Re: [PATCH v3 5/7] staging: iio: ad5933: add ABI documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Mar 10, 2019 at 7:47 PM Marcelo Schmitt
<marcelo.schmitt1@xxxxxxxxx> wrote:
>
> Add an ABI documentation for the ad5933 driver.

There's already an ABI documentation for this driver.
See:
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git/tree/drivers/staging/iio/Documentation/sysfs-bus-iio-impedance-analyzer-ad5933

Apologies for not mentioning this sooner.

Could you check for other references for ad5933 in the kernel (in staging) ?
I don't think I missed other stuff, but it's good to check.

>
> Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@xxxxxxxxx>
> ---
>  .../ABI/testing/sysfs-bus-iio-ad5933          | 39 +++++++++++++++++++
>  1 file changed, 39 insertions(+)
>  create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-ad5933
>
> diff --git a/Documentation/ABI/testing/sysfs-bus-iio-ad5933 b/Documentation/ABI/testing/sysfs-bus-iio-ad5933
> new file mode 100644
> index 000000000000..8a60dd178b1f
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-bus-iio-ad5933
> @@ -0,0 +1,39 @@
> +What:/sys/bus/iio/devices/iio:deviceX/out_voltage0_freq_start
> +Date:          March 2019
> +KernelVersion: Kernel 4.19
> +Contact:       linux-iio@xxxxxxxxxxxxxxx
> +Description:
> +               The start frequency. Set this to define the frequency point at
> +               which the device should start the next frequency sweep.
> +
> +What:/sys/bus/iio/devices/iio:deviceX/out_voltage0_freq_increment
> +Date:          March 2019
> +KernelVersion: Kernel 4.19
> +Contact:       linux-iio@xxxxxxxxxxxxxxx
> +Description:
> +               The frequency sweep increment. Set this to define the amount by
> +               which the frequency is incremented after each scan point. After
> +               the measurement at a frequency point is completed, the next
> +               measurement will be made at a frequency point
> +               'frequency increment'Hz higher than the previous one unless a
> +               repeat frequency command is issued. This behavior will follow
> +               until the defined number of frequency points have been measured
> +               or frequency sweep is somewhat reset.
> +
> +What:/sys/bus/iio/devices/iio:deviceX/out_voltage0_freq_points
> +Date:          March 2019
> +KernelVersion: Kernel 4.19
> +Contact:       linux-iio@xxxxxxxxxxxxxxx
> +Description:
> +               The number of increments. This defines the number of frequency
> +               points in the frequency sweep.
> +
> +What:/sys/bus/iio/devices/iio:deviceX/out_voltage0_settling_cycles
> +Date:          March 2019
> +KernelVersion: Kernel 4.19
> +Contact:       linux-iio@xxxxxxxxxxxxxxx
> +Description:
> +               Number of settling time cycles. This sets the delay between a
> +               start frequency sweep/increment frequency /repeat frequency to
> +               be proportional to the excitation signal frequency times the
> +               number of settling time cycles.
> --
> 2.20.1
>



[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux