On Wed, Jul 11, 2018 at 5:13 AM, Himanshu Jha <himanshujha199640@xxxxxxxxx> wrote: > Bosch BME680 is a 4-in-1 sensor with temperature, pressure, humidity > and gas sensing capability. It supports both I2C and SPI communication > protocol for effective data communication. > > The device supports two modes: > > 1. Sleep mode > 2. Forced mode > > The measurements only takes place when forced mode is triggered and a > single TPHG cycle is performed by the sensor. The sensor automatically > goes to sleep after afterwards. > > The device has various calibration constants/parameters programmed into > devices' non-volatile memory(NVM) during production and can't be altered > by the user. These constants are used in the compensation functions to > get the required compensated readings along with the raw data. The > compensation functions/algorithms are provided by Bosch Sensortec GmbH > via their API[1]. As these don't change during the measurement cycle, > therefore we read and store them at the probe. The default configs > supplied by Bosch are also set at probe. > > 0-day tested with build success. > > GSoC-2018: https://summerofcode.withgoogle.com/projects/#6691473790074880 > Mentor: Daniel Baluta > [1] https://github.com/BoschSensortec/BME680_driver > Datasheet: > https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME680-DS001-00.pdf > > Cc: Daniel Baluta <daniel.baluta@xxxxxxxxx> > Signed-off-by: Himanshu Jha <himanshujha199640@xxxxxxxxx> > --- > > v3: > -moved files to chemical directory instead of a dedicated directory. > -read calibration parameters serially with endian conversions. > -drop some return ret. > -removed few unnecessary casts safely. > -added 'u' suffix to explicitly specify unsigned for large values > and thereby fixing comiler warning. > -left aligned all comments. > -added a comment explaining heater stability failure. > > v2: > -Used devm_add_action() to add a generic remove method for > both I2C & SPI driver. > -Introduction of compensation functions. > -chip initialisation routines moved to respective I2C and SPI > driver. > -Introduction of gas sensing rountines. > -Simplified Kconfig to reduce various options. > > drivers/iio/chemical/Kconfig | 25 + > drivers/iio/chemical/Makefile | 3 + > drivers/iio/chemical/bme680.h | 99 ++++ > drivers/iio/chemical/bme680_core.c | 946 +++++++++++++++++++++++++++++++++++++ > drivers/iio/chemical/bme680_i2c.c | 83 ++++ > drivers/iio/chemical/bme680_spi.c | 123 +++++ > 6 files changed, 1279 insertions(+) > create mode 100644 drivers/iio/chemical/bme680.h > create mode 100644 drivers/iio/chemical/bme680_core.c > create mode 100644 drivers/iio/chemical/bme680_i2c.c > create mode 100644 drivers/iio/chemical/bme680_spi.c > > diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig > index 5cb5be7..24790a8 100644 > --- a/drivers/iio/chemical/Kconfig > +++ b/drivers/iio/chemical/Kconfig > @@ -21,6 +21,31 @@ config ATLAS_PH_SENSOR > To compile this driver as module, choose M here: the > module will be called atlas-ph-sensor. > > +config BME680 > + tristate "Bosch Sensortec BME680 sensor driver" > + depends on (I2C || SPI) > + select REGMAP > + select BME680_I2C if (I2C) > + select BME680_SPI if (SPI) Don't think you actually need parentheses around any of these, but of course then again doesn't hurt > + help > + Say yes here to build support for Bosch Sensortec BME680 sensor with > + temperature, pressure, humidity and gas sensing capability. > + > + This driver can also be built as a module. If so, the module for I2C > + would be called bme680_i2c and bme680_spi for SPI support. > + > +config BME680_I2C > + tristate > + depends on BME680 > + depends on I2C Wouldn't "depends on I2C && BME680" be cleaner? Maybe someone else here can tell me if I'm too nit-picky :) > + select REGMAP_I2C > + > +config BME680_SPI > + tristate > + depends on BME680 > + depends on SPI Same only with SPI > + select REGMAP_SPI > + > config CCS811 > tristate "AMS CCS811 VOC sensor" > depends on I2C > diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile > index a629b29..2f4c4ba 100644 > --- a/drivers/iio/chemical/Makefile > +++ b/drivers/iio/chemical/Makefile > @@ -4,6 +4,9 @@ > > # When adding new entries keep the list in alphabetical order > obj-$(CONFIG_ATLAS_PH_SENSOR) += atlas-ph-sensor.o > +obj-$(CONFIG_BME680) += bme680_core.o > +obj-$(CONFIG_BME680_I2C) += bme680_i2c.o > +obj-$(CONFIG_BME680_SPI) += bme680_spi.o > obj-$(CONFIG_CCS811) += ccs811.o > obj-$(CONFIG_IAQCORE) += ams-iaq-core.o > obj-$(CONFIG_VZ89X) += vz89x.o > diff --git a/drivers/iio/chemical/bme680.h b/drivers/iio/chemical/bme680.h > new file mode 100644 > index 0000000..80c4190 > --- /dev/null > +++ b/drivers/iio/chemical/bme680.h > @@ -0,0 +1,99 @@ > +/* SPDX-License-Identifier: GPL-2.0 */ > +#ifndef BME680_H_ > +#define BME680_H_ > + > +#define BME680_REG_CHIP_I2C_ID 0xD0 > +#define BME680_REG_CHIP_SPI_ID 0x50 > +#define BME680_CHIP_ID_VAL 0x61 > +#define