On Thu, 2 Aug 2018 20:18:53 -0400 Brian Masney <masneyb@xxxxxxxxxxxxx> wrote: > This patch adds device tree bindings for the mpu6515 to the LG Nexus 5 > (hammerhead) phone. Confirmed that the gyroscope / accelerometer > (mpu6515), magnetometer (ak8963), and temperature / pressure (bmp280) > sensors are available on the phone. > > Interrupts are not working properly on the ak8963 magnetometer so they > are currently not configured. > > The bmp280 retuns temperature/pressure measurement skipped errors but > will reliably work if I run: > > echo 1 > in_pressure_oversampling_ratio > echo 1 > in_temp_oversampling_ratio > > Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx> > Signed-off-by: Jonathan Marek <jonathan@xxxxxxxx> I've queued up the regulator patch for IIO but it won't make the coming merge window. There is no dependence between this and that patch, but I would assume the hardware won't work until both are present. Jonathan > --- > I'll send follow up patch(es) once I investigate why the skipped errors > are occurring with the bmp280 with the default oversampling ratios. > > .../qcom-msm8974-lge-nexus5-hammerhead.dts | 56 +++++++++++++++++++ > arch/arm/boot/dts/qcom-msm8974.dtsi | 11 ++++ > 2 files changed, 67 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts > index c2dc9d09484a..928affae1885 100644 > --- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts > +++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts > @@ -241,6 +241,24 @@ > bias-pull-up; > }; > }; > + > + i2c12_pins: i2c12 { > + mux { > + pins = "gpio87", "gpio88"; > + function = "blsp_i2c12"; > + drive-strength = <2>; > + bias-disable; > + }; > + }; > + > + mpu6515_pin: mpu6515 { > + irq { > + pins = "gpio73"; > + function = "gpio"; > + bias-disable; > + input-enable; > + }; > + }; > }; > > sdhci@f9824900 { > @@ -277,6 +295,44 @@ > linux,code = <KEY_VOLUMEDOWN>; > }; > }; > + > + i2c@f9968000 { > + status = "ok"; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c12_pins>; > + clock-frequency = <100000>; > + qcom,src-freq = <50000000>; > + > + mpu6515@68 { > + compatible = "invensense,mpu6515"; > + reg = <0x68>; > + interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>; > + vddio-supply = <&pm8941_lvs1>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&mpu6515_pin>; > + > + i2c-gate { > + #address-cells = <1>; > + #size-cells = <0>; > + ak8963@f { > + compatible = "asahi-kasei,ak8963"; > + reg = <0x0f>; > + // Currently only works in polling mode. > + // gpios = <&msmgpio 61 0>; > + vid-supply = <&pm8941_lvs1>; > + vdd-supply = <&pm8941_l17>; > + }; > + > + bmp280@76 { > + compatible = "bosch,bmp280"; > + reg = <0x76>; > + vdda-supply = <&pm8941_lvs1>; > + vddd-supply = <&pm8941_l17>; > + }; > + }; > + }; > + }; > }; > > &spmi_bus { > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi > index d9019a49b292..cebb6ae9143a 100644 > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi > @@ -737,6 +737,17 @@ > dma-names = "tx", "rx"; > }; > > + blsp_i2c12: i2c@f9968000 { > + status = "disabled"; > + compatible = "qcom,i2c-qup-v2.1.1"; > + reg = <0xf9968000 0x1000>; > + interrupts = <0 106 IRQ_TYPE_NONE>; > + clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; > + clock-names = "core", "iface"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > spmi_bus: spmi@fc4cf000 { > compatible = "qcom,spmi-pmic-arb"; > reg-names = "core", "intr", "cnfg"; -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html