On 2017-04-24 22:05, Andy Shevchenko wrote:
> On Mon, 2017-04-24 at 21:28 +0200, Jan Kiszka wrote:
>> This is an upstream port of an IIO driver for the TI ADC108S102 and
>> ADC128S102. The former can be found on the Intel Galileo Gen2 and the
>> Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
>> included.
>>
>> Original author: Bogdan Pricop <bogdan.pricop@xxxxxxxxxx>
>> Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
>> Todor Minchev <todor@xxxxxxxxxxxxx>.
>
>> +#include <linux/interrupt.h>
>> +#include <linux/module.h>
>> +#include <linux/spi/spi.h>
>> +
>> +#include <linux/platform_data/adc1x8s102.h>
>> +#include <linux/regulator/consumer.h>
>> +
>> +#include <linux/delay.h>
>> +#include <linux/acpi.h>
>> +#include <linux/property.h>
>> +#include <linux/gpio.h>
>> +
>> +#include <linux/spi/pxa2xx_spi.h>
>
> Perhaps alphabetical order?
>
>> +
>> +/* 16-bit SPI command format:
>> + * [15:14] Ignored
>> + * [13:11] 3-bit channel address
>> + * [10:0] Ignored
>> + */
>> +#define ADC1x8S102_CMD(ch) (((ch) << (8)) << (3))
>
> I guess ((u16)(ch) << 11) would be slightly better.
>
>> +
>> +/*
>> + * 16-bit SPI response format:
>> + * [15:12] Zeros
>> + * [11:0] 12-bit ADC sample (for ADC108S102, [1:0] will always be
>> 0).
>> + */
>
>> +#define ADC1x8S102_RES_DATA(res) (res & ((1 <<
>> ADC1x8S102_BITS) - 1))
>
> GENMASK() and to align with above
>
> ((u16)(res) & GENMASK(11, 0))
>
>> + /* SPI message buffers:
>> + * tx_buf: |C0|C1|C2|C3|C4|C5|C6|C7|XX|
>> + * rx_buf: |XX|R0|R1|R2|R3|R4|R5|R6|R7|tt|tt|tt|tt|
>> + *
>> + * tx_buf: 8 channel read commands, plus 1 dummy command
>> + * rx_buf: 1 dummy response, 8 channel responses, plus 64-
>> bit timestamp
>> + */
>> + __be16 rx_buf[13]
>> ____cacheline_aligned;
>> + __be16 tx_buf[9];
>
> Would it be better to have tx_buf with ____cache_aligned? (IIUC it's
> already by fact of above, though...)
>
>> +};
>
>> tatic int adc1x8s102_update_scan_mode(struct iio_dev *indio_dev,
>> + unsigned long const *active_scan_mask)
>> +{
>> + struct adc1x8s102_state *st;
>> + int i, j;
>> +
>> + st = iio_priv(indio_dev);
>> +
>
>> + /* Fill in the first x shorts of tx_buf with the number of
>> channels
>> + * enabled for sampling by the triggered buffer
>> + */
>
> /*
> * Is it okay style for
> * multi-line comments?
> */
>
>> + for (i = 0, j = 0; i < ADC1x8S102_MAX_CHANNELS; i++) {
>> + if (test_bit(i, active_scan_mask)) {
>
> for_each_set_bit()
>
>> + st->tx_buf[j] =
>> cpu_to_be16(ADC1x8S102_CMD(i));
>> + j++;
>> + }
>> + }
>> + /* One dummy command added, to clock in the last response */
>> + st->tx_buf[j] = 0x00;
>
>> +}
>> +
>
>> +static int adc1x8s102_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>
>> + int *val,
>> + int *val2,
>> + long m)
>
> One line?
>
>> +{
>> + int ret;
>> + struct adc1x8s102_state *st;
>> +
>> + st = iio_priv(indio_dev);
>> +
>> + switch (m) {
>> + case IIO_CHAN_INFO_RAW:
>> + mutex_lock(&indio_dev->mlock);
>> + if (indio_dev->currentmode == INDIO_BUFFER_TRIGGERED)
>> {
>> + ret = -EBUSY;
>
>> + dev_warn(&st->spi->dev,
>> + "indio_dev->currentmode is
>> INDIO_BUFFER_TRIGGERED\n");
>
> Indentation?
>
All valid remarks, will address.
