > + * bt_h/l = btemp_high/low > + * vb_h/l = vbat_high/low > + * > + * Data bits 8500/9540: > + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | | vm_h9 | vm_h8 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 | > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * > + * Data bits 8540: > + * OTP2 > + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vm_h9 | vm_h8 | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 | > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * > + * Data bits 8540: > + * OTP4 > + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | | ib_h9 | ib_h8 | ib_h7 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | ib_h6 | ib_h5 | ib_h4 | ib_h3 | ib_h2 | ib_h1 | ib_h0 | ib_l5 > + * |.......|.......|.......|.......|.......|.......|.......|....... > + * | ib_l4 | ib_l3 | ib_l2 | ib_l1 | ib_l0 | > + * > + * > + * Ideal output ADC codes corresponding to injected input voltages > + * during manufacturing is: > + * > + * vmain_high: Vin = 19500mV / ADC ideal code = 997 > + * vmain_low: Vin = 315mV / ADC ideal code = 16 > + * btemp_high: Vin = 1300mV / ADC ideal code = 985 > + * btemp_low: Vin = 21mV / ADC ideal code = 16 > + * vbat_high: Vin = 4700mV / ADC ideal code = 982 > + * vbat_low: Vin = 2380mV / ADC ideal code = 33 > + */ > + > + if (is_ab8540(gpadc->ab8500)) { > + /* Calculate gain and offset for VMAIN if all reads succeeded*/ > + if (!(ret[1] < 0 || ret[2] < 0)) { > + vmain_high = (((gpadc_cal[1] & 0xFF) << 2) | > + ((gpadc_cal[2] & 0xC0) >> 6)); > + vmain_low = ((gpadc_cal[2] & 0x3E) >> 1); > + > + gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi = > + (u16)vmain_high; > + gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo = > + (u16)vmain_low; > + > + gpadc->cal_data[AB8500_CAL_VMAIN].gain = CALIB_SCALE * > + (19500 - 315) / (vmain_high - vmain_low); > + gpadc->cal_data[AB8500_CAL_VMAIN].offset = CALIB_SCALE * > + 19500 - (CALIB_SCALE * (19500 - 315) / > + (vmain_high - vmain_low)) * vmain_high; > + } else { > + gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0; > + } > + > + /* Read IBAT calibration Data */ > + for (i = 0; i < ARRAY_SIZE(otp4_cal_regs); i++) { > + ret_otp4[i] = abx500_get_register_interruptible( > + gpadc->dev, AB8500_OTP_EMUL, > + otp4_cal_regs[i], &gpadc_otp4[i]); > + if (ret_otp4[i] < 0) > + dev_err(gpadc->dev, > + "%s: read otp4 reg 0x%02x failed\n", > + __func__, otp4_cal_regs[i]); > + } > + > + /* Calculate gain and offset for IBAT if all reads succeeded */ > + if (!(ret_otp4[0] < 0 || ret_otp4[1] < 0 || ret_otp4[2] < 0)) { > + ibat_high = (((gpadc_otp4[0] & 0x07) << 7) | > + ((gpadc_otp4[1] & 0xFE) >> 1)); > + ibat_low = (((gpadc_otp4[1] & 0x01) << 5) | > + ((gpadc_otp4[2] & 0xF8) >> 3)); > + > + gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_hi = > + (u16)ibat_high; > + gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_lo = > + (u16)ibat_low; > + > + V_gain = ((IBAT_VDROP_H - IBAT_VDROP_L) > + << CALIB_SHIFT_IBAT) / (ibat_high - ibat_low); > + > + V_offset = (IBAT_VDROP_H << CALIB_SHIFT_IBAT) - > + (((IBAT_VDROP_H - IBAT_VDROP_L) << > + CALIB_SHIFT_IBAT) / (ibat_high - ibat_low)) > + * ibat_high; > + /* > + * Result obtained is in mV (at a scale factor), > + * we need to