> Am 19.06.2016 um 20:34 schrieb Linus Walleij <linus.walleij@xxxxxxxxxx>:
>
> The first version of this sensor, BMP058, supports sending an
s/058/085/
and in subject line and commit messages in some other patches.
> End-of-Conversion (EOC) interrupt. Add code to support this using
> a completion, in a similar vein as drivers/misc/bmp058.c does.
s/058.c/085.c/
> Make sure to check that we are given a rising edge, because the
> EOC line goes from low-to-high when the conversion is ready.
>
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> ---
> drivers/iio/pressure/bmp280-core.c | 83 ++++++++++++++++++++++++++++++++++----
> drivers/iio/pressure/bmp280-i2c.c | 3 +-
> drivers/iio/pressure/bmp280-spi.c | 3 +-
> drivers/iio/pressure/bmp280.h | 3 +-
> 4 files changed, 81 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/iio/pressure/bmp280-core.c b/drivers/iio/pressure/bmp280-core.c
> index af422d224db4..ca9ed843efcc 100644
> --- a/drivers/iio/pressure/bmp280-core.c
> +++ b/drivers/iio/pressure/bmp280-core.c
> @@ -25,6 +25,9 @@
> #include <linux/iio/sysfs.h>
> #include <linux/gpio/consumer.h>
> #include <linux/regulator/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h> /* For irq_get_irq_data() */
> +#include <linux/completion.h>
>
> #include "bmp280.h"
>
> @@ -32,6 +35,8 @@ struct bmp280_data {
> struct device *dev;
> struct mutex lock;
> struct regmap *regmap;
> + struct completion done;
> + bool use_eoc;
> const struct bmp280_chip_info *chip_info;
> struct regulator *vddd;
> struct regulator *vdda;
> @@ -435,16 +440,32 @@ static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)
> unsigned int delay_us;
> unsigned int ctrl;
>
> + if (data->use_eoc)
> + init_completion(&data->done);
> +
> ret = regmap_write(data->regmap, BMP280_REG_CTRL_MEAS, ctrl_meas);
> if (ret)
> return ret;
>
> - if (ctrl_meas == BMP180_MEAS_TEMP)
> - delay_us = 4500;
> - else
> - delay_us = conversion_time_max[data->oversampling_press];
> -
> - usleep_range(delay_us, delay_us + 1000);
> + if (data->use_eoc) {
> + /*
> + * If we have a completion interrupt, use it, wait up to
> + * 100ms. The longest conversion time listed is 76.5 ms for
> + * advanced resolution mode.
> + */
> + ret = wait_for_completion_timeout(&data->done,
> + 1 + msecs_to_jiffies(100));
> + if (!ret)
> + dev_err(data->dev, "timeout waiting for completion\n");
> + } else {
> + if (ctrl_meas == BMP180_MEAS_TEMP)
> + delay_us = 4500;
> + else
> + delay_us =
> + conversion_time_max[data->oversampling_press];
> +
> + usleep_range(delay_us, delay_us + 1000);
> + }
>
> ret = regmap_read(data->regmap, BMP280_REG_CTRL_MEAS, &ctrl);
> if (ret)
> @@ -686,16 +707,28 @@ static const struct bmp280_chip_info bmp180_chip_info = {
> .read_press = bmp180_read_press,
> };
>
> +static irqreturn_t bmp058_eoc_irq(int irq, void *d)
> +{
> + struct bmp280_data *data = d;
> +
> + complete(&data->done);
> +
> + return IRQ_HANDLED;
> +}
> +
> +
> int bmp280_common_probe(struct device *dev,
> struct regmap *regmap,
> unsigned int chip,
> - const char *name)
> + const char *name,
> + int irq)
> {
> int ret;
> struct iio_dev *indio_dev;
> struct bmp280_data *data;
> unsigned int chip_id;
> struct gpio_desc *gpiod;
> + unsigned long irq_trig;
>
> indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
> if (!indio_dev)
> @@ -763,5 +796,39 @@ int bmp280_common_probe(struct device *dev,
> if (ret < 0)
> return ret;
>
> - return devm_iio_device_register(dev, indio_dev);
> + ret = devm_iio_device_register(dev, indio_dev);
> + if (ret) {
> + dev_err(dev, "unable to register IIO device\n");
> + return ret;
> + }
> +
> + /*
> + * Attempt to grab an optional EOC IRQ - only the BMP058 has this
> + * however as it happens, the BMP058 shares the chip ID of BMP180
> + * so we look for an IRQ if we have that.
> + */
> + if (irq <= 0 || (chip_id != BMP180_CHIP_ID))
> + return 0;
> +
> + irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
> + if (irq_trig != IRQF_TRIGGER_RISING) {
> + dev_err(dev, "non-rising trigger given for EOC interrupt, "
> + "trying to enforce it\n");
> + irq_trig = IRQF_TRIGGER_RISING;
> + }
> + ret = devm_request_threaded_irq(dev,
> + irq,
> + bmp058_eoc_irq,
> + NULL,
> + irq_trig,
> + name,
> + data);
> + if (ret) {
> + /* Bail out without IRQ but keep the driver in place */
> + dev_err(dev, "unable to request DRDY IRQ\n");
> + return 0;
> + }
> +
> + data->use_eoc = true;
> + return 0;
> }
> diff --git a/drivers/iio/pressure/bmp280-i2c.c b/drivers/iio/pressure/bmp280-i2c.c
> index b422600f34e0..eb2b727109b8 100644
> --- a/drivers/iio/pressure/bmp280-i2c.c
> +++ b/drivers/iio/pressure/bmp280-i2c.c
> @@ -32,7 +32,8 @@ static int bmp280_i2c_probe(struct i2c_client *client,
> return bmp280_common_probe(&client->dev,
> regmap,
> id->driver_data,
> - id->name);
> + id->name,
> + client->irq);
> }
>
> static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
> diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
> index a24ea5f62c5e..cfb6248ceb1f 100644
> --- a/drivers/iio/pressure/bmp280-spi.c
> +++ b/drivers/iio/pressure/bmp280-spi.c
> @@ -44,7 +44,8 @@ static int bmp280_spi_probe(struct spi_device *spi)
> return bmp280_common_probe(&spi->dev,
> regmap,
> id->driver_data,
> - id->name);
> + id->name,
> + spi->irq);
> }
>
> static const struct of_device_id bmp280_of_spi_match[] = {
> diff --git a/drivers/iio/pressure/bmp280.h b/drivers/iio/pressure/bmp280.h
> index 9249956bc8bf..ad0e5778c6b5 100644
> --- a/drivers/iio/pressure/bmp280.h
> +++ b/drivers/iio/pressure/bmp280.h
> @@ -82,4 +82,5 @@ extern const struct regmap_config bmp280_regmap_config;
> int bmp280_common_probe(struct device *dev,
> struct regmap *regmap,
> unsigned int chip,
> - const char *name);
> + const char *name,
> + int irq);
> --
> 2.4.11
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
