> On Wed, 21 Jun 2017 21:21:28 +0200
> Lorenzo Bianconi <lorenzo.bianconi83@xxxxxxxxx> wrote:
>
>> Add open drain support in order to share requested IRQ line between
>> st_lsm6dsx device and other peripherals
>>
>> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@xxxxxx>
> Issue when IRQF_RISING and open drain is set.
>
Hi Jonathan,
> Otherwise looks good.
>> ---
>> drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c | 17 +++++++++++++++++
>> 1 file changed, 17 insertions(+)
>>
>> diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
>> index 2a72acc6e049..e2737dc71b67 100644
>> --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
>> +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
>> @@ -31,6 +31,8 @@
>> #include <linux/iio/iio.h>
>> #include <linux/iio/buffer.h>
>>
>> +#include <linux/platform_data/st_sensors_pdata.h>
>> +
>> #include "st_lsm6dsx.h"
>>
>> #define ST_LSM6DSX_REG_FIFO_THL_ADDR 0x06
>> @@ -39,6 +41,8 @@
>> #define ST_LSM6DSX_REG_FIFO_DEC_GXL_ADDR 0x08
>> #define ST_LSM6DSX_REG_HLACTIVE_ADDR 0x12
>> #define ST_LSM6DSX_REG_HLACTIVE_MASK BIT(5)
>> +#define ST_LSM6DSX_REG_PP_OD_ADDR 0x12
>> +#define ST_LSM6DSX_REG_PP_OD_MASK BIT(4)
>> #define ST_LSM6DSX_REG_FIFO_MODE_ADDR 0x0a
>> #define ST_LSM6DSX_FIFO_MODE_MASK GENMASK(2, 0)
>> #define ST_LSM6DSX_FIFO_ODR_MASK GENMASK(6, 3)
>> @@ -417,6 +421,8 @@ static const struct iio_buffer_setup_ops st_lsm6dsx_buffer_ops = {
>>
>> int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
>> {
>> + struct device_node *np = hw->dev->of_node;
>> + struct st_sensors_platform_data *pdata;
>> struct iio_buffer *buffer;
>> unsigned long irq_type;
>> bool irq_active_low;
>> @@ -444,6 +450,17 @@ int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
>> if (err < 0)
>> return err;
>>
>> + pdata = (struct st_sensors_platform_data *)hw->dev->platform_data;
>> + if ((np && of_property_read_bool(np, "drive-open-drain")) ||
>> + (pdata && pdata->open_drain)) {
>> + err = st_lsm6dsx_write_with_mask(hw, ST_LSM6DSX_REG_PP_OD_ADDR,
>> + ST_LSM6DSX_REG_PP_OD_MASK, 1);
>> + if (err < 0)
>> + return err;
>> +
>> + irq_type |= IRQF_SHARED;
>> + }
>> +
> In common with the mpu3050 which was the first driver in IIO to do open drain,
> I think you need to think about precedence as we allow for IRQF_RISING
> and IRQF_FALLING already. Open drain only allows for shared interrupts
> if IRQF_FALLING (I think)
>> err = devm_request_threaded_irq(hw->dev, hw->irq,
>> st_lsm6dsx_handler_irq,
>> st_lsm6dsx_handler_thread,
>
I have not got the difference between IRQF_RISING and IRQF_FALLING
when the irq line
is marked as shared (when open drain is enabled).
Looking at the code, mpu3050 gyro sensor does not support shared interrupts
with IRQF_RISING and IRQF_TRIGGER_HIGH. Is it a hw limitation?
Speaking with digital designer, lsm6dsx series allows open drain mode
even if the requested irq line
is IRQF_TRIGGER_HIGH or IRQF_RISING, we need to add a pull-down resistor.
Moreover ST framework already supports open drain if the requested
interrupt is IRQF_RISING.
Regards,
Lorenzo
--
UNIX is Sexy: who | grep -i blonde | talk; cd ~; wine; talk; touch;
unzip; touch; strip; gasp; finger; gasp; mount; fsck; more; yes; gasp;
umount; make clean; sleep
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