BME680_REG_SOFT_RESET 0xE0 > +#define BME680_CMD_SOFTRESET 0xB6 > +#define BME680_REG_STATUS 0x73 > +#define BME680_SPI_MEM_PAGE_BIT BIT(4) > +#define BME680_SPI_MEM_PAGE_1_VAL 1 > + > +#define BME680_OSRS_TEMP_X(osrs_t) ((osrs_t) << 5) > +#define BME680_OSRS_PRESS_X(osrs_p) ((osrs_p) << 2) > +#define BME680_OSRS_HUMID_X(osrs_h) ((osrs_h) << 0) > + > +#define BME680_REG_TEMP_MSB 0x22 > +#define BME680_REG_PRESS_MSB 0x1F > +#define BM6880_REG_HUMIDITY_MSB 0x25 > +#define BME680_REG_GAS_MSB 0x2A > +#define BME680_REG_GAS_R_LSB 0x2B > +#define BME680_GAS_STAB_BIT BIT(4) > + > +#define BME680_REG_CTRL_HUMIDITY 0x72 > +#define BME680_OSRS_HUMIDITY_MASK GENMASK(2, 0) > + > +#define BME680_REG_CTRL_MEAS 0x74 > +#define BME680_OSRS_TEMP_MASK GENMASK(7, 5) > +#define BME680_OSRS_PRESS_MASK GENMASK(4, 2) > +#define BME680_MODE_MASK GENMASK(1, 0) > + > +#define BME680_MODE_FORCED BIT(0) > +#define BME680_MODE_SLEEP 0 > + > +#define BME680_REG_CONFIG 0x75 > +#define BME680_FILTER_MASK GENMASK(4, 2) > +#define BME680_FILTER_COEFF BIT(1) > + > +/* TEMP/PRESS/HUMID reading skipped */ > +#define BME680_MEAS_SKIPPED 0x8000 > + > +#define BME680_MAX_OVERFLOW_VAL 0x40000000 > +#define BME680_HUM_REG_SHIFT_VAL 4 > +#define BME680_BIT_H1_DATA_MSK 0x0F > + > +#define BME680_REG_RES_HEAT_RANGE 0x02 > +#define BME680_RHRANGE_MSK 0x30 > +#define BME680_REG_RES_HEAT_VAL 0x00 > +#define BME680_REG_RANGE_SW_ERR 0x04 > +#define BME680_RSERROR_MSK 0xF0 > +#define BME680_REG_RES_HEAT_0 0x5A > +#define BME680_REG_GAS_WAIT_0 0x64 > +#define BME680_GAS_RANGE_MASK 0x0F > +#define BME680_ADC_GAS_RES_SHIFT 6 > +#define BME680_AMB_TEMP 25 > + > +#define BME680_REG_CTRL_GAS_1 0x71 > +#define BME680_RUN_GAS_MASK BIT(4) > +#define BME680_NB_CONV_MASK GENMASK(3, 0) > +#define BME680_RUN_GAS_EN BIT(4) > +#define BME680_NB_CONV_0 0 > + > +#define BME680_REG_MEAS_STAT_0 0x1D > +#define BME680_GAS_MEAS_BIT BIT(6) > + > +/* Calibration Parameters */ > +#define BME680_T2_LSB_REG 0x8A > +#define BME680_T3_REG 0x8C > +#define BME680_P1_LSB_REG 0x8E > +#define BME680_P2_LSB_REG 0x90 > +#define BME680_P3_REG 0x92 > +#define BME680_P4_LSB_REG 0x94 > +#define BME680_P5_LSB_REG 0x96 > +#define BME680_P7_REG 0x98 > +#define BME680_P6_REG 0x99 > +#define BME680_P8_LSB_REG 0x9C > +#define BME680_P9_LSB_REG 0x9E > +#define BME680_P10_REG 0xA0 > +#define BME680_H2_LSB_REG 0xE2 > +#define BME680_H2_MSB_REG 0xE1 > +#define BME680_H1_MSB_REG 0xE3 > +#define BME680_H1_LSB_REG 0xE2 > +#define BME680_H3_REG 0xE4 > +#define BME680_H4_REG 0xE5 > +#define BME680_H5_REG 0xE6 > +#define BME680_H6_REG 0xE7 > +#define BME680_H7_REG 0xE8 > +#define BME680_T1_LSB_REG 0xE9 > +#define BME680_GH2_LSB_REG 0xEB > +#define BME680_GH1_REG 0xED > +#define BME680_GH3_REG 0xEE > + > +extern const struct regmap_config bme680_regmap_config; > + > +int bme680_core_probe(struct device *dev, struct regmap *regmap, > + const char *name); > + > +#endif /* BME680_H_ */ > diff --git a/drivers/iio/chemical/bme680_core.c b/drivers/iio/chemical/bme680_core.c > new file mode 100644 > index 0000000..8dd789e > --- /dev/null > +++ b/drivers/iio/chemical/bme680_core.c > @@ -0,0 +1,946 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Bosch BME680 - Temperature, Pressure, Humidity & Gas Sensor > + * > + * Copyright (C) 2017 - 2018 Bosch Sensortec GmbH > + * Copyright (C) 2018 Himanshu Jha <himanshujha199640@xxxxxxxxx> > + */ > +#include <linux/acpi.h> > +#include <linux/device.h> > +#include <linux/module.h> > +#include <linux/log2.h> > +#include <linux/regmap.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > + > +#include "bme680.h" > + > +struct bme680_calib { > + u16 par_t1; > + s16 par_t2; > + s8 par_t3; > + u16 par_p1; > + s16 par_p2; > + s8 par_p3; > + s16 par_p4; > + s16 par_p5; > + s8 par_p6; > + s8 par_p7; > + s16 par_p8; > + s16 par_p9; > + u8 par_p10; > + u16 par_h1; > + u16 par_h2; > + s8 par_h3; > + s8 par_h4; > + s8 par_h5; > + s8 par_h6; > + s8 par_h7; > + s8 par_gh1; > + s16 par_gh2; > + s8 par_gh3; > + u8 res_heat_range; > + s8 res_heat_val; > + s8 range_sw_err; > +}; > + > +struct bme680_data { > + struct regmap *regmap; > + struct bme680_calib bme680; > + u8 oversampling_temp; > + u8 oversampling_press; > + u8 oversampling_humid; > + u16 heater_dur; > + u16 heater_temp; > + /* > + * Carryover value from temperature conversion, used in pressure > + * and humidity compensation calculations. > + */ > + s32 t_fine; > +}; > + > +const struct regmap_config bme680_regmap_config = { > + .reg_bits = 8, > + .val_bits = 8, > +}; > +EXPORT_SYMBOL(bme680_regmap_config); > + > +static const struct iio_chan_spec bme680_channels[] = { > + { > + .type = IIO_TEMP, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | > + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), > + }, > + { > + .type = IIO_PRESSURE, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | > + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), > + }, > + { > + .type = IIO_HUMIDITYRELATIVE, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | > + BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), > + }, > + { > + .type = IIO_RESISTANCE, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), > + }, > +}; > + > +static const int bme680_oversampling_avail[] = { 1, 2, 4, 8, 16 }; > + > +static int bme680_read_calib(struct bme680_data *data, > + struct bme680_calib *calib) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + unsigned int tmp, tmp_msb, tmp_lsb; > + int ret; > + __le16 buf; > + > + /* Temperature related coefficients */ > + ret = regmap_bulk_read(data->regmap, BME680_T1_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_T1_LSB_REG\n"); > + return ret; > + } > + calib->par_t1 = le16_to_cpu(buf); > + > + ret = regmap_bulk_read(data->regmap, BME680_T2_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_T2_LSB_REG\n"); > + return ret; > + } > + calib->par_t2 = le16_to_cpu(buf); > + > + ret = regmap_read(data->regmap, BME680_T3_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_T3_REG\n"); > + return ret; > + } > + calib->par_t3 = tmp; > + > + /* Pressure related coefficients */ > + ret = regmap_bulk_read(data->regmap, BME680_P1_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P1_LSB_REG\n"); > + return ret; > + } > + calib->par_p1 = le16_to_cpu(buf); > + > + ret = regmap_bulk_read(data->regmap, BME680_P2_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P2_LSB_REG\n"); > + return ret; > + } > + calib->par_p2 = le16_to_cpu(buf); > + > + ret = regmap_read(data->regmap, BME680_P3_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P3_REG\n"); > + return ret; > + } > + calib->par_p3 = tmp; > + > + ret = regmap_bulk_read(data->regmap, BME680_P4_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P4_LSB_REG\n"); > + return ret; > + } > + calib->par_p4 = le16_to_cpu(buf); > + > + ret = regmap_bulk_read(data->regmap, BME680_P5_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P5_LSB_REG\n"); > + return ret; > + } > + calib->par_p5 = le16_to_cpu(buf); > + > + ret = regmap_read(data->regmap, BME680_P6_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P6_REG\n"); > + return ret; > + } > + calib->par_p6 = tmp; > + > + ret = regmap_read(data->regmap, BME680_P7_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P7_REG\n"); > + return ret; > + } > + calib->par_p7 = tmp; > + > + ret = regmap_bulk_read(data->regmap, BME680_P8_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P8_LSB_REG\n"); > + return ret; > + } > + calib->par_p8 = le16_to_cpu(buf); > + > + ret = regmap_bulk_read(data->regmap, BME680_P9_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P9_LSB_REG\n"); > + return ret; > + } > + calib->par_p9 = le16_to_cpu(buf); > + > + ret = regmap_read(data->regmap, BME680_P10_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_P10_REG\n"); > + return ret; > + } > + calib->par_p10 = tmp; > + > + /* Humidity related coefficients */ > + ret = regmap_read(data->regmap, BME680_H1_MSB_REG, &tmp_msb); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H1_MSB_REG\n"); > + return ret; > + } > + > + ret = regmap_read(data->regmap, BME680_H1_LSB_REG, &tmp_lsb); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H1_LSB_REG\n"); > + return ret; > + } > + > + calib->par_h1 = (tmp_msb << BME680_HUM_REG_SHIFT_VAL) | > + (tmp_lsb & BME680_BIT_H1_DATA_MSK); > + > + ret = regmap_read(data->regmap, BME680_H2_MSB_REG, &tmp_msb); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H2_MSB_REG\n"); > + return ret; > + } > + > + ret = regmap_read(data->regmap, BME680_H2_LSB_REG, &tmp_lsb); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H2_LSB_REG\n"); > + return ret; > + } > + > + calib->par_h2 = (tmp_msb << BME680_HUM_REG_SHIFT_VAL) | > + (tmp_lsb >> BME680_HUM_REG_SHIFT_VAL); > + > + ret = regmap_read(data->regmap, BME680_H3_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H3_REG\n"); > + return ret; > + } > + calib->par_h3 = tmp; > + > + ret = regmap_read(data->regmap, BME680_H4_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H4_REG\n"); > + return ret; > + } > + calib->par_h4 = tmp; > + > + ret = regmap_read(data->regmap, BME680_H5_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H5_REG\n"); > + return ret; > + } > + calib->par_h5 = tmp; > + > + ret = regmap_read(data->regmap, BME680_H6_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H6_REG\n"); > + return ret; > + } > + calib->par_h6 = tmp; > + > + ret = regmap_read(data->regmap, BME680_H7_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_H7_REG\n"); > + return ret; > + } > + calib->par_h7 = tmp; > + > + /* Gas heater related coefficients */ > + ret = regmap_read(data->regmap, BME680_GH1_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_GH1_REG\n"); > + return ret; > + } > + calib->par_gh1 = tmp; > + > + ret = regmap_bulk_read(data->regmap, BME680_GH2_LSB_REG, > + (u8 *) &buf, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_GH2_LSB_REG\n"); > + return