>> + } else {
>> + ret = adc1x8s102_scan_direct(st, chan-
>>> address);
>> + }
>> + mutex_unlock(&indio_dev->mlock);
>> +
>> + if (ret < 0)
>> + return ret;
>> + *val = ADC1x8S102_RES_DATA(ret);
>> +
>> + return IIO_VAL_INT;
>> + case IIO_CHAN_INFO_SCALE:
>> + switch (chan->type) {
>> + case IIO_VOLTAGE:
>> + if (st->reg)
>> + *val = regulator_get_voltage(st->reg)
>> / 1000;
>> + else
>> + *val = st->ext_vin;
>> +
>> + *val2 = chan->scan_type.realbits;
>> + return IIO_VAL_FRACTIONAL_LOG2;
>> + default:
>> + dev_warn(&st->spi->dev,
>> + "Invalid channel type %u for channel
>> %d\n",
>> + chan->type, chan->channel);
>> + return -EINVAL;
>> + }
>> + default:
>> + dev_warn(&st->spi->dev, "Invalid IIO_CHAN_INFO:
>> %lu\n", m);
>> + return -EINVAL;
>> + }
>> +}
>
>> +#ifdef CONFIG_ACPI
>> +typedef int (*acpi_setup_handler)(struct spi_device *,
>> + const struct
>> adc1x8s102_platform_data **);
>> +
>> +static const struct adc1x8s102_platform_data int3495_platform_data =
>> {
>> + .ext_vin = 5000, /* 5 V */
>> +};
>> +
>
>> +/* Galileo Gen 2 SPI setup */
>> +static int
>> +adc1x8s102_setup_int3495(struct spi_device *spi,
>> + const struct adc1x8s102_platform_data
>> **pdata)
>> +{
>
>> + struct pxa2xx_spi_chip *chip_data;
>
> This one is too big to waste memory on one member.
>
>> +
>> + chip_data = devm_kzalloc(&spi->dev, sizeof(*chip_data),
>> GFP_KERNEL);
>> + if (!chip_data)
>> + return -ENOMEM;
>> +
>> + chip_data->gpio_cs = ADC1x8S102_GALILEO2_CS;
>> + spi->controller_data = chip_data;
>> + dev_info(&spi->dev, "setting GPIO CS value to %d\n",
>> + chip_data->gpio_cs);
>> + spi_setup(spi);
>> +
>> + *pdata = &int3495_platform_data;
>> +
>> + return 0;
>> +}
>
> This is weird approach.
Let me dig deeper if are allowed to pass a static struct here as well.
But the struct is driver-defined.
> Moreover, please do not use platform data at all.
That is just following pre-existing pattern, just look around in the
iio/adc folder, not to speak of others. But I'm open to learn about any
newer pattern there is.
>
>> +
>> +static const struct acpi_device_id adc1x8s102_acpi_ids[] = {
>> + { "INT3495", (kernel_ulong_t)&adc1x8s102_setup_int3495 },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(acpi, adc1x8s102_acpi_ids);
>> +#endif
>> +
>> +static int adc1x8s102_probe(struct spi_device *spi)
>> +{
>> + const struct adc1x8s102_platform_data *pdata = spi-
>>> dev.platform_data;
>> + struct adc1x8s102_state *st;
>> + struct iio_dev *indio_dev;
>> + int ret;
>> +
>
>> +#ifdef CONFIG_ACPI
>
> No.
...because?
>
>> + if (ACPI_COMPANION(&spi->dev)) {
>> + acpi_setup_handler setup_handler;
>> + const struct acpi_device_id *id;
>> +
>> + id = acpi_match_device(adc1x8s102_acpi_ids, &spi-
>>> dev);
>> + if (!id)
>> + return -ENODEV;
>> +
>
>> + setup_handler = (acpi_setup_handler)id->driver_data;
>> + if (setup_handler) {
>> + ret = setup_handler(spi, &pdata);
>> + if (ret)
>> + return ret;
>> + }
>
> No way.
Constructive feedback, please.
>
>> + }
>> +#endif
>> +
>> + if (!pdata) {
>> + dev_err(&spi->dev, "Cannot get adc1x8s102 platform
>> data\n");
>> + return -ENODEV;
>> + }
>> +
>
>> +error_cleanup_ring:
>> + iio_triggered_buffer_cleanup(indio_dev);
>> +error_disable_reg:
>> + regulator_disable(st->reg);
>
> Does devm_() help to get rid of these?
Yep. See also other drivers.
>
>> +
>> + return ret;
>> +}
>
>> +
>> +static int adc1x8s102_remove(struct spi_device *spi)
>> +{
>> + struct iio_dev *indio_dev = spi_get_drvdata(spi);
>> + struct adc1x8s102_state *st = iio_priv(indio_dev);
>> +
>
>> + iio_device_unregister(indio_dev);
>> + iio_triggered_buffer_cleanup(indio_dev);
>> +
>> + regulator_disable(st->reg);
>
> Ditto.
>
>> +
>> + return 0;
>> +}
>> +
>
>> +++ b/include/linux/platform_data/adc1x8s102.h
>
> It must be no such file at all!
> Please, remove it completely.
Not without explaining what the new style is. As I said, the existing
driver use that as well. The fact that there is no OF binding yet
exploiting this should be no excuse IMHO.
Jan
--
Siemens AG, Corporate Technology, CT RDA ITP SES-DE
Corporate Competence Center Embedded Linux
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
