Re: [PATCH] iio: adc: sc27xx: Change to polling mode to read data

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 25 Jul 2019 14:33:50 +0800
Baolin Wang <baolin.wang@xxxxxxxxxx> wrote:

> From: Freeman Liu <freeman.liu@xxxxxxxxxx>
> 
> On Spreadtrum platform, the headphone will read one ADC channel multiple
> times to identify the headphone type, and the headphone identification is
> sensitive of the ADC reading time. And we found it will take longer time
> to reading ADC data by using interrupt mode comparing with the polling
> mode, thus we should change to polling mode to improve the efficiency
> of reading data, which can identify the headphone type successfully.
> 
> Signed-off-by: Freeman Liu <freeman.liu@xxxxxxxxxx>
> Signed-off-by: Baolin Wang <baolin.wang@xxxxxxxxxx>

Hi,

My concerns with this sort of approach is that we may be sacrificing power
efficiency for some usecases to support one demanding one.

The maximum sleep time is 1 second (I think) which is probably too long
to poll a register for in general.

Is there some way we can bound that time and perhaps switch between
interrupt and polling modes depending on how long we expect to wait?

Thanks,

Jonathan

> ---
>  drivers/iio/adc/sc27xx_adc.c |   81 ++++++++++++++----------------------------
>  1 file changed, 27 insertions(+), 54 deletions(-)
> 
> diff --git a/drivers/iio/adc/sc27xx_adc.c b/drivers/iio/adc/sc27xx_adc.c
> index f7f7a189..ea864290 100644
> --- a/drivers/iio/adc/sc27xx_adc.c
> +++ b/drivers/iio/adc/sc27xx_adc.c
> @@ -3,7 +3,6 @@
>  
>  #include <linux/hwspinlock.h>
>  #include <linux/iio/iio.h>
> -#include <linux/interrupt.h>
>  #include <linux/module.h>
>  #include <linux/nvmem-consumer.h>
>  #include <linux/of.h>
> @@ -46,14 +45,18 @@
>  /* Bits definitions for SC27XX_ADC_INT_CLR registers */
>  #define SC27XX_ADC_IRQ_CLR		BIT(0)
>  
> +/* Bits definitions for SC27XX_ADC_INT_RAW registers */
> +#define SC27XX_ADC_IRQ_RAW		BIT(0)
> +
>  /* Mask definition for SC27XX_ADC_DATA register */
>  #define SC27XX_ADC_DATA_MASK		GENMASK(11, 0)
>  
>  /* Timeout (ms) for the trylock of hardware spinlocks */
>  #define SC27XX_ADC_HWLOCK_TIMEOUT	5000
>  
> -/* Timeout (ms) for ADC data conversion according to ADC datasheet */
> -#define SC27XX_ADC_RDY_TIMEOUT		100
> +/* Timeout (us) for ADC data conversion according to ADC datasheet */
> +#define SC27XX_ADC_RDY_TIMEOUT		1000000

This is 10 x the value I think...

