2017-01-18 12:37 GMT+01:00 Thierry Reding <thierry.reding@xxxxxxxxx>:
> On Wed, Jan 18, 2017 at 12:15:58PM +0100, Benjamin Gaignard wrote:
>> 2017-01-18 11:08 GMT+01:00 Thierry Reding <thierry.reding@xxxxxxxxx>:
>> > On Thu, Jan 05, 2017 at 10:25:40AM +0100, Benjamin Gaignard wrote:
> [...]
>> >> +static u32 active_channels(struct stm32_pwm *dev)
>> >> +{
>> >> + u32 ccer;
>> >> +
>> >> + regmap_read(dev->regmap, TIM_CCER, &ccer);
>> >> +
>> >> + return ccer & TIM_CCER_CCXE;
>> >> +}
>> >
>> > This looks like something that you could track in software, but this is
>> > probably fine, too. Again, technically regmap_read() could fail, so you
>> > might want to consider adding some code to handle it. In practice it
>> > probably won't, so maybe you don't.
>>
>> TIM_CCER_CCXE is a value that IIO timer can also read (not write) so
>> I have keep the same logic for pwm driver.
>
> Would that not be racy? What happens if after active_channels() here,
> the IIO timer modifies the TIM_CCER register?
IIO timer only read this register not write it so no racy condition here
>
>> >> + ret = stm32_pwm_config(chip, pwm, state->duty_cycle, state->period);
>> >> + if (ret)
>> >> + return ret;
>> >> +
>> >> + if (!enabled && state->enabled)
>> >> + ret = stm32_pwm_enable(chip, pwm);
>> >> +
>> >> + return ret;
>> >> +}
>> >
>> > Would it be possible to merge stm32_pwm_disable(), stm32_pwm_enable(),
>> > stm32_pwm_set_polarity() and stm32_pwm_config() into stm32_pwm_apply()?
>> > Part of the reason for the atomic API was to make it easier to write
>> > these drivers, but your implementation effectively copies what the
>> > transitional helpers do.
>> >
>> > It might not make a difference technically in your case, but I think
>> > it'd make the implementation more compact and set a better example for
>> > future reference.
>>
>> hmm... it will create a fat function with lot of where
>> enabling/disabling/configuration
>> will be mixed I'm really not convince that will more compact and readable.
>
> I don't object to splitting this up into separate functions, I just
> don't think the functions should correspond to the legacy ones. One
> variant that I think could work out nicely would be to have one
> function that precomputes the various values, call in from ->apply()
> and then do only the register writes along with a couple of
> conditionals depending on enable state, for example.
Ok I will change functions prototype so they will not be like legacy ones
but I will keep the current split.
>
>> >> +static const struct pwm_ops stm32pwm_ops = {
>> >> + .owner = THIS_MODULE,
>> >> + .apply = stm32_pwm_apply,
>> >> +};
>> >> +
>> >> +static int stm32_pwm_set_breakinput(struct stm32_pwm *priv,
>> >> + int level, int filter)
>> >> +{
>> >> + u32 bdtr = TIM_BDTR_BKE;
>> >> +
>> >> + if (level)
>> >> + bdtr |= TIM_BDTR_BKP;
>> >> +
>> >> + bdtr |= (filter & TIM_BDTR_BKF_MASK) << TIM_BDTR_BKF_SHIFT;
>> >> +
>> >> + regmap_update_bits(priv->regmap,
>> >> + TIM_BDTR, TIM_BDTR_BKE | TIM_BDTR_BKP | TIM_BDTR_BKF,
>> >> + bdtr);
>> >> +
>> >> + regmap_read(priv->regmap, TIM_BDTR, &bdtr);
>> >> +
>> >> + return (bdtr & TIM_BDTR_BKE) ? 0 : -EINVAL;
>> >> +}
>> >> +
>> >> +static int stm32_pwm_set_breakinput2(struct stm32_pwm *priv,
>> >> + int level, int filter)
>> >> +{
>> >> + u32 bdtr = TIM_BDTR_BK2E;
>> >> +
>> >> + if (level)
>> >> + bdtr |= TIM_BDTR_BK2P;
>> >> +
>> >> + bdtr |= (filter & TIM_BDTR_BKF_MASK) << TIM_BDTR_BK2F_SHIFT;
>> >> +
>> >> + regmap_update_bits(priv->regmap,
>> >> + TIM_BDTR, TIM_BDTR_BK2E |
>> >> + TIM_BDTR_BK2P |
>> >> + TIM_BDTR_BK2F,
>> >> + bdtr);
>> >> +
>> >> + regmap_read(priv->regmap, TIM_BDTR, &bdtr);
>> >> +
>> >> + return (bdtr & TIM_BDTR_BK2E) ? 0 : -EINVAL;
>> >> +}
>> >
>> > As far as I can tell the only difference here is the various bit
>> > positions. Can you collapse the above two functions and add a new
>> > parameter to unify some code?
>>
>> Yes it is all about bit shifting, I had try unify those two functions
>> with index has additional parameter
>> but it just add if() before each lines so no real benefit for code size.
>
> How about if you precompute the values and masks? Something like:
>
> u32 bke = (index == 0) ? ... : ...;
> u32 bkp = (index == 0) ? ... : ...;
> u32 bkf = (index == 0) ? ... : ...;
> u32 mask = (index == 0) ? ... : ...;
>
> bdtr = bke | bkf;
>
> if (level)
> bdtr |= bkp;
>
> regmap_update_bits(priv->regmap, TIM_BDTR, mask, bdtr);
>
> regmap_read(priv->regmap, TIM_BDTR, &bdtr);
>
> return (bdtr & bke) ? 0 : -EINVAL;
>
> ?
ok done
--
Benjamin Gaignard
Graphic Study Group
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
