On Wednesday 08 June 2016 08:34 PM, Andrew F. Davis wrote:
On 06/07/2016 05:30 PM, Guenter Roeck wrote:
On Fri, Jun 03, 2016 at 10:17:55AM -0500, Andrew F. Davis wrote:
On 06/03/2016 09:14 AM, Laxman Dewangan wrote:
On Friday 03 June 2016 06:59 PM, Guenter Roeck wrote:
On 06/03/2016 03:06 AM, Jonathan Cameron wrote:
On 01/06/16 13:34, Laxman Dewangan wrote:
The INA3221 is a three-channel, high-side current and bus voltage
monitor
with an I2C interface from Texas Instruments. The INA3221 monitors both
shunt voltage drops and bus supply voltages in addition to having
programmable conversion times and averaging modes for these signals.
The INA3221 offers both critical and warning alerts to detect multiple
programmable out-of-range conditions for each channel.
Add support for INA3221 SW driver via IIO ADC interface. The device is
register as iio-device and provides interface for voltage/current
and power
monitor. Also provide interface for setting oneshot/continuous mode and
critical/warning threshold for the shunt voltage drop.
Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx>
Hi Laxman,
As ever with any driver lying on the border of IIO and hwmon, please
include
a short justification of why you need an IIO driver and also cc the
hwmon list + maintainers. (cc'd on this reply).
I simply won't take a driver where the hwmon maintainers aren't happy.
As it stands I'm not seeing obvious reasons in the code for why this
should be an IIO device.
Me not either.
I have a hwmon driver for the same chip pending from Andrew Davis (TI)
which I am just about to accept. We had directed Andrew back in April
to write a hwmon driver for the chip, which he did.
Thanks Guenter, I found the series
[PATCH v2 0/2] Add support for INA3221 Triple Current/Voltage Monitors
Looks fine to me. I can use the hwmon.
If you search even further back you can see I originally went with an
IIO driver as well, comparing the IIO and hwmon version for the simple
use cases I needed the hwmod version turned out much simpler, so it was
probably the right framework for now.
However, some of the stuff from my patch are not there which I will add
later once original patch applied:
- Dynamic mode changes for continuous and one-shot from sysfs.
- In one shot, when try to read voltage data, do conversion and then read.
My attempt is rather minimal, to be honest I like your stab at this
driver better in some ways, especially relating to DT putting each
channel in its own node with labels, I think this is a bit more clean
and will be more extendable if/when new multi-channel monitor chips are
made.
Not sure whether exporting the following will help or not. Can you
please confirm?
- Oversampling time i.e. average sample
- conversion time for bus voltage and shunt voltage if default is not
suited for system.
These can always be added as needed, but the DT changes are not as easy.
I would like it if this got in this cycle but if you think something
will be needed to help your improvements, that can not be added
incrementally, it would probably be best to get them into the initial DT
binding doc now.
Andrew,
with this, the hwmon driver is pretty much on hold. What do you want me to do ?
Should I wait for DT updates ?
If Laxman would like to commit to making these changes I do not problem
waiting a bit to get this right the first time.
If we don't hear back soon then I'd just take it as is and anything
needing to be fixed can be later.
I will be able to post the patch tomorrow.
I think this series can be applied and then on top of it, I will post
the dt changes and other my changes.
As this is new driver and no one using now, it will be fine to have dt
changes if everything complete in one cycle.
I will work from the tree on which this applied to post my patches.
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
