On Mon, Dec 05, 2016 at 01:12:25PM +0100, Benjamin Gaignard wrote: > 2016-12-05 12:23 GMT+01:00 Thierry Reding <thierry.reding@xxxxxxxxx>: > > On Mon, Dec 05, 2016 at 12:08:32PM +0100, Benjamin Gaignard wrote: > >> 2016-12-05 7:53 GMT+01:00 Thierry Reding <thierry.reding@xxxxxxxxx>: > >> > On Fri, Dec 02, 2016 at 11:17:18AM +0100, Benjamin Gaignard wrote: > >> >> Define bindings for pwm-stm32 > >> >> > >> >> version 2: > >> >> - use parameters instead of compatible of handle the hardware configuration > >> >> > >> >> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@xxxxxx> > >> >> --- > >> >> .../devicetree/bindings/pwm/pwm-stm32.txt | 38 ++++++++++++++++++++++ > >> >> 1 file changed, 38 insertions(+) > >> >> create mode 100644 Documentation/devicetree/bindings/pwm/pwm-stm32.txt > >> >> > >> >> diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt > >> >> new file mode 100644 > >> >> index 0000000..575b9fb > >> >> --- /dev/null > >> >> +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt > >> >> @@ -0,0 +1,38 @@ > >> >> +STMicroelectronics PWM driver bindings for STM32 > >> > > >> > Technically this bindings describe devices, so "driver binding" is a > >> > somewhat odd wording. Perhaps: > >> > > >> > STMicroelectronics STM32 General Purpose Timer PWM bindings > >> > > >> > ? > >> done > >> > >> > > >> >> + > >> >> +Must be a sub-node of STM32 general purpose timer driver > >> >> +Parent node properties are describe in ../mfd/stm32-general-purpose-timer.txt > >> > > >> > Again, "driver parent node" is odd. Perhaps: > >> > > >> > Must be a sub-node of an STM32 General Purpose Timer device tree > >> > node. See ../mfd/stm32-general-purpose-timer.txt for details about > >> > the parent node. > >> > > >> > ? > >> > >> done > >> > >> > > >> >> +Required parameters: > >> >> +- compatible: Must be "st,stm32-pwm" > >> >> +- pinctrl-names: Set to "default". > >> >> +- pinctrl-0: List of phandles pointing to pin configuration nodes > >> >> + for PWM module. > >> >> + For Pinctrl properties, please refer to [1]. > >> > > >> > Your indentation and capitalization are inconsistent. Also, please refer > >> > to the pinctrl bindings by relative path and inline, rather than as a > >> > footnote reference. > >> > >> OK > >> > >> > > >> >> + > >> >> +Optional parameters: > >> >> +- st,breakinput: Set if the hardware have break input capabilities > >> >> +- st,breakinput-polarity: Set break input polarity. Default is 0 > >> >> + The value define the active polarity: > >> >> + - 0 (active LOW) > >> >> + - 1 (active HIGH) > >> > > >> > Could we fold these into a single property? If st,breakinput-polarity is > >> > not present it could simply mean that there is no break input, and if it > >> > is present you don't have to rely on a default. > >> > >> I need to know if I have to activate breakinput feature and on which level > >> I will rewrite it like that: > >> Optional parameters: > >> - st,breakinput-polarity-high: Set if break input polarity is active > >> on high level. > >> - st,breakinput-polarity-high: Set if break input polarity is active > >> on low level. > > > > How is that different from a single property: > > > > Optional properties: > > - st,breakinput-polarity: If present, a break input is available > > for the channel. In that case the property value denotes the > > polarity of the break input: > > - 0: active low > > - 1: active high > > > > ? > > For break input feature I need two information: do I have to active it > and if activated > on which level. > I have two solutions: > - one parameter with a value (0 or 1) -> st,breakinput-polarity > - two parameters without value -> st,breakinput-active-high and > st,breakinput-active-low > > By default break input feature is disabled Right, what I was suggesting is that you use the first solution because it's the typical way to use for tristate options. It's also much easier to test for in practice because for the second solution you have to parse two properties before you know whether it is active or not. The second is typically the solution for required properties where only one of the properties is used to override the default. Thierry
Attachment:
signature.asc
Description: PGP signature