ret; > + } > + calib->par_gh2 = le16_to_cpu(buf); > + > + ret = regmap_read(data->regmap, BME680_GH3_REG, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read BME680_GH3_REG\n"); > + return ret; > + } > + calib->par_gh3 = tmp; > + > + /* Other coefficients */ > + ret = regmap_read(data->regmap, BME680_REG_RES_HEAT_RANGE, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read resistance heat range\n"); > + return ret; > + } > + calib->res_heat_range = (tmp & BME680_RHRANGE_MSK) / 16; > + > + ret = regmap_read(data->regmap, BME680_REG_RES_HEAT_VAL, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read resistance heat value\n"); > + return ret; > + } > + calib->res_heat_val = tmp; > + > + ret = regmap_read(data->regmap, BME680_REG_RANGE_SW_ERR, &tmp); > + if (ret < 0) { > + dev_err(dev, "failed to read range software error\n"); > + return ret; > + } > + calib->range_sw_err = (tmp & BME680_RSERROR_MSK) / 16; > + > + return 0; > +} > + > +/* Taken from Bosch BME680 API */ > +static s32 bme680_compensate_temp(struct bme680_data *data, > + s32 adc_temp) > +{ > + struct bme680_calib *calib = &data->bme680; > + s64 var1, var2, var3, calc_temp; > + > + var1 = ((s32) adc_temp >> 3) - ((s32) calib->par_t1 << 1); > + var2 = (var1 * (s32) calib->par_t2) >> 11; > + var3 = ((var1 >> 1) * (var1 >> 1)) >> 12; > + var3 = ((var3) * ((s32) calib->par_t3 << 4)) >> 14; > + data->t_fine = (s32) (var2 + var3); > + calc_temp = (s16) (((data->t_fine * 5) + 128) >> 8); > + > + return calc_temp; > +} > + > +/* Taken from Bosch BME680 API */ > +static u32 bme680_compensate_press(struct bme680_data *data, > + u32 adc_press) > +{ > + struct bme680_calib *calib = &data->bme680; > + s32 var1, var2, var3, press_comp; > + > + var1 = (((s32)data->t_fine) >> 1) - 64000; > + var2 = ((((var1 >> 2) * (var1 >> 2)) >> 11) * (s32)calib->par_p6) >> 2; > + var2 = var2 + ((var1 * (s32)calib->par_p5) << 1); > + var2 = (var2 >> 2) + ((s32)calib->par_p4 << 16); > + var1 = (((((var1 >> 2) * (var1 >> 2)) >> 13) * > + ((s32)calib->par_p3 << 5)) >> 3) + > + (((s32)calib->par_p2 * var1) >> 1); > + var1 = var1 >> 18; > + var1 = ((32768 + var1) * (s32)calib->par_p1) >> 15; > + press_comp = 1048576 - adc_press; > + press_comp = ((press_comp - (var2 >> 12)) * 3125); > + > + if (press_comp >= BME680_MAX_OVERFLOW_VAL) > + press_comp = ((press_comp / (u32)var1) << 1); > + else > + press_comp = ((press_comp << 1) / (u32)var1); > + > + var1 = ((s32)calib->par_p9 * (((press_comp >> 3) * > + (press_comp >> 3)) >> 13)) >> 12; > + var2 = ((press_comp >> 2) * (s32)calib->par_p8) >> 13; > + var3 = ((press_comp >> 8) * (press_comp >> 8) * > + (press_comp >> 8) * calib->par_p10) >> 17; > + > + press_comp += ((var1 + var2 + var3 + ((s32)calib->par_p7 << 7)) >> 4); > + > + return press_comp; > +} > + > +/* Taken from Bosch BME680 API */ > +static u32 bme680_compensate_humid(struct bme680_data *data, > + u16 adc_humid) > +{ > + struct bme680_calib *calib = &data->bme680; > + s32 var1, var2, var3, var4, var5, var6, temp_scaled, calc_hum; > + > + temp_scaled = (((s32) data->t_fine * 5) + 128) >> 8; > + var1 = (adc_humid - ((s32) ((s32) calib->par_h1 * 16))) - > + (((temp_scaled * (s32) calib->par_h3) / 100) >> 1); > + var2 = ((s32) calib->par_h2 * (((temp_scaled * (s32) calib->par_h4) / > + ((s32) 100)) + (((temp_scaled * ((temp_scaled * > + (s32) calib->par_h5) / 100)) >> 6) / 100) + > + (s32) (1 << 14))) >> 10; > + var3 = var1 * var2; > + var4 = (s32) calib->par_h6 << 7; > + var4 = (var4 + ((temp_scaled * (s32) calib->par_h7) / 100)) >> 4; > + var5 = ((var3 >> 14) * (var3 >> 14)) >> 10; > + var6 = (var4 * var5) >> 1; > + calc_hum = (((var3 + var6) >> 10) * 1000) >> 12; > + > + if (calc_hum > 100000) /* Cap at 100%rH */ > + calc_hum = 100000; > + else if (calc_hum < 0) > + calc_hum = 0; > + > + return calc_hum; > +} > + > +/* Taken from Bosch BME680 API */ > +static u32 bme680_compensate_gas(struct bme680_data *data, u16 gas_res_adc, > + u8 gas_range) > +{ > + struct bme680_calib *calib = &data->bme680; > + s64 var1; > + u64 var2; > + s64 var3; > + u32 calc_gas_res; > + > + /* Look up table 1 for the possible gas range values */ > + u32 lookupTable1[16] = {2147483647u, 2147483647u, 2147483647u, > + 2147483647u, 2147483647u, 2126008810u, > + 2147483647u, 2130303777u, 2147483647u, > + 2147483647u, 2143188679u, 2136746228u, > + 2147483647u, 2126008810u, 2147483647u, > + 2147483647u}; > + /* Look up table 2 for the possible gas range values */ > + u32 lookupTable2[16] = {4096000000u, 2048000000u, 1024000000u, > + 512000000u, 255744255u, 127110228u, 64000000u, > + 32258064u, 16016016u, 8000000u, 4000000u, > + 2000000u, 1000000u, 500000u, 250000u, 125000u}; > + > + var1 = ((1340 + (5 * (s64) calib->range_sw_err)) * > + ((s64) lookupTable1[gas_range])) >> 16; > + var2 = (((s64) ((s64) gas_res_adc << 15) - 16777216) + var1); > + var3 = (((s64) lookupTable2[gas_range] * (s64) var1) >> 9); > + calc_gas_res = (u32) ((var3 + ((s64) var2 >> 1)) / (s64) var2); > + > + return calc_gas_res; > +} > + > +/* Taken from Bosch BME680 API */ > +static u8 bme680_calc_heater_res(struct bme680_data *data, u16 temp) > +{ > + struct bme680_calib *calib = &data->bme680; > + s32 var1, var2, var3, var4, var5, heatr_res_x100; > + u8 heatr_res; > + > + if (temp > 400) /* Cap temperature */ > + temp = 400; > + > + var1 = (((s32) BME680_AMB_TEMP * calib->par_gh3) / 1000) * 256; > + var2 = (calib->par_gh1 + 784) * (((((calib->par_gh2 + 154009) * > + temp * 5) / 100) > + + 3276800) / 10); > + var3 = var1 + (var2 / 2); > + var4 = (var3 / (calib->res_heat_range + 4)); > + var5 = (131 * calib->res_heat_val) + 65536; > + heatr_res_x100 = ((var4 / var5) - 250) * 34; > + heatr_res = (heatr_res_x100 + 50) / 100; > + > + return heatr_res; > +} > + > +/* Taken from Bosch BME680 API */ > +static u8 bme680_calc_heater_dur(u16 dur) > +{ > + u8 durval, factor = 0; > + > + if (dur >= 0xfc0) { > + durval = 0xff; /* Max duration */ > + } else { > + while (dur > 0x3F) { > + dur = dur / 4; > + factor += 1; > + } > + durval = dur + (factor * 64); > + } > + > + return durval; > +} > + > +static int bme680_set_mode(struct bme680_data *data, bool mode) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + > + if (mode) { > + ret = regmap_write_bits(data->regmap, BME680_REG_CTRL_MEAS, > + BME680_MODE_MASK, BME680_MODE_FORCED); > + if (ret < 0) > + dev_err(dev, "failed to set forced mode\n"); > + > + } else { > + ret = regmap_write_bits(data->regmap, BME680_REG_CTRL_MEAS, > + BME680_MODE_MASK, BME680_MODE_SLEEP); > + if (ret < 0) > + dev_err(dev, "failed to set sleep mode\n"); > + > + } > + > + return ret; > +} > + > +static int bme680_chip_config(struct bme680_data *data) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + u8 osrs = BME680_OSRS_HUMID_X(data->oversampling_humid + 1); > + /* > + * Highly recommended to set oversampling of humidity before > + * temperature/pressure oversampling. > + */ > + ret = regmap_update_bits(data->regmap, BME680_REG_CTRL_HUMIDITY, > + BME680_OSRS_HUMIDITY_MASK, osrs); > + if (ret < 0) { > + dev_err(dev, "failed to write ctrl_hum register\n"); > + return ret; > + } > + > + /* IIR filter settings */ > + ret = regmap_update_bits(data->regmap, BME680_REG_CONFIG, > + BME680_FILTER_MASK, > + BME680_FILTER_COEFF); > + if (ret < 0) { > + dev_err(dev, "failed to write config register\n"); > + return ret; > + } > + > + osrs = BME680_OSRS_TEMP_X(data->oversampling_temp + 1) | > + BME680_OSRS_PRESS_X(data->oversampling_press + 1); > + > + ret = regmap_write_bits(data->regmap, BME680_REG_CTRL_MEAS, > + BME680_OSRS_TEMP_MASK | > + BME680_OSRS_PRESS_MASK, > + osrs); > + if (ret < 0) > + dev_err(dev, "failed to write ctrl_meas register\n"); > + > + return ret; > +} > + > +static int bme680_gas_config(struct bme680_data *data) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + u8 heatr_res, heatr_dur; > + > + heatr_res = bme680_calc_heater_res(data, data->heater_temp); > + > + /* set target heater temperature */ > + ret = regmap_write(data->regmap, BME680_REG_RES_HEAT_0, heatr_res); > + if (ret < 0) { > + dev_err(dev, "failed to write res_heat_0 register\n"); > + return ret; > + } > + > + heatr_dur = bme680_calc_heater_dur(data->heater_dur); > + > + /* set target heating duration */ > + ret = regmap_write(data->regmap, BME680_REG_GAS_WAIT_0, heatr_dur); > + if (ret < 0) { > + dev_err(dev, "failted to write gas_wait_0 register\n"); > + return ret; > + } > + > + /* Selecting the runGas and NB conversion settings for the sensor */ > + ret = regmap_update_bits(data->regmap, BME680_REG_CTRL_GAS_1, > + BME680_RUN_GAS_MASK | BME680_NB_CONV_MASK, > + BME680_RUN_GAS_EN | BME680_NB_CONV_0); > + if (ret < 0) > + dev_err(dev, "failed to write ctrl_gas_1 register\n"); > + > + return ret; > +} > + > +/* Outputs temperature measurement in degC */ > +static int bme680_read_temp(struct bme680_data *data, > + int *val, int *val2) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret = 0; > + __be32 tmp = 0; > + s32 adc_temp, comp_temp; > + > + /* set forced mode to trigger measurement */ > + ret = bme680_set_mode(data, true); > + if (ret < 0) > + return ret; > + > + ret = regmap_bulk_read(data->regmap, BME680_REG_TEMP_MSB, > + (u8 *) &tmp, 3); > + if (ret < 0) { > + dev_err(dev, "failed to read temperature\n"); > + return ret; > + } > + > + adc_temp = be32_to_cpu(tmp) >> 12; > + if (adc_temp == BME680_MEAS_SKIPPED) { > + /* reading was skipped */ > + dev_err(dev, "reading temperature skipped\n"); > + return -EINVAL; > + } > + comp_temp = bme680_compensate_temp(data, adc_temp); > + /* > + * val might be NULL if we're called by the read_press/read_humid > + * routine which is callled to get t_fine value used in > + * compensate_press/compensate_humid to get compensated > + * pressure/humidity readings. > + */ > + if (val && val2) { > + *val = comp_temp; > + *val2 = 100; > + return IIO_VAL_FRACTIONAL; > + } > + > + return