> +#define SC27XX_ADC_POLL_RAW_STATUS	500
>  
>  /* Maximum ADC channel number */
>  #define SC27XX_ADC_CHANNEL_MAX		32
> @@ -72,10 +75,8 @@ struct sc27xx_adc_data {
>  	 * subsystems which will access the unique ADC controller.
>  	 */
>  	struct hwspinlock *hwlock;
> -	struct completion completion;
>  	int channel_scale[SC27XX_ADC_CHANNEL_MAX];
>  	u32 base;
> -	int value;
>  	int irq;
>  };
>  
> @@ -188,9 +189,7 @@ static int sc27xx_adc_read(struct sc27xx_adc_data *data, int channel,
>  			   int scale, int *val)
>  {
>  	int ret;
> -	u32 tmp;
> -
> -	reinit_completion(&data->completion);
> +	u32 tmp, value, status;
>  
>  	ret = hwspin_lock_timeout_raw(data->hwlock, SC27XX_ADC_HWLOCK_TIMEOUT);
>  	if (ret) {
> @@ -203,6 +202,11 @@ static int sc27xx_adc_read(struct sc27xx_adc_data *data, int channel,
>  	if (ret)
>  		goto unlock_adc;
>  
> +	ret = regmap_update_bits(data->regmap, data->base + SC27XX_ADC_INT_CLR,
> +				 SC27XX_ADC_IRQ_CLR, SC27XX_ADC_IRQ_CLR);
> +	if (ret)
> +		goto disable_adc;
> +
>  	/* Configure the channel id and scale */
>  	tmp = (scale << SC27XX_ADC_SCALE_SHIFT) & SC27XX_ADC_SCALE_MASK;
>  	tmp |= channel & SC27XX_ADC_CHN_ID_MASK;
> @@ -226,15 +230,22 @@ static int sc27xx_adc_read(struct sc27xx_adc_data *data, int channel,
>  	if (ret)
>  		goto disable_adc;
>  
> -	ret = wait_for_completion_timeout(&data->completion,
> -				msecs_to_jiffies(SC27XX_ADC_RDY_TIMEOUT));
> -	if (!ret) {
> -		dev_err(data->dev, "read ADC data timeout\n");
> -		ret = -ETIMEDOUT;
> -	} else {
> -		ret = 0;
> +	ret = regmap_read_poll_timeout(data->regmap,
> +				       data->base + SC27XX_ADC_INT_RAW,
> +				       status, (status & SC27XX_ADC_IRQ_RAW),
> +				       SC27XX_ADC_POLL_RAW_STATUS,
> +				       SC27XX_ADC_RDY_TIMEOUT);
> +	if (ret) {
> +		dev_err(data->dev, "read adc timeout, status = 0x%x\n", status);
> +		goto disable_adc;
>  	}
>  
> +	ret = regmap_read(data->regmap, data->base + SC27XX_ADC_DATA, &value);
> +	if (ret)
> +		goto disable_adc;
> +
> +	value &= SC27XX_ADC_DATA_MASK;
> +
>  disable_adc:
>  	regmap_update_bits(data->regmap, data->base + SC27XX_ADC_CTL,
>  			   SC27XX_ADC_EN, 0);
> @@ -242,32 +253,11 @@ static int sc27xx_adc_read(struct sc27xx_adc_data *data, int channel,
>  	hwspin_unlock_raw(data->hwlock);
>  
>  	if (!ret)
> -		*val = data->value;
> +		*val = value;
>  
>  	return ret;
>  }
>  
> -static irqreturn_t sc27xx_adc_isr(int irq, void *dev_id)
> -{
> -	struct sc27xx_adc_data *data = dev_id;
> -	int ret;
> -
> -	ret = regmap_update_bits(data->regmap, data->base + SC27XX_ADC_INT_CLR,
> -				 SC27XX_ADC_IRQ_CLR, SC27XX_ADC_IRQ_CLR);
> -	if (ret)
> -		return IRQ_RETVAL(ret);
> -
> -	ret = regmap_read(data->regmap, data->base + SC27XX_ADC_DATA,
> -			  &data->value);
> -	if (ret)
> -		return IRQ_RETVAL(ret);
> -
> -	data->value &= SC27XX_ADC_DATA_MASK;
> -	complete(&data->completion);
> -
> -	return IRQ_HANDLED;
> -}
> -
>  static void sc27xx_adc_volt_ratio(struct sc27xx_adc_data *data,
>  				  int channel, int scale,
>  				  u32 *div_numerator, u32 *div_denominator)
> @@ -454,11 +444,6 @@ static int sc27xx_adc_enable(struct sc27xx_adc_data *data)
>  	if (ret)
>  		goto disable_adc;
>  
> -	ret = regmap_update_bits(data->regmap, data->base + SC27XX_ADC_INT_EN,
> -				 SC27XX_ADC_IRQ_EN, SC27XX_ADC_IRQ_EN);
> -	if (ret)
> -		goto disable_clk;
> -
>  	/* ADC channel scales' calibration from nvmem device */
>  	ret = sc27xx_adc_scale_calibration(data, true);
>  	if (ret)
> @@ -484,9 +469,6 @@ static void sc27xx_adc_disable(void *_data)
>  {
>  	struct sc27xx_adc_data *data = _data;
>  
> -	regmap_update_bits(data->regmap, data->base + SC27XX_ADC_INT_EN,
> -			   SC27XX_ADC_IRQ_EN, 0);
> -
>  	/* Disable ADC work clock and controller clock */
>  	regmap_update_bits(data->regmap, SC27XX_ARM_CLK_EN,
>  			   SC27XX_CLK_ADC_EN | SC27XX_CLK_ADC_CLK_EN, 0);
> @@ -553,7 +535,6 @@ static int sc27xx_adc_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> -	init_completion(&sc27xx_data->completion);
>  	sc27xx_data->dev = &pdev->dev;
>  
>  	ret = sc27xx_adc_enable(sc27xx_data);
> @@ -569,14 +550,6 @@ static int sc27xx_adc_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> -	ret = devm_request_threaded_irq(&pdev->dev, sc27xx_data->irq, NULL,
> -					sc27xx_adc_isr, IRQF_ONESHOT,
> -					pdev->name, sc27xx_data);
> -	if (ret) {
> -		dev_err(&pdev->dev, "failed to request ADC irq\n");
> -		return ret;
> -	}
> -
>  	indio_dev->dev.parent = &pdev->dev;
>  	indio_dev->name = dev_name(&pdev->dev);
>  	indio_dev->modes = INDIO_DIRECT_MODE;




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux