On 03/06/16 12:48, Laxman Dewangan wrote: > > On Friday 03 June 2016 03:49 PM, Jonathan Cameron wrote: >> On 03/06/16 03:07, Rob Herring wrote: >>> On Wed, Jun 01, 2016 at 06:04:12PM +0530, Laxman Dewangan wrote: >>>> + >>>> +Optional properties: >>>> +------------------ >>>> +one-shot-average-sample: Integer, Number of sample to average before >>>> + putting in the registers in oneshot mode. >> Pick a sensible default in the driver then leave this to userspace to >> control. > >>>> + >>>> +one-shot-vbus-conv-time-us: Integer in microseconds, ADC conversion time for >>>> + bus voltage reading in oneshot mode. >> Hmm. This one is a little non obvious. It's really controlling the noise >> level more than anything else. Kind of integration time I guess though >> not described as such in the datasheet. > > Yes the conversion time and average time help to reduce noise on conversion and efefctively tune the conversion delay per channel based on system need. > > From data sheet: > The INA3221 has programmable conversion times for both the shunt and bus voltage measurements. The conversion times for these measurements can be selected from 140 µs to 8.244 ms. The conversion time settings, along with the programmable averaging mode, enable the INA3221 to be configured to optimize available timing requirements in a given application. For example, if a system requires data to be read every 2 ms with all three channels monitored, the INA3221 can be configured with the conversion times for the shunt and bus voltage measurements set to 332 µs. The INA3221 can also be configured with a different conversion time setting for the shunt and bus voltage measurements. This approach is common in applications where the bus voltage tends to be relatively stable. This situation allows for the time focused on the bus voltage measurement to be reduced relative to the shunt voltage measurement. For example, the shunt voltage conversion time can be set to 4.156 ms with the > bus voltage conversion time set to 588 µs for a 5-ms update time. > There are trade-offs associated with conversion time settings and the averaging mode used. The averaging feature can significantly improve the measurement accuracy by effectively filtering the signal. This approach allows the INA3221 to reduce the amount of noise in the measurement that may be caused by noise coupling into the signal. A greater number of averages allows the INA3221 to be more effective in reducing the measurement noise component. The trade-off to this noise reduction is that the averaged value has a longer response time to input signal changes. This aspect of the averaging feature is mitigated to some extent with the critical alert feature that compares each single conversion to determine if a measured signal (with its noise component) has exceeded the maximum acceptable level. > > > > We have different values for these parameters for oneshot and continuous mode. > > >> >> Again, I don't think this is really device tree material. >> However, you could argue the right decision on this is hardware dependant >> as it really depends on ripple in the voltages? Not how it's described in >> the datasheet though. > > The tuning is done on platform specific and hence it is from the device tree here. > > >>>> + >>>> +one-shot-shunt-conv-time-us: Integer in microseconds, ADC conversion time for >>>> + shunt voltage reading in oneshot mode. >>>> + >>>> +continuous-average-sample: Integer, Number of sample to average before >>>> + putting in the registers in continuous mode. >> Classic oversampling - not device tree material as it may well want >> runtime configuration. > > Yaah, it is oversampling. > > >>>> + >>>> +continuous-vbus-conv-time-us: Integer in microseconds, ADC conversion time for >>>> + bus voltage reading in continuous mode. >> Why should these be different from the one-shot versions? Might be >> separately controlled (though I don't think they are). If one setting >> makes sense fo the hardware in oneshot mode, surely the same setting makes >> sense in continuous mode. > > The oneshot and continuous mode get change in run time. We have different configuration for the continuous mode and one shot mode for the oversampling. > >>>> + >>>> +continuous-shunt-conv-time-us: Integer in microseconds, ADC conversion time for >>>> + shunt voltage reading in continuous mode. >>> These all need vendor prefix and need to state the valid range of >>> values. >>> >>>> + >>>> +enable-power-monitor: Boolean, Enable power monitoring of the device. >> Is this the power good stuff? description should be more detailed. > > If there is no shunt resistance then we can not enable power monitor > on that rail. Device does not mandate to have shunt and so this is > based on platforms. The voltage shunt also becomes meaningless (unless you have other very small voltage drops to measure!). So drop that channel as well. Either it is there to do current measurement or it isn't. > > >>>> + >>>> +enable-continuous-mode: Boolean. Device support oneshot and continuous >>>> + mode for the channel data conversion. Presence >>>> + of this property will enable the continuous >>>> + mode from boot. >> Is the difference between driver load time and the point where usespace can >> set it up significant enough to justify this? > > We change the mode dynamically. If we have more core then goto the > continuous mode so that we can apply throttling if power consumption > is going more than requirement. If we are running single core then > change to oneshot mode. That's definitely a usespace or firmware decision, not a kernel one to my mind - unless I guess you an enforcing bringing this device up before firing up the additional cores? Then it's nasty but I can start to see some justification. > > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