ret; > +} > + > +/* Outputs pressure measurement in hPa */ > +static int bme680_read_press(struct bme680_data *data, > + int *val, int *val2) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + __be32 tmp = 0; > + s32 adc_press; > + > + /* Read and compensate temperature to get a reading of t_fine */ > + ret = bme680_read_temp(data, NULL, NULL); > + if (ret < 0) > + return ret; > + > + ret = regmap_bulk_read(data->regmap, BME680_REG_PRESS_MSB, > + (u8 *) &tmp, 3); > + if (ret < 0) { > + dev_err(dev, "failed to read pressure\n"); > + return ret; > + } > + > + adc_press = be32_to_cpu(tmp) >> 12; > + if (adc_press == BME680_MEAS_SKIPPED) { > + /* reading was skipped */ > + dev_err(dev, "reading pressure skipped\n"); > + return -EINVAL; > + } > + > + *val = bme680_compensate_press(data, adc_press); > + *val2 = 100; > + return IIO_VAL_FRACTIONAL; > +} > + > +/* Outputs humidity measurement in %r.H */ > +static int bme680_read_humid(struct bme680_data *data, > + int *val, int *val2) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + __be16 tmp = 0; > + s32 adc_humidity; > + u32 comp_humidity; > + > + /* Read and compensate temperature so we get a reading of t_fine */ > + ret = bme680_read_temp(data, NULL, NULL); > + if (ret < 0) > + return ret; > + > + ret = regmap_bulk_read(data->regmap, BM6880_REG_HUMIDITY_MSB, > + (u8 *) &tmp, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read humidity\n"); > + return ret; > + } > + > + adc_humidity = be16_to_cpu(tmp); > + if (adc_humidity == BME680_MEAS_SKIPPED) { > + /* reading was skipped */ > + dev_err(dev, "reading humidity skipped\n"); > + return -EINVAL; > + } > + comp_humidity = bme680_compensate_humid(data, adc_humidity); > + > + *val = comp_humidity; > + *val2 = 1000; > + return IIO_VAL_FRACTIONAL; > +} > + > +/* Outputs gas measurement in ohm */ > +static int bme680_read_gas(struct bme680_data *data, > + int *val) > +{ > + struct device *dev = regmap_get_device(data->regmap); > + int ret; > + __be16 tmp = 0; > + unsigned int check; > + u16 adc_gas_res; > + u8 gas_range; > + > + /* Set heater settings */ > + ret = bme680_gas_config(data); > + if (ret < 0) { > + dev_err(dev, "failed to set gas config\n"); > + return ret; > + } > + > + /* set forced mode to trigger a single measurement */ > + ret = bme680_set_mode(data, true); > + if (ret < 0) > + return ret; > + > + ret = regmap_read(data->regmap, BME680_REG_MEAS_STAT_0, &check); > + if (check & BME680_GAS_MEAS_BIT) { > + dev_err(dev, "gas measurement incomplete\n"); > + return -EBUSY; > + } > + > + ret = regmap_read(data->regmap, BME680_REG_GAS_R_LSB, &check); > + if (ret < 0) { > + dev_err(dev, "failed to read gas_r_lsb register\n"); > + return ret; > + } > + > + if ((check & BME680_GAS_STAB_BIT) == 0) { > + /* > + * occurs if either the gas heating duration was insuffient > + * to reach the target heater temperature or the target > + * heater temperature was too high for the heater sink to > + * reach. > + */ > + dev_err(dev, "heater failed to reach the target temperature\n"); > + return -EINVAL; > + } > + > + ret = regmap_bulk_read(data->regmap, BME680_REG_GAS_MSB, > + (u8 *) &tmp, 2); > + if (ret < 0) { > + dev_err(dev, "failed to read gas resistance\n"); > + return ret; > + } > + > + gas_range = check & BME680_GAS_RANGE_MASK; > + adc_gas_res = be16_to_cpu(tmp) >> BME680_ADC_GAS_RES_SHIFT; > + > + *val = bme680_compensate_gas(data, adc_gas_res, gas_range); > + return IIO_VAL_INT; > +} > + > +static int bme680_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + struct bme680_data *data = iio_priv(indio_dev); > + > + switch (mask) { > + case IIO_CHAN_INFO_PROCESSED: > + switch (chan->type) { > + case IIO_TEMP: > + return bme680_read_temp(data, val, val2); > + case IIO_PRESSURE: > + return bme680_read_press(data, val, val2); > + case IIO_HUMIDITYRELATIVE: > + return bme680_read_humid(data, val, val2); > + case IIO_RESISTANCE: > + return bme680_read_gas(data, val); > + default: > + return -EINVAL; > + } > + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: > + switch (chan->type) { > + case IIO_TEMP: > + *val = 1 << data->oversampling_temp; > + return IIO_VAL_INT; > + case IIO_PRESSURE: > + *val = 1 << data->oversampling_press; > + return IIO_VAL_INT; > + case IIO_HUMIDITYRELATIVE: > + *val = 1 << data->oversampling_humid; > + return IIO_VAL_INT; > + default: > + return -EINVAL; > + } > + default: > + return -EINVAL; > + } > + > + return -EINVAL; > +} > + > +static int bme680_write_oversampling_ratio_temp(struct bme680_data *data, > + int val) > +{ > + int i; > + > + for (i = 0; i < ARRAY_SIZE(bme680_oversampling_avail); ++i) { > + if (bme680_oversampling_avail[i] == val) { > + data->oversampling_temp = ilog2(val); > + > + return bme680_chip_config(data); > + } > + } > + > + return -EINVAL; > +} > + > +static int bme680_write_oversampling_ratio_press(struct bme680_data *data, > + int val) > +{ > + int i; > + > + for (i = 0; i < ARRAY_SIZE(bme680_oversampling_avail); ++i) { > + if (bme680_oversampling_avail[i] == val) { > + data->oversampling_press = ilog2(val); > + > + return bme680_chip_config(data); > + } > + } > + > + return -EINVAL; > +} > + > +static int bme680_write_oversampling_ratio_humid(struct bme680_data *data, > + int val) > +{ > + int i; > + > + for (i = 0; i < ARRAY_SIZE(bme680_oversampling_avail); ++i) { > + if (bme680_oversampling_avail[i] == val) { > + data->oversampling_humid = ilog2(val); > + > + return bme680_chip_config(data); > + } > + } > + > + return -EINVAL; > +} > + > +static int bme680_write_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int val, int val2, long mask) > +{ > + struct bme680_data *data = iio_priv(indio_dev); > + > + switch (mask) { > + case IIO_CHAN_INFO_OVERSAMPLING_RATIO: > + switch (chan->type) { > + case IIO_TEMP: > + return bme680_write_oversampling_ratio_temp(data, val); > + case IIO_PRESSURE: > + return bme680_write_oversampling_ratio_press(data, val); > + case IIO_HUMIDITYRELATIVE: > + return bme680_write_oversampling_ratio_humid(data, val); > + default: > + return -EINVAL; > + } > + default: > + return -EINVAL; > + } > + > + return -EINVAL; > +} > + > +static const char bme680_oversampling_ratio_show[] = "1 2 4 8 16"; > + > +static IIO_CONST_ATTR(oversampling_ratio_available, > + bme680_oversampling_ratio_show); > + > +static struct attribute *bme680_attributes[] = { > + &iio_const_attr_oversampling_ratio_available.dev_attr.attr, > + NULL, > +}; > + > +static const struct attribute_group bme680_attribute_group = { > + .attrs = bme680_attributes, > +}; > + > +static const struct iio_info bme680_info = { > + .read_raw = &bme680_read_raw, > + .write_raw = &bme680_write_raw, > + .attrs = &bme680_attribute_group, > +}; > + > +static const char *bme680_match_acpi_device(struct device *dev) > +{ > + const struct acpi_device_id *id; > + > + id = acpi_match_device(dev->driver->acpi_match_table, dev); > + if (!id) > + return NULL; > + > + return dev_name(dev); > +} > + > +static void bme680_core_remove(void *arg) > +{ > + iio_device_unregister(arg); > +} > + > +int bme680_core_probe(struct device *dev, struct regmap *regmap, > + const char *name) > +{ > + struct iio_dev *indio_dev; > + struct bme680_data *data; > + int ret; > + > + indio_dev = devm_iio_device_alloc(dev, sizeof(*data)); > + if (!indio_dev) > + return -ENOMEM; > + > + ret = devm_add_action(dev, bme680_core_remove, indio_dev); > + if (ret < 0) { > + dev_err(dev, "failed to register remove action\n"); > + return ret; > + } > + > + if (!name && ACPI_HANDLE(dev)) > + name = bme680_match_acpi_device(dev); > + > + data = iio_priv(indio_dev); > + dev_set_drvdata(dev, indio_dev); > + data->regmap = regmap; > + indio_dev->dev.parent = dev; > + indio_dev->name = name; > + indio_dev->channels = bme680_channels; > + indio_dev->num_channels = ARRAY_SIZE(bme680_channels); > + indio_dev->info = &bme680_info; > + indio_dev->modes = INDIO_DIRECT_MODE; > + > + /* default values for the sensor */ > + data->oversampling_humid = ilog2(2); /* 2X oversampling rate */ > + data->oversampling_press = ilog2(4); /* 4X oversampling rate */ > + data->oversampling_temp = ilog2(8); /* 8X oversampling rate */ > + data->heater_temp = 320; /* degree Celsius */ > + data->heater_dur = 150; /* milliseconds */ > + > + ret = bme680_chip_config(data); > + if (ret < 0) { > + dev_err(dev, "failed to set chip_config data\n"); > + return ret; > + } > + > + ret = bme680_gas_config(data); > + if (ret < 0) { > + dev_err(dev, "failed to set gas config data\n"); > + return ret; > + } > + > + ret = bme680_read_calib(data, &data->bme680); > + if (ret < 0) { > + dev_err(dev, > + "failed to read calibration coefficients at probe\n"); > + return ret; > + } > + > + return iio_device_register(indio_dev); > +} > +EXPORT_SYMBOL_GPL(bme680_core_probe); > + > +MODULE_AUTHOR("Himanshu Jha <himanshujha199640@xxxxxxxxx>"); > +MODULE_DESCRIPTION("Bosch BME680 Driver"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/iio/chemical/bme680_i2c.c b/drivers/iio/chemical/bme680_i2c.c > new file mode 100644 > index 0000000..a3a77cf > --- /dev/null > +++ b/drivers/iio/chemical/bme680_i2c.c > @@ -0,0 +1,83 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * BME680 - I2C Driver > + * > + * Copyright (C) 2018 Himanshu Jha <himanshujha199640@xxxxxxxxx> > + * > + * 7-Bit I2C slave address is: > + * - 0x76 if SDO is pulled to GND > + * - 0x77 if SDO is pulled to VDDIO > + * > + * Note: SDO pin cannot be left floating otherwise I2C address > + * will be undefined. > + */ > +#include <linux/acpi.