On 2016-02-09 21:30, Lars-Peter Clausen wrote:
On 02/09/2016 09:22 AM, Sean Nyekjær wrote:
On 2016-02-03 15:31, Sean Nyekjaer wrote:
Devicetree can provide platform data
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@xxxxxxxxx>
Lars do you have time to look at this before i'm fixing the comments from
Jonathan and Rob :-)
The obvious thing is to use '-' instead of '_' since that is the DT convention.
I'm removing the defines in from the DT doc.
Other than that this non-trivial. This is the first binding for such a
device and it is always hard to come up with a good ABI without knowing what
other similar devices might need to be supported by the same bindings. And
it is also not always clear what is hardware description and what is driver
policy.
I was hoping we could cooperate on enabling this feature. It's not the
majority of linux devices that are using board files any more.
The external resistor configuration should be clear, that's a description of
the hardware whether the resistor exists or not.
For the others it's not so clear. E.g. the DC-to-DC converter configuration,
this is most certainly not a description of the hardware. But we could get
away with it by saying this is a system level design decision and is made by
the system designer based on the operating parameters of the hardware and
hence is policy that belongs in the DT. It might make sense to follow what
the regulator bindings do here, even though the regulator is not exposed
externally.
The configuration of the output pin (voltage level, current level, etc) is
certainly influenced by the restrictions of the hardware itself. You don't
want to allow a configuration that can damage the hardware. But on the other
hand it is still a valid usecase for some applications to switch between two
setups at runtime, which is something you said you need to be able to do.
I can't why enabling configuration of the DAC from the DT is posing a
greater
risk of damaging hardware than the previous way of editing the board file.
Here we might want to use something similar to pinctrl where the devicetree
can offer a selection of valid configurations and the driver can switch
between those configurations.
- Lars
[...]
I'll submit an PATCH v3 where i have removed the defines from the DT doc
and introduce checks for the values passed from DT.
/Sean
+static struct ad5755_platform_data *ad5755_parse_dt(struct device *dev)
+{
+ struct device_node *np = dev->of_node;
+ struct device_node *pp;
+ struct ad5755_platform_data *pdata;
+ unsigned int tmp;
+ unsigned int tmparray[3];
+ int devnr;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return NULL;
+
+ pdata->ext_dc_dc_compenstation_resistor =
+ of_property_read_bool(np,
"adi,ext_dc_dc_compenstation_resistor");
+
+ if (!of_property_read_u32(np, "adi,dc_dc_phase", &tmp))
+ pdata->dc_dc_phase = tmp;
+ else
+ pdata->dc_dc_phase = AD5755_DC_DC_PHASE_ALL_SAME_EDGE;
+
+ if (!of_property_read_u32(np, "adi,dc_dc_freq", &tmp))
+ pdata->dc_dc_freq = tmp;
+ else
+ pdata->dc_dc_freq = AD5755_DC_DC_FREQ_410kHZ;
+
+ if (!of_property_read_u32(np, "adi,dc_dc_maxv", &tmp))
+ pdata->dc_dc_maxv = tmp;
+ else
+ pdata->dc_dc_maxv = AD5755_DC_DC_MAXV_23V;
+
+ devnr = 0;
+ for_each_child_of_node(np, pp) {
+ if (devnr > AD5755_NUM_CHANNELS) {
+ dev_err(dev, "There is to many channels defined in DT\n");
+ goto error_out;
+ }
+
+ if (!of_property_read_u32(pp, "adi,mode", &tmp))
+ pdata->dac[devnr].mode = tmp;
+ else
+ pdata->dac[devnr].mode = AD5755_MODE_CURRENT_4mA_20mA;
+
+ pdata->dac[devnr].ext_current_sense_resistor =
+ of_property_read_bool(pp, "adi,ext_current_sense_resistor");
+
+ pdata->dac[devnr].enable_voltage_overrange =
+ of_property_read_bool(pp, "adi,enable_voltage_overrange");
+ if (!of_property_read_u32_array(pp, "adi,slew", tmparray, 3)) {
+ pdata->dac[devnr].slew.enable = tmparray[0];
+ pdata->dac[devnr].slew.rate = tmparray[1];
+ pdata->dac[devnr].slew.step_size = tmparray[2];
+ } else {
+ pdata->dac[devnr].slew.enable = false;
+ pdata->dac[devnr].slew.rate = AD5755_SLEW_RATE_64k;
+ pdata->dac[devnr].slew.step_size = AD5755_SLEW_STEP_SIZE_1;
+ }
+
+ devnr++;
+ }
+
+ return pdata;
[...]
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
