On 30/11/16 08:17, Peter Rosin wrote:
> Analog Devices ADG792A/G is a triple 4:1 mux.
>
> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx>
Few comments inline. Worth adding anything about the gpio (output pins) to
the binding at this stage as well? Would certainly be nice to support
them.
Jonathan
> ---
> .../devicetree/bindings/misc/mux-adg792a.txt | 64 ++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/misc/mux-adg792a.txt
>
> diff --git a/Documentation/devicetree/bindings/misc/mux-adg792a.txt b/Documentation/devicetree/bindings/misc/mux-adg792a.txt
> new file mode 100644
> index 000000000000..4677f9ab1c55
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/mux-adg792a.txt
> @@ -0,0 +1,64 @@
> +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers
> +
> +Required properties:
> +- compatible : "adi,adg792a" or "adi,adg792g"
> +- #mux-control-cells : <0> if parallel, or <1> if not.
> +* Standard mux-controller bindings as decribed in mux-controller.txt
> +
> +Optional properties:
> +- adi,parallel : if present, the three muxes are bound together with a single
> + mux controller, controlling all three muxes in parallel.
> +- adi,idle-state : if present, array of states the three mux controllers will
> + have when idle (or, if parallel, a single idle-state).
Hmm. These are actually a policy decision. As only one policy will make
sense for a given set of hardware probably fine to have it in here I guess.
Might be worth adding a note to say this though.
> +
> +Mux controller states 0 through 3 correspond to signals A through D in the
> +datasheet. Mux controller states 4 and 5 are only available as possible idle
> +states. State 4 represents that nothing is connected, and state 5 represents
> +that the mux controller keeps the mux in its previously selected state during
> +the idle period. State 5 is the default idle state.
I'm never a great fan of magic numbers. Can we represent this more cleanly by
breaking it into multiple properties?
Optional:
adi,idle-switch-to-channel : switch to this channel when idle.
adi,idle-high-impedance : <boolean> the nothing connected state?
If neither present leaves it in previous state?
> +
> +Example:
> +
> + /* three independent mux controllers (of which one is used) */
> + &i2c0 {
> + mux: adg792a@50 {
> + compatible = "adi,adg792a";
> + reg = <0x50>;
> + #mux-control-cells = <1>;
> + };
> + };
> +
> + adc-mux {
> + compatible = "iio-mux";
> + io-channels = <&adc 0>;
> + io-channel-names = "parent";
> +
> + mux-controls = <&mux 1>;
> +
> + channels = "sync-1", "", "out";
> + };
> +
> +
> + /*
> + * Three parallel muxes with one mux controller, useful e.g. if
> + * the adc is differential, thus needing two signals to be muxed
> + * simultaneously for correct operation.
> + */
> + &i2c0 {
> + pmux: adg792a@50 {
> + compatible = "adi,adg792a";
> + reg = <0x50>;
> + #mux-control-cells = <0>;
> + adi,parallel;
> + };
> + };
> +
> + diff-adc-mux {
> + compatible = "iio-mux";
> + io-channels = <&adc 0>;
> + io-channel-names = "parent";
> +
> + mux-controls = <&pmux>;
> +
> + channels = "sync-1", "", "out";
> + };
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