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > + > +#include "bme680.h" > + > +static int bme680_i2c_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct regmap *regmap; > + const char *name = NULL; > + unsigned int val; > + int ret; > + > + regmap = devm_regmap_init_i2c(client, &bme680_regmap_config); > + if (IS_ERR(regmap)) { > + dev_err(&client->dev, "Failed to register i2c regmap %d\n", > + (int)PTR_ERR(regmap)); > + return PTR_ERR(regmap); > + } > + > + ret = regmap_write(regmap, BME680_REG_SOFT_RESET, > + BME680_CMD_SOFTRESET); > + if (ret < 0) > + return ret; > + > + ret = regmap_read(regmap, BME680_REG_CHIP_I2C_ID, &val); > + if (ret < 0) { > + dev_err(&client->dev, "Error reading I2C chip ID\n"); > + return ret; > + } > + > + if (val != BME680_CHIP_ID_VAL) { > + dev_err(&client->dev, "Wrong chip ID, got %x expected %x\n", > + val, BME680_CHIP_ID_VAL); > + return -ENODEV; > + } > + > + if (id) > + name = id->name; > + > + return bme680_core_probe(&client->dev, regmap, name); > +} > + > +static const struct i2c_device_id bme680_i2c_id[] = { > + {"bme680", 0}, > + {}, > +}; > +MODULE_DEVICE_TABLE(i2c, bme680_i2c_id); > + > +static const struct acpi_device_id bme680_acpi_match[] = { > + {"BME0680", 0}, > + {}, > +}; > +MODULE_DEVICE_TABLE(acpi, bme680_acpi_match); > + > +static struct i2c_driver bme680_i2c_driver = { > + .driver = { > + .name = "bme680_i2c", > + .acpi_match_table = ACPI_PTR(bme680_acpi_match), > + }, > + .probe = bme680_i2c_probe, > + .id_table = bme680_i2c_id, > +}; > +module_i2c_driver(bme680_i2c_driver); > + > +MODULE_AUTHOR("Himanshu Jha <himanshujha199640@xxxxxxxxx>"); > +MODULE_DESCRIPTION("BME680 I2C driver"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/iio/chemical/bme680_spi.c b/drivers/iio/chemical/bme680_spi.c > new file mode 100644 > index 0000000..1fb3466 > --- /dev/null > +++ b/drivers/iio/chemical/bme680_spi.c > @@ -0,0 +1,123 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * BME680 - SPI Driver > + * > + * Copyright (C) 2018 Himanshu Jha <himanshujha199640@xxxxxxxxx> > + */ > +#include <linux/acpi.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/spi/spi.h> > + > +#include "bme680.h" > + > +static int bme680_regmap_spi_write(void *context, const void *data, > + size_t count) > +{ > + struct spi_device *spi = context; > + u8 buf[2]; > + > + memcpy(buf, data, 2); > + /* > + * The SPI register address (= full register address without bit 7) > + * and the write command (bit7 = RW = '0') > + */ > + buf[0] &= ~0x80; > + > + return spi_write_then_read(spi, buf, 2, NULL, 0); > +} > + > +static int bme680_regmap_spi_read(void *context, const void *reg, > + size_t reg_size, void *val, size_t val_size) > +{ > + struct spi_device *spi = context; > + > + return spi_write_then_read(spi, reg, reg_size, val, val_size); > +} > + > +static struct regmap_bus bme680_regmap_bus = { > + .write = bme680_regmap_spi_write, > + .read = bme680_regmap_spi_read, > + .reg_format_endian_default = REGMAP_ENDIAN_BIG, > + .val_format_endian_default = REGMAP_ENDIAN_BIG, > +}; > + > +static int bme680_spi_probe(struct spi_device *spi) > +{ > + const struct spi_device_id *id = spi_get_device_id(spi); > + struct regmap *regmap; > + unsigned int val; > + int ret; > + > + spi->bits_per_word = 8; > + ret = spi_setup(spi); > + if (ret < 0) { > + dev_err(&spi->dev, "spi_setup failed!\n"); > + return ret; > + } > + > + regmap = devm_regmap_init(&spi->dev, &bme680_regmap_bus, > + &spi->dev, &bme680_regmap_config); > + if (IS_ERR(regmap)) { > + dev_err(&spi->dev, "Failed to register spi regmap %d\n", > + (int)PTR_ERR(regmap)); > + return PTR_ERR(regmap); > + } > + > + ret = regmap_write(regmap, BME680_REG_SOFT_RESET, > + BME680_CMD_SOFTRESET); > + if (ret < 0) > + return ret; > + > + /* after power-on reset, Page 0(0x80-0xFF) of spi_mem_page is active */ > + ret = regmap_read(regmap, BME680_REG_CHIP_SPI_ID, &val); > + if (ret < 0) { > + dev_err(&spi->dev, "Error reading SPI chip ID\n"); > + return ret; > + } > + > + if (val != BME680_CHIP_ID_VAL) { > + dev_err(&spi->dev, "Wrong chip ID, got %x expected %x\n", > + val, BME680_CHIP_ID_VAL); > + return -ENODEV; > + } > + /* > + * select Page 1 of spi_mem_page to enable access to > + * to registers from address 0x00 to 0x7F. > + */ > + ret = regmap_write_bits(regmap, BME680_REG_STATUS, > + BME680_SPI_MEM_PAGE_BIT, > + BME680_SPI_MEM_PAGE_1_VAL); > + if (ret < 0) { > + dev_err(&spi->dev, "failed to set page 1 of spi_mem_page\n"); > + return ret; > + } > + > + return bme680_core_probe(&spi->dev, regmap, id->name); > +} > + > +static const struct spi_device_id bme680_spi_id[] = { > + {"bme680", 0}, > + {}, > +}; > +MODULE_DEVICE_TABLE(spi, bme680_spi_id); > + > +static const struct acpi_device_id bme680_acpi_match[] = { > + {"BME0680", 0}, > + {}, > +}; > +MODULE_DEVICE_TABLE(acpi, bme680_acpi_match); > + > +static struct spi_driver bme680_spi_driver = { > + .driver = { > + .name = "bme680_spi", > + .acpi_match_table = ACPI_PTR(bme680_acpi_match), > + }, > + .probe = bme680_spi_probe, > + .id_table = bme680_spi_id, > +}; > +module_spi_driver(bme680_spi_driver); > + > +MODULE_AUTHOR("Himanshu Jha <himanshujha199640@xxxxxxxxx>"); > +MODULE_DESCRIPTION("Bosch BME680 SPI driver"); > +MODULE_LICENSE("GPL v2"); > -- > 2.7.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html