Hello Matt,
thank you for your suggestions. See below.
Matt Ranostay <matt.ranostay@xxxxxxxxxxxx> schrieb am Sat, 17. Dec 00:53:
> On Tue, Dec 13, 2016 at 10:02 AM, Andreas Klinger <ak@xxxxxxxxxxxxx> wrote:
> > This is the IIO driver for AVIA HX711 ADC which ist mostly used in weighting
> > cells.
>
> First off cool that this is finally getting a driver... I'll have to
> get the SparkFun breakout and really cheap scale to test :).
>
> >
> > The protocol is quite simple and using GPIO's:
> > One GPIO is used as clock (SCK) while another GPIO is read (DOUT)
> >
> > Signed-off-by: Andreas Klinger <ak@xxxxxxxxxxxxx>
> > ---
> > drivers/iio/adc/Kconfig | 13 +++
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/hx711.c | 269 +++++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 283 insertions(+)
> > create mode 100644 drivers/iio/adc/hx711.c
> >
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 932de1f9d1e7..7902b50fcf32 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -205,6 +205,19 @@ config HI8435
> > This driver can also be built as a module. If so, the module will be
> > called hi8435.
> >
> > +config HX711
> > + tristate "AVIA HX711 ADC for weight cells"
> > + depends on GPIOLIB
> > + help
> > + If you say yes here you get support for AVIA HX711 ADC which is used
> > + for weight cells
> > +
> > + This driver uses two GPIO's, one for setting the clock and the other
> > + one for getting the data
> > +
> > + This driver can also be built as a module. If so, the module will be
> > + called hx711.
> > +
> > config INA2XX_ADC
> > tristate "Texas Instruments INA2xx Power Monitors IIO driver"
> > depends on I2C && !SENSORS_INA2XX
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index b1aa456e6af3..d46e289900ef 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -21,6 +21,7 @@ obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
> > obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > obj-$(CONFIG_HI8435) += hi8435.o
> > +obj-$(CONFIG_HX711) += hx711.o
> > obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
> > obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > diff --git a/drivers/iio/adc/hx711.c b/drivers/iio/adc/hx711.c
> > new file mode 100644
> > index 000000000000..cbc89e467985
> > --- /dev/null
> > +++ b/drivers/iio/adc/hx711.c
> > @@ -0,0 +1,269 @@
> > +/*
> > + * HX711: analog to digital converter for weight sensor module
> > + *
> > + * Copyright (c) Andreas Klinger <ak@xxxxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +#include <linux/err.h>
> > +#include <linux/gpio.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/property.h>
> > +#include <linux/slab.h>
> > +#include <linux/sched.h>
> > +#include <linux/delay.h>
> > +#include <linux/iio/iio.h>
> > +
> > +#define HX711_GAIN_32 2 /* gain = 32 for channel B */
> > +#define HX711_GAIN_64 3 /* gain = 64 for channel A */
> > +#define HX711_GAIN_128 1 /* gain = 128 for channel A */
> > +
> > +
> > +struct hx711_data {
> > + struct device *dev;
> > + dev_t devt;
> > + struct gpio_desc *gpiod_sck;
> > + struct gpio_desc *gpiod_dout;
> > + int gain_pulse;
> > + struct mutex lock;
> > +};
> > +
> > +static void hx711_reset(struct hx711_data *hx711_data)
> > +{
> > + int val;
> > + int i;
> > +
> > + val = gpiod_get_value(hx711_data->gpiod_dout);
>
> could move the val assignment here to the initialization don't think
> it will hit 80 chars
>
I'll change this.
> > + if (val) {
>
> move "int i" here to avoid compiler initialization warnings
>
> > + dev_warn(hx711_data->dev, "RESET-HX711\n");
> > +
> > + gpiod_set_value(hx711_data->gpiod_sck, 1);
> > + udelay(80);
>
> IIRC this chip has quite a bit of latency thresholds, can't use
> usleep_range? Single core embedded systems could have an issue with
> continuous polling.
>
That's a good suggestion. We don't need udelay so i'll change to usleep_range
for the next version
> > + gpiod_set_value(hx711_data->gpiod_sck, 0);
> > +
> > + for (i = 0; i < 1000; i++) {
> > + val = gpiod_get_value(hx711_data->gpiod_dout);
> > + if (!val)
> > + break;
> > + /* sleep at least 1 ms*/
> > + msleep(1);
> > + }
> > + }
> > +}
> > +
> > +static int hx711_cycle(struct hx711_data *hx711_data)
> > +{
> > + int val;
> > +
> > + /* if preempted for more then 60us while SCK is high:
> > + * hx711 is going in reset
> > + * ==> measuring is false
> > + */
> > + preempt_disable();
> > + gpiod_set_value(hx711_data->gpiod_sck, 1);
> > + val = gpiod_get_value(hx711_data->gpiod_dout);
> > + gpiod_set_value(hx711_data->gpiod_sck, 0);
> > + preempt_enable();
> > +
> > + return val;
> > +}
> > +
> > +static unsigned int hx711_read(struct hx711_data *hx711_data)
> > +{
> > + int i;
> > + int ret;
> > + int wert = 0;
> > +
> > + hx711_reset(hx711_data);
> > +
> > + for (i = 0; i < 24; i++) {
> > + wert <<= 1;
> > + ret = hx711_cycle(hx711_data);
> > + if (ret)
> > + wert++;
> > + }
> > +
> > + wert ^= 0x800000;
> > +
> > + for (i = 0; i < hx711_data->gain_pulse; i++)
> > + ret = hx711_cycle(hx711_data);
>
> What is ret used for here?
