> This adds the device tree bindings for the Qualcomm PM8xxx
> ADCs. This is based on the existing DT bindings for the
> SPMI ADC so there are hopefully no controversial features.
nitpicking below
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> Cc: linux-arm-msm@xxxxxxxxxxxxxxx
> Cc: Ivan T. Ivanov <iivanov.xz@xxxxxxxxx>
> Cc: Andy Gross <andy.gross@xxxxxxxxxx>
> Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> Cc: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> ---
> .../bindings/iio/adc/qcom,pm8xxx-xoadc.txt | 160 +++++++++++++++++++++
> 1 file changed, 160 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt
> new file mode 100644
> index 000000000000..6e51e3e74b88
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt
> @@ -0,0 +1,160 @@
> +Qualcomm's PM8xxx voltage XOADC
> +
> +The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Chrystal
crystal
> +oscillator ADC) encompass PM8018, PM8038, PM8058, PM8917 and PM8921.
encompassing
> +
> +Required properties:
> +
> +- compatible: should be one of:
> + "qcom,pm8018-adc"
> + "qcom,pm8038-adc"
> + "qcom,pm8058-adc"
> + "qcom,pm8917-adc"
> + "qcom,pm8921-adc"
> +
> +- reg: should contain the ADC base address in the PMIC, typically
> + 0x197.
> +
> +The following required properties are standard for IO channels, see
> +iio-bindings.txt for more details:
> +
> +- #address-cells: should be set to <1>
> +
> +- #size-cells: should be set to <0>
> +
> +- #io-channel-cells: should be set to <1>
> +
> +- interrupts: should refer to the parent PMIC interrupt controller
> + and reference the proper ADC interrupt.
> +
> +Required subnodes:
> +
> +The ADC channels are configured as subnodes of the ADC. Since some of
> +them are used for calibrating the ADC, these nodes are compulsory:
> +
> +ref_625mv {
> + reg = <0x0c>;
> +};
> +
> +ref_1250mv {
> + reg = <0x0d>;
> +};
> +
> +ref_muxoff {
> + reg = <0x0f>;
> +};
> +
> +These three nodes are used for absolute and ratiometric calibration
> +and only need to have these reg values: they are by hardware defined
they are by hardware definition 1:1 ratio converters that sample ...
> +to be 1:1 ratio converters that sample 625, 1250 and 0 V and create
milliV
or 0.625, 1.250 V
> +an interpolation calibration for all other ADCs.
> +
> +Optional subnodes: any channels other than channel 0x0c, 0x0d and
> +0x0f are optional.
> +
> +Required channel node properties:
> +
> +- reg: should contain the hardware channel number in the range
> + 0 .. 0x0f (4 bits). The hardware only supports 16 channels.
> +
> +Optional channel node properties:
> +
> +- qcom,decimation:
> + Value type: <u32>
> + Definition: This parameter is used to decrease ADC sampling rate.
> + Quicker measurements can be made by reducing decimation ratio.
> + Valid values are 512, 1024, 2048, 4096.
> + If property is not found, default value of 512 will be used.
> +
> +- qcom,ratiometric:
> + Value type: <empty>
> + Definition: Channel calibration type. If this property is specified
> + VADC will use the VDD reference (1.8V) and GND for channel
> + calibration. If property is not found, channel will be
> + calibrated with 0.625V and 1.25V reference channels, also
> + known as absolute calibration.
> +
> +- qcom,ratiometric-ref:
> + Value type: <u32>
> + Definition: The reference voltage pair when using ratiometric
> + calibration:
> + 0 = XO_IN/XOADC_GND
> + 1 = PMIC_IN/XOADC_GND
> + 2 = PMIC_IN/BMS_CSP
> + 3 (invalid)
> + 4 = XOADC_GND/XOADC_GND
> + 5 = XOADC_VREF/XOADC_GND
> +
> +Example:
> +
> +xoadc: xoadc@197 {
> + compatible = "qcom,pm8058-adc";
> + reg = <0x197>;
> + interrupt-parent = <&pm8058>;
> + interrupts = <76 1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> +
> + vcoin {
> + reg = <0x00>;
> + };
> + vbat {
> + reg = <0x01>;
> + };
> + dcin {
> + reg = <0x02>;
> + };
> + ichg {
> + reg = <0x03>;
> + };
> + vph_pwr {
> + reg = <0x04>;
> + };
> + mpp5 {
> + reg = <0x05>;
> + };
> + mpp6 {
> + reg = <0x06>;
> + };
> + mpp7 {
> + reg = <0x07>;
> + };
> + mpp8 {
> + reg = <0x08>;
> + };
> + mpp9 {
> + reg = <0x09>;
> + };
> + usb_vbus {
> + reg = <0x0a>;
> + };
> + die_temp {
> + reg = <0x0b>;
> + };
> + ref_625mv {
> + reg = <0x0c>;
> + };
> + ref_1250mv {
> + reg = <0x0d>;
> + };
> + ref_325mv {
> + reg = <0x0e>;
> + };
> + ref_muxoff {
> + reg = <0x0f>;
> + };
> +};
> +
> +
> +/* IIO client node */
> +iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&xoadc 0x01>, /* Battery */
> + <&xoadc 0x02>, /* DC in (charger) */
> + <&xoadc 0x04>, /* VPH the main system voltage */
> + <&xoadc 0x0b>, /* Die temperature */
> + <&xoadc 0x0c>, /* Reference voltage 1.25V */
> + <&xoadc 0x0d>, /* Reference voltage 0.625V */
> + <&xoadc 0x0e>; /* Reference voltage 0.325V */
> +};
>
--
Peter Meerwald-Stadler
+43-664-2444418 (mobile)
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