calculate gain and offset to get mA > + */ > + V2A_gain = (ADC_CH_IBAT_MAX - ADC_CH_IBAT_MIN)/ > + (ADC_CH_IBAT_MAX_V - ADC_CH_IBAT_MIN_V); > + V2A_offset = ((ADC_CH_IBAT_MAX_V * ADC_CH_IBAT_MIN - > + ADC_CH_IBAT_MAX * ADC_CH_IBAT_MIN_V) > + << CALIB_SHIFT_IBAT) > + / (ADC_CH_IBAT_MAX_V - ADC_CH_IBAT_MIN_V); > + > + gpadc->cal_data[AB8500_CAL_IBAT].gain = > + V_gain * V2A_gain; > + gpadc->cal_data[AB8500_CAL_IBAT].offset = > + V_offset * V2A_gain + V2A_offset; > + } else { > + gpadc->cal_data[AB8500_CAL_IBAT].gain = 0; > + } > + > + dev_dbg(gpadc->dev, "IBAT gain %llu offset %llu\n", > + gpadc->cal_data[AB8500_CAL_IBAT].gain, > + gpadc->cal_data[AB8500_CAL_IBAT].offset); > + } else { > + /* Calculate gain and offset for VMAIN if all reads succeeded */ > + if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) { > + vmain_high = (((gpadc_cal[0] & 0x03) << 8) | > + ((gpadc_cal[1] & 0x3F) << 2) | > + ((gpadc_cal[2] & 0xC0) >> 6)); > + vmain_low = ((gpadc_cal[2] & 0x3E) >> 1); > + > + gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi = > + (u16)vmain_high; > + gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo = > + (u16)vmain_low; > + > + gpadc->cal_data[AB8500_CAL_VMAIN].gain = CALIB_SCALE * > + (19500 - 315) / (vmain_high - vmain_low); > + > + gpadc->cal_data[AB8500_CAL_VMAIN].offset = CALIB_SCALE * > + 19500 - (CALIB_SCALE * (19500 - 315) / > + (vmain_high - vmain_low)) * vmain_high; > + } else { > + gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0; > + } > + } > + > + /* Calculate gain and offset for BTEMP if all reads succeeded */ > + if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) { > + btemp_high = (((gpadc_cal[2] & 0x01) << 9) | > + (gpadc_cal[3] << 1) | ((gpadc_cal[4] & 0x80) >> 7)); > + btemp_low = ((gpadc_cal[4] & 0x7C) >> 2); > + > + gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_hi = (u16)btemp_high; > + gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_lo = (u16)btemp_low; > + > + gpadc->cal_data[AB8500_CAL_BTEMP].gain = > + CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low); > + gpadc->cal_data[AB8500_CAL_BTEMP].offset = CALIB_SCALE * 1300 - > + (CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low)) > + * btemp_high; > + } else { > + gpadc->cal_data[AB8500_CAL_BTEMP].gain = 0; > + } > + > + /* Calculate gain and offset for VBAT if all reads succeeded */ > + if (!(ret[4] < 0 || ret[5] < 0 || ret[6] < 0)) { > + vbat_high = (((gpadc_cal[4] & 0x03) << 8) | gpadc_cal[5]); > + vbat_low = ((gpadc_cal[6] & 0xFC) >> 2); > + > + gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_hi = (u16)vbat_high; > + gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_lo = (u16)vbat_low; > + > + gpadc->cal_data[AB8500_CAL_VBAT].gain = CALIB_SCALE * > + (4700 - 2380) / (vbat_high - vbat_low); > + gpadc->cal_data[AB8500_CAL_VBAT].offset = CALIB_SCALE * 4700 - > + (CALIB_SCALE * (4700 - 2380) / > + (vbat_high - vbat_low)) * vbat_high; > + } else { > + gpadc->cal_data[AB8500_CAL_VBAT].gain = 0; > + } > + > + dev_dbg(gpadc->dev, "VMAIN gain %llu offset %llu\n", > + gpadc->cal_data[AB8500_CAL_VMAIN].gain, > + gpadc->cal_data[AB8500_CAL_VMAIN].offset); > + > + dev_dbg(gpadc->dev, "BTEMP gain %llu offset %llu\n", > + gpadc->cal_data[AB8500_CAL_BTEMP].gain, > + gpadc->cal_data[AB8500_CAL_BTEMP].offset); > + > + dev_dbg(gpadc->dev, "VBAT gain %llu offset %llu\n", > + gpadc->cal_data[AB8500_CAL_VBAT].gain, > + gpadc->cal_data[AB8500_CAL_VBAT].offset); > +} > + > +static int ab8500_gpadc_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + struct ab8500_gpadc *gpadc = iio_priv(indio_dev); > + const struct ab8500_gpadc_chan_info *ch; > + int raw_val; > + int processed; > + > + ch = ab8500_gpadc_get_channel(gpadc, chan->address); > + if (!ch) { > + dev_err(gpadc->dev, "no such channel %lu\n", > + chan->address); > + return -EINVAL; > + } > + > + dev_dbg(gpadc->dev, "read channel %d\n", ch->id); I'd suggest dropping these left over bits of debug. Easy enough to get the same info via other means (ftrace etc) > + > + raw_val = ab8500_gpadc_read(gpadc, ch, NULL); > + if (raw_val < 0) > + return raw_val; > + > + if (mask == IIO_CHAN_INFO_RAW) { > + *val = raw_val; > + return IIO_VAL_INT; > + } > + > + if (mask == IIO_CHAN_INFO_PROCESSED) { > + processed = ab8500_gpadc_ad_to_voltage(gpadc, ch->id, raw_val); > + if (processed < 0) > + return processed; > + > + /* Return millivolt or milliamps or millicentigrades */ > + *val = processed * 1000; > + return IIO_VAL_INT; > + } > + > + return -EINVAL; > +} > + > +static int ab8500_gpadc_of_xlate(struct iio_dev *indio_dev, > + const struct of_phandle_args *iiospec) > +{ > + int i; > + > + for (i = 0; i < indio_dev->num_channels; i++) > + if (indio_dev->channels[i].channel == iiospec->args[0]) > + return i; > + > + return -EINVAL; > +} > + > +static const struct iio_info ab8500_gpadc_info = { > + .of_xlate = ab8500_gpadc_of_xlate, > + .read_raw = ab8500_gpadc_read_raw, > +}; > + > +#ifdef CONFIG_PM > +static int ab8500_gpadc_runtime_suspend(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct ab8500_gpadc *gpadc = iio_priv(indio_dev); > + > + regulator_disable(gpadc->vddadc); > + > + return 0; > +} > + > +static int ab8500_gpadc_runtime_resume(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct ab8500_gpadc *gpadc = iio_priv(indio_dev); > + int ret; > + > + ret = regulator_enable(gpadc->vddadc); > + if (ret) > + dev_err(dev, "Failed to enable vddadc: %d\n", ret); > + > + return ret; > +} > +#endif > + > +/** > + * ab8500_gpadc_parse_channel() - process devicetree channel configuration > + * @dev: pointer to containing device > + * @np: device tree node for the channel to configure > + * @ch: channel info to fill in > + * @iio_chan: IIO channel specification to fill in > + * > + * The devicetree will set up the channel for use with the specific device, > + * and define usage for things like AUX GPADC inputs more precisely. > + */ > +static int ab8500_gpadc_parse_channel(struct device *dev, > + struct device_node *np, > + struct ab8500_gpadc_chan_info *ch, > + struct iio_chan_spec *iio_chan) > +{ > + const char *name = np->name; > + u32 chan; > + int ret; > + > + ret = of_property_read_u32(np, "reg", &chan); > + if (ret) { > + dev_err(dev, "invalid channel number %s\n", name); > + return ret; > + } > + if (chan > AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT) { > + dev_err(dev, "%s channel number out of range %d\n", name, chan); > + return -EINVAL; > + } > + > + iio_chan->channel = chan; > + iio_chan->datasheet_name = name; > + iio_chan->indexed = 1; > + iio_chan->address = chan; > + iio_chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > + BIT(IIO_CHAN_INFO_PROCESSED); > + /* Most are voltages (also temperatures), some are currents */ > + if ((chan == AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT) || > + (chan == AB8500_GPADC_CHAN_USB_CHARGER_CURRENT)) > + iio_chan->type = IIO_CURRENT; > + else > + iio_chan->type = IIO_VOLTAGE; > + > + ch->id = chan; > + > + /* Sensible defaults */ > + ch->avg_sample = 16; > + ch->hardware_control = false; > + ch->falling_edge = false; > + ch->trig_timer = 0; > + > + return 0; > +} > + > +/** > + * ab8500_gpadc_parse_channels() - Parse the GPADC channels from DT > + * @gpadc: the GPADC to configure the channels for > + * @np: device tree node containing the channel configurations > + * @chans: the IIO channels we parsed > + * @nchans: the number of IIO channels we parsed > + */ > +static int ab8500_gpadc_parse_channels(struct ab8500_gpadc *gpadc, > + struct device_node *np, > + struct iio_chan_spec **chans_parsed, > + unsigned int *nchans_parsed) > +{ > + struct device_node *child; > + struct ab8500_gpadc_chan_info *ch; > + struct iio_chan_spec *iio_chans; > + unsigned int nchans; > + int i; > + > + nchans = of_get_available_child_count(np); > + if (!nchans) { > + dev_err(gpadc->dev, "no channel children\n"); > + return -ENODEV; > + } > + dev_info(gpadc->dev, "found %d ADC channels\n", nchans); > + > + iio_chans = devm_kcalloc(gpadc->dev, nchans, > + sizeof(*iio_chans), GFP_KERNEL); > + if (!iio_chans) > + return -ENOMEM; > + > + gpadc->chans = devm_kcalloc(gpadc->dev, nchans, > + sizeof(*gpadc->chans), GFP_KERNEL); > + if (!gpadc->chans) > + return -ENOMEM; > + > + i = 0; > + for_each_available_child_of_node(np, child) { > + struct iio_chan_spec *iio_chan; > + int ret; > + > + ch = &gpadc->chans[i]; > + iio_chan = &iio_chans[i]; > + > + ret = ab8500_gpadc_parse_channel(gpadc->dev, child, ch, > + iio_chan); > + if (ret) { > + of_node_put(child); > + return ret; > + } > + i++; > + } > + gpadc->nchans = nchans; > + *chans_parsed = iio_chans; > + *nchans_parsed = nchans; > + > + return 0; > +} > + > +static int ab8500_gpadc_probe(struct platform_device *pdev) > +{ > + int ret = 0; Looks like this is set below in all paths that use it. > + struct ab8500_gpadc *gpadc; > + struct iio_dev *indio_dev; > + struct device *dev = &pdev->dev; > + struct device_node *np = pdev->dev.of_node; > + struct iio_chan_spec *iio_chans; > + unsigned int n_iio_chans; > + > + indio_dev = devm_iio_device_alloc(dev, sizeof(*gpadc)); > + if (!indio_dev) > + return -ENOMEM; nitpick: Blank line here. > + platform_set_drvdata(pdev, indio_dev); > + gpadc = iio_priv(indio_dev); > + > + gpadc->dev = dev; > + gpadc->ab8500 = dev_get_drvdata(dev->parent); > + > + ret = ab8500_gpadc_parse_channels(gpadc, np, &iio_chans, &n_iio_chans); > + if (ret) > + return ret; > + > + gpadc->irq_sw = platform_get_irq_byname(pdev, "SW_CONV_END"); > + if (gpadc->irq_sw < 0) { > + dev_err(dev, "failed to get platform sw_conv_end irq\n"); > + return gpadc->irq_sw; > + } > + > + gpadc->irq_hw = platform_get_irq_byname(pdev, "HW_CONV_END"); > + if (gpadc->irq_hw < 0) { > + dev_err(dev, "failed to get platform hw_conv_end irq\n"); > + return gpadc->irq_hw; > + } > + > + /* Initialize completion used to notify completion of conversion */ > + init_completion(&gpadc->complete); > + > + /* Request interrupts */ > + ret = devm_request_threaded_irq(dev, > + gpadc->irq_sw, NULL, > + ab8500_bm_gpadcconvend_handler, > + IRQF_NO_SUSPEND | IRQF_ONESHOT, > + "ab8500-gpadc-sw", > + gpadc); > + if (ret < 0) { > + dev_err(dev, > + "failed to request sw conversion irq %d\n", > + gpadc->irq_sw); > + return ret; > + } > + > + ret = devm_request_threaded_irq(dev, > + gpadc->irq_hw, NULL, > + ab8500_bm_gpadcconvend_handler, Seems to be under 80 chars when aligned with the opening bracket, so nice to do that where we can. > + IRQF_NO_SUSPEND | IRQF_ONESHOT, > + "ab8500-gpadc-hw", > + gpadc); > + if (ret < 0) { > + dev_err(dev, > + "Failed to request hw conversion irq: %d\n", > + gpadc->irq_hw); > + return ret; > + } > + > + /* The VTVout LDO used to power the AB8500 GPADC */ > + gpadc->vddadc = devm_regulator_get(dev, "vddadc"); > + if (IS_ERR(gpadc->vddadc)) { > + ret = PTR_ERR(gpadc->vddadc); > + dev_err(dev, "failed to get vddadc\n"); > + return ret; > + } > + > + ret = regulator_enable(gpadc->vddadc); > + if (ret) { > + dev_err(dev, "failed to enable vddadc: %d\n", ret); > + return ret; > + } > + > + /* Enable runtime PM */ > + pm_runtime_get_noresume(dev); > + pm_runtime_set_active(dev); > + pm_runtime_enable(dev); > + pm_runtime_set_autosuspend_delay(dev, GPADC_AUDOSUSPEND_DELAY); > + pm_runtime_use_autosuspend(dev); > + > + ab8500_gpadc_read_calibration_data(gpadc); > + > + pm_runtime_put(dev); > + > + indio_dev->dev.parent = dev; > + indio_dev->dev.of_node = np; > + indio_dev->name = "ab8500-gpadc"; > + indio_dev->modes = INDIO_DIRECT_MODE; > + indio_dev->info = &ab8500_gpadc_info; > + indio_dev->channels = iio_chans; > + indio_dev->num_channels = n_iio_chans; > + > + ret = devm_iio_device_register(dev, indio_dev); > + if (ret) > + goto out_dis_pm; > + > + dev_info(dev, "AB8500 GPADC initialized\n"); I'm slightly against this sort of noise, but if you are particularly attached to it will let it go. > + > + return 0; > + > +out_dis_pm: > + pm_runtime_get_sync(dev); > + pm_runtime_put_noidle(dev); > + pm_runtime_disable(dev); > + regulator_disable(gpadc->vddadc); > + > + return ret; > +} > + > +static int ab8500_gpadc_remove(struct platform_device *pdev) > +{ > + struct iio_dev *indio_dev = platform_get_drvdata(pdev); > + struct ab8500_gpadc *gpadc = iio_priv(indio_dev); > + > + pm_runtime_get_sync(gpadc->dev); > + pm_runtime_put_noidle(gpadc->dev); > + pm_runtime_disable(gpadc->dev); > + regulator_disable(gpadc->vddadc); > + > + return 0; > +} > + > +static const struct dev_pm_ops ab8500_gpadc_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, > + pm_runtime_force_resume) > + SET_RUNTIME_PM_OPS(ab8500_gpadc_runtime_suspend, > + ab8500_gpadc_runtime_resume, > + NULL) > +}; > + > +static struct platform_driver ab8500_gpadc_driver = { > + .probe = ab8500_gpadc_probe, > + .remove = ab8500_gpadc_remove, > + .driver = { > + .name = "ab8500-gpadc", > + .pm = &ab8500_gpadc_pm_ops, > + }, > +}; > +builtin_platform_driver(ab8500_gpadc_driver);