> > +
> > + return wert;
> > +}
> > +
> > +
> > +static int hx711_read_raw(struct iio_dev *iio_dev,
> > + const struct iio_chan_spec *chan,
> > + int *val, int *val2, long mask)
> > +{
> > + struct hx711_data *hx711_data = iio_priv(iio_dev);
> > + int ret;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + switch (chan->type) {
> > + case IIO_VOLTAGE:
> > + mutex_lock(&hx711_data->lock);
> > + *val = (int)hx711_read(hx711_data);
> > + mutex_unlock(&hx711_data->lock);
> > + ret = IIO_VAL_INT;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > + return ret;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static const struct iio_info hx711_iio_info = {
> > + .driver_module = THIS_MODULE,
> > + .read_raw = hx711_read_raw,
> > +};
> > +
> > +static const struct iio_chan_spec hx711_chan_spec[] = {
> > + { .type = IIO_VOLTAGE,
> > + .channel = 0,
> > + .info_mask_separate =
> > + BIT(IIO_CHAN_INFO_RAW),
> > + .scan_type = {
> > + .sign = 'u',
> > + .realbits = 24,
> > + .storagebits = 32,
> > + .shift = 0,
> > + }
> > + },
> > +};
> > +
> > +static int hx711_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct device_node *node = dev->of_node;
> > + struct hx711_data *hx711_data = NULL;
> > + struct iio_dev *iio;
> > + int ret = 0, ival;
> > +
> > + iio = devm_iio_device_alloc(dev, sizeof(struct hx711_data));
> > + if (!iio) {
> > + dev_err(dev, "failed to allocate IIO device\n");
> > + return -ENOMEM;
> > + }
> > +
> > + hx711_data = iio_priv(iio);
> > + hx711_data->dev = dev;
> > +
> > + mutex_init(&hx711_data->lock);
> > +
> > + hx711_data->gpiod_sck = devm_gpiod_get(dev, "sck", GPIOD_OUT_HIGH);
> > + if (IS_ERR(hx711_data->gpiod_sck)) {
> > + ret = PTR_ERR(hx711_data->gpiod_sck);
> > + goto err;
> > + }
> > +
> > + hx711_data->gpiod_dout = devm_gpiod_get(dev, "dout", GPIOD_OUT_HIGH);
> > + if (IS_ERR(hx711_data->gpiod_dout)) {
> > + ret = PTR_ERR(hx711_data->gpiod_dout);
> > + goto err;
> > + }
> > +
> > + ret = of_property_read_u32 (node, "gain", &ival);
> > + if (!ret) {
> > + switch (ival) {
> > + case 32:
> > + hx711_data->gain_pulse = HX711_GAIN_32;
> > + break;
> > + case 64:
> > + hx711_data->gain_pulse = HX711_GAIN_64;
> > + break;
> > + case 128:
> > + hx711_data->gain_pulse = HX711_GAIN_128;
> > + break;
> > + default:
> > + hx711_data->gain_pulse = HX711_GAIN_128;
> > + }
> > + } else
> > + hx711_data->gain_pulse = HX711_GAIN_128;
> > + dev_dbg(hx711_data->dev, "gain: %d\n", hx711_data->gain_pulse);
> > +
> > + ret = gpiod_direction_input(hx711_data->gpiod_dout);
> > + if (ret < 0) {
> > + dev_err(hx711_data->dev, "gpiod_direction_input: %d\n", ret);
> > + goto err;
> > + }
> > +
> > + ret = gpiod_direction_output(hx711_data->gpiod_sck, 0);
> > + if (ret < 0) {
> > + dev_err(hx711_data->dev, "gpiod_direction_output: %d\n", ret);
> > + goto err;
> > + }
> > +
> > + platform_set_drvdata(pdev, iio);
> > +
> > + iio->name = pdev->name;
> > + iio->dev.parent = &pdev->dev;
> > + iio->info = &hx711_iio_info;
> > + iio->modes = INDIO_DIRECT_MODE;
> > + iio->channels = hx711_chan_spec;
> > + iio->num_channels = ARRAY_SIZE(hx711_chan_spec);
> > +
> > + dev_err(hx711_data->dev, "initialized\n");
> > +
> > + return devm_iio_device_register(dev, iio);
> > +
> > +err:
> > + return ret;
> > +}
> > +
> > +
> > +static int hx711_suspend(struct device *dev)
> > +{
> > + return 0;
> > +}
> > +
> > +static int hx711_resume(struct device *dev)
> > +{
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(hx711_pm_ops, hx711_suspend, hx711_resume);
> > +
> > +
> > +static const struct of_device_id of_hx711_match[] = {
> > + { .compatible = "avia,hx711", },
> > + {},
> > +};
> > +
> > +MODULE_DEVICE_TABLE(of, of_hx711_match);
> > +
> > +static struct platform_driver hx711_driver = {
> > + .probe = hx711_probe,
> > + .driver = {
> > + .name = "hx711-gpio",
> > + .pm = &hx711_pm_ops,
> > + .of_match_table = of_hx711_match,
> > + },
> > +};
> > +
> > +module_platform_driver(hx711_driver);
> > +
> > +MODULE_AUTHOR("Andreas Klinger <ak@xxxxxxxxxxxxx>");
> > +MODULE_DESCRIPTION("HX711 bitbanging driver - ADC for weight cells");
> > +MODULE_LICENSE("GPL");
> > +MODULE_ALIAS("platform:hx711-gpio");
> > +
> > --
> > 2.1.4
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
