Re: [PATCH v8] iio: st_sensors: harden interrupt handling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 06/22/2016 11:25 AM, Linus Walleij wrote:
> Leonard Crestez observed the following phenomenon: when using
> hard interrupt triggers (the DRDY line coming out of an ST
> sensor) sometimes a new value would arrive while reading the
> previous value, due to latencies in the system.
> 
> We discovered that the ST hardware as far as can be observed
> is designed for level interrupts: the DRDY line will be held
> asserted as long as there are new values coming. The interrupt
> handler should be re-entered until we're out of values to
> handle from the sensor.
> 
> If interrupts were handled as occurring on the edges (usually
> low-to-high) new values could appear and the line be held
> asserted after that, and these values would be missed, the
> interrupt handler would also lock up as new data was
> available, but as no new edges occurs on the DRDY signal,
> nothing happens: the edge detector only detects edges.
> 
> To counter this, do the following:
> 
> - Accept interrupt lines to be flagged as level interrupts
>   using IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW. If the line
>   is marked like this (in the device tree node or ACPI
>   table or similar) it will be utilized as a level IRQ.
>   We mark the line with IRQF_ONESHOT and mask the IRQ
>   while processing a sample, then the top half will be
>   entered again if new values are available.
> 
> - If no interrupt type is indicated from the DT/ACPI,
>   choose IRQF_TRIGGER_HIGH so the above goes into action.
> 
> - If we are flagged as using edge interrupts with
>   IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING: remove
>   IRQF_ONESHOT so that the interrupt line is not
>   masked while running the thread part of the interrupt.
>   This way we will never miss an interrupt, then introduce
>   a loop that polls the data ready registers repeatedly
>   until no new samples are available, then exit the
>   interrupt handler. This way we know no new values are
>   available when the interrupt handler exits and
>   new (edge) interrupts will be triggered when data arrives.
>   Take some extra care to update the timestamp in the poll
>   loop if this happens. The timestamp will not be 100%
>   perfect, but it will at least be closer to the actual
>   events. Usually the extra poll loop will handle the new
>   samples, but once in a blue moon, we get a new IRQ
>   while exiting the loop, before returning from the
>   thread IRQ bottom half with IRQ_HANDLED. On these rare
>   occasions, the removal of IRQF_ONESHOT means the
>   interrupt will immediately fire again.
> 
> Tested successfully on the LIS331DL and L3G4200D by setting
> sampling frequency to 400Hz/800Hz and stressing the system:
> extra reads in the threaded interrupt handler occurs.
> 
> Cc: Giuseppe Barba <giuseppe.barba@xxxxxx>
> Cc: Denis Ciocca <denis.ciocca@xxxxxx>
> Tested-by: Crestez Dan Leonard <cdleonard@xxxxxxxxx>
> Reported-by: Crestez Dan Leonard <cdleonard@xxxxxxxxx>
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>

I also tested v8 and it looks good.